Hiboy HC01 User manual
Hoverboard Kart HC01
USER MANUAL
Read the warnings on the board and at the beginning of this manual.
Always wear a helmet.
Other protective equipment is highly recommended (knee pads, long sleeves, wrist guards)
Find an open, flat area with clean pavement for your first ride.
Do not ride through puddles or other bodies of water.
Do not ride rainy days.
Do not ride double or carry any passengers.
Do not ride with high heels. Always ride with properly strapped closed toe shoes.
Do not ride on low traction surfaces (including, but not limited to, wet ground, loose sand and ice).
When traversing small bumps or uneven terrain, maintain a moderate speed of 2-4 mph (3-6 km/h)
and keep your knees bent. Do not go too slow or too fast; otherwise you may lose control and fall.
Warning
1. Riding Safety
2. Packing List
3. Assembly Introduction
4. Service and Warranty
5. Question & Answer
Contents
2
4
5
9
10
Thanks for choosing Hiboy Hoverboard Kart HC01 (hereinafter referred to as Hiboy HC01).
To enjoy the many features of your Hiboy HC01 you must read and follow these instructions.
Have fun and enjoy your ride!
１
RIDING SAFETY
1. The hoverboard kart has been designed a recreational product. Before mastering riding
skills, you need to practice. Freeman Inc. is not responsible for any injuries or damage
caused by a rider's inexperience or failure to follow the instructions in this document.
2. Please understand that you can reduce the risk by following all the instructions and
warnings in this manual, but you cannot eliminate all the risks. Remember that whenever
you ride the hoverboard kart you risk injury or death from loss of control, collisions, and falls.
When entering into public spaces always comply with the local laws and regulations. Be
cautious and always keep a safe distance between you and other people or vehicles when
riding. Be alert and slow down when entering unfamiliar areas.Users are responsible for
following all local, state, and federal laws regarding the use of this product.
3. Always wear a helmet when riding. Use an approved bicycle or skateboard
helmet that fits properly with the chin strap in place, and provides protection for
the back of your head.
4. Do not attempt your first ride in any area where you might encounter children, pedestrians,
pets, vehicles, bicycles, or other obstacles and potential hazards.
5. PARENTAL/ADULT SUPERVISION IS NECESSARY WITH CHILDREN UNDER 12. If
you are under 18, please get your parents permission.
２
6. The safety speed is 6.2mph. When the speed is over 7.5mph, the kart will be out of control
for 0.3-0.5s and user can’t apply the brakes immediately.
7. The hoverboard kart is not for users weighing less than 44lbs than 44lbs/20kg or
more than 270lbs/120kg. The maximum weight limit of 270 lbs (120 kg) includes items
that might be worn or carried such as backpacks, clothes, or personal items. Failure to
adhere to the minimum and maximum weight limits can cause personal injury to the user
and damage to the hoverboard kart.
8. Do not allow anyone to ride your hoverboard kart on his/her own unless they have carefully
read this manual. The safety of new riders is your responsibility. Assist new riders until they
are comfortable with the basic operation of the hoverboard kart. Make sure each new rider
wears a helmet and other protective gear.
9. Before each ride check for loose fasteners, damaged components. If the hoverboard
makes abnormal sounds or signals an alarm, immediately stop riding.
10. Never ride at high speeds on uneven terrain or slopes. Never ride in the dark, or dimly
lit areas. Do not ride in the snow, in the rain, or on roads which are wet, muddy, icy, or that
are slippery for any reason. Do not ride over obstacles (sand, loose gravel, or sticks). Doing
so could result in a loss of balance or traction and could cause a fall. Never ride backwards
for long distances or at high speeds.
３
４
PACKING LIST
1x Frame (2 parts)
1x Adjustment knob 1x Allen Wrench 4x Screw washer
1x Wrench
2x Handles 1x Kart seat
4x Screw
4x Velcro
1x Gasket
５
ASSEMBLY INTRODUCTION
1. Install the handles on the frame on both sides with the nuts.
2. Cut the gasket into 4 pieces and insert the gaskets into the
metal pads to protect your hoverboard from scratches
６
2
.
Fasten the ajustment knob into the hole to
connect front frame and rear frame.
3
.
Install
t
h
e
s
e
a
t
o
n
t
h
e
f
r
a
m
e
.
Screw washer
Screw
7
4. Adjust the slidable metal plates to fit your hoverboard.
then fasten the nut tight.
slidable metal plates
８
Velcro strap
5
.
Put and adjust the velcro straps tight.
6
.
Y
our
kar
t
i
s
read
y to go.
９
SERVICE AND WARRANTY
1. The warranty period is consistent with the national and local warranty policy.The warranty period
is calculated from the date of purchase by the user(on the basis of the date on the purchase receipt).
2. Maintenance costs beyond the warranty period and beyond the scope of the warranty only incur
maintenance costs.
3. If there is any help or accesorry replacement needed, please try to send messages to Hiboy:
@HiboyUS
HiboyUS
www.hiboy.com
hiboyus
@Hiboy_Official
10
QUESTION & ANSWER
Q: What if there is missing kart accessory or broken part?
And Hiboy Support Team will reply you soon and send correct accessory or part replacement.
Q: Don’t like the user manual. Is there a Hiboy kart assembly video to follow?
A: There is a video in YouTube about Hiboy kart assembly,
by searching “how to assemble a hiboy kart” in YouTube.
Q: How to make Swagtron hoverboard T6 fit the Kart?
(There are handles on the middle of Swagtron hoverboard T6)
A: You may revise your hoverboard by moving the middle handles.(Other customers’ suggestion)
Q: What if the quick-wear part got broke, for example velcro straps?
A: Please feel free to contact Hiboy Support Team to get free replacement by sending
Or you may search “hoverboard velcro straps” in Amazon and buy for replacement.
www.hiboy.com
Table of contents
Other Hiboy Hoverboard manuals
