Hover-1 RAPTOR User manual

H OV E R B OA R D AT TAC H M EN T
RAPTOR
OPERATION MANUAL
H1-RPT-BGY

1
HELMETS SAVE LIVES!
Always wear a properly fitted helmet that complies with CPSC or CE safety standards when you
ride your hoverboard.
Correct Fit:
Make sure your helmet
covers your forehead.
Incorrect Fit:
Forehead is exposed and
vulnerable to serious injury.

Please visit
www.hover-1.com/troubleshoot
to request replacements for
missing or defective parts
2
This manual is designed to give you the information you need for the safe operation and maintenance of
your new Raptor. Please read it thoroughly before riding your Raptor.
INTRODUCTION
WARNING
Make sure you read this complete manual before riding
your Raptor. Even if you are an experienced rider, it is
important that you read this manual to ensure your
safety. Failure to read this manual or follow its guidelines
could lead to serious injury or death.

3
RAPTOR DIAGRAM
SPECIFICATIONS
Compatibility: Most 6.5” hoverboards
Max Supported Weight: Refer to your hoverboard’s manual
Wheel Size: 4” swivel caster wheel
Seat Material: Polypropylene
1. Racing Flag
2. Bucket Seat
3. Handlebar (R)
4. Seat Frame
5. Lockers
6. Foot Rests
7. Caster Wheel
8. Fog Blaster & Mount
9. Dual Shocks
10. Handlebar (L)
11. Pedal Mounts
12. Adjustable Strap
13. Frame Extension
8
10
11
9
2
1
3
7
54
13 12
6

4
PARTS LIST
(1) Fog Blaster Mount
(1) Fog Blaster
(1) Charging Cable
(1) Seat
(1) Seat Frame with
Suspension
(1) Front Frame
(2) Lockers
(4) M8 X 38 Screws
(4) M6 X 16 Screws
(4) Mounting Screws
(4) 8 mm Nuts
(4) 6 mm Nuts
Tool Set:
AWrench
A
Hex Key and Screwdriver
B
B
(4) Hook & Loop
Straps with Rubber
Protectors
(1) Flag Set
(1) Flag Holder
(1) Right Handlebar
(1) Left Handlebar

ASSEMBLING YOUR RAPTOR
Remove all Raptor contents from the box. Ensure all contents from the “PARTS LIST” section are accounted
for.
1. Locate the seat fame. Move the 2 suspension shocks into the u-shaped holders at the rear of the seat
frame. You may need to twist the shocks to enure the holes at the end of the shocks align with the holes of
the u-shaped holders. Insert an M8 x 38 screw through each holder and cap each one with an 8 mm nut. Use
the hex key and hex wrench to make sure the lug nuts are completely tightened to the screws.
5
Please visit
x 2
Tools
needed

6
x 2
2. Insert the left and right handlebar mounts into the seat frame as shown below. Align the holes of the handlebar
mounts with the holes in the seat frame. Align the hole of the ag holder with the hole in the seat frame on either
side. This will be where the ag is inserted later. Insert the 8 X 38 screws into the seat frame holes and attach the 8
mm nuts to the end of the screws by twisting them on clockwise. Hold the screws in place with the hex key and
turn the nuts clockwise with the wrench to tighten them. Make sure the screws and nuts are tightly secured.
3. Insert the front frame into the seat frame. Adjust the front frame to your preferred length. Remove the black bolt
and the rst white washer from the end of each locker. Fully insert the screwed section of one locker into the seat
frame holes. Add the white washer and black bolt back onto the locker once it is fully inserted and twist them on
clockwise until they are tightly secured. Close the locker clamp tightly. Repeat these steps on the other side of the
seat frame with the other locker.
Tools
needed

7
4. Attach the fog blaster to the fog blaster mount as shown below. Screw in the 4 mounting screws using the
screwdriver at the end of the included hex key. Make sure the 2 larger holes of the fog blaster mount are facing
forward.
X 4
Tools
needed
5. At this point in the assebly, you should have the fog blaster xed on the mount, both handlebars xed to the seat
frame, the ag tube xed to the seat frame, and the front frame should be interlocked with the seat frame.

8
6. Align the holes of the bucket seat with the holes of the seat frame and fog blaster mount. Insert th M6 x 16 screws
into the holes in the bucket seat and cap each screw with a 6 mm nut. Hold the screws in place with the hex key
and turn the nuts clockwise with the wrench to tighten them until the bucket seat is secured.
7. Your Raptor is now assembled!
x 4
Tools
needed

Water
12
FOG BLASTER DIAGRAM
USING & MAINTAINING YOUR FOG BLASTER
1. Charging Port
2. Water Tank
3. Power Button
4. LED Lights & Sound Effects
Button
5. Fog Vent & LED Lights
5
3
Before using the fog blaster, connect the included charging cable to the fog blaster’s charging port and a
USB outlet (Figure 1). A red light will appear on the fog blaster while charging. When the light turns off, your
fog blaster is fully charged. A full change may take up to 4 hours. Unplug the charging cable. Next, press and
hold down the water tank buttons while pouring water into the water tank (Figure 2). Release the buttons
when the tanks are filled. Do not overfill!
Hold down the button to open
the water tank and pour
water into it
(Figure 1) (Figure 2)
1
2
4

9
Carefully follow the instructions shown on the following pages to attach the Raptor to your hoverboard. Read
this entire manual before riding your Raptor.
Your Raptor must be completely assembled before attaching it to your hoverboard. Please refer to the
“ASSEMBLING YOUR RAPTOR” section of the manual for assembly instructions.
1. Place the handlebar mounts onto the foot pads of your hoverboard. Ensure the mounts are centered on
the foot pads of your hoverboard as much as possible.
ATTACHING THE RAPTOR TO YOUR HOVERBOARD
SPACE EVENLY

10
2. Secure the Raptor to your hoverboard using 2 of the included hook and loop straps. The other 2 straps
included are spares. With the fastener side facing away from your hoverboard, thread the straps through the
front hole of each handlebar mount.
3. Wrap both straps under your hoverboard and pull them through to the other side. Insert the straps into the
rear hole of the handlebar mounts. Fasten the front and rear sides of the straps. The rubber protectors on the
straps should be centered underneath the hoverboard, with side B (as shown in the diagram below) facing
the ground. Make sure they are tightly secured to the hoverboard.

11
4. WARNING: Do not over-tighten the straps when you are attaching your Raptor to your hoverboard. Ensure
that the Raptor is securely attached to the hoverboard.
5. Assemble the flag by inserting one of the included flag rods into the opening in the flag fabric. Attach the
coupling tubes to the flag rods. Combine the remaining rods together by inserting them into each other at
the coupling points. Insert the assembled flag set into the flag tube.
6. When fully assembled, your Raptor should look like the diagram below.

13
RAPTOR OPERATION
It is important that you fully understand all the functions of your Raptor. If these functions are not used
correctly, you will not have full control of your Raptor.
Practice using the Raptor at slower speeds in a flat, open area before riding the Raptor in other spaces.
BEFORE RIDING
WARNING
Any hoverboard that does not work properly can cause
you to lose control and fall. Inspect the entire device
thoroughly before every ride, and do not ride it until any
problems have been corrected.
WARNING
Do not ride a Raptor with a part that is damaged.
Replace the damaged part before riding.

14
Ensure that your Raptor and hoverboard are in proper working order each time you ride. If a part of the
Raptor does not function correctly, please contact our Customer Support Center.
• Ensure the battery of your hoverboard is fully charged before riding your Raptor.
• Ensure that the screws and nuts on the Raptor are tightly secured before each ride.
• Check to ensure the tires of your hoverboard are not worn.
• Check to ensure all connections are maintained on your hoverboard.
• Make sure your hoverboard is calibrated and running properly.
PRE-RIDE RAPTOR CHECKLIST

15
SAFETY PRECAUTIONS
The first rule of safe riding is to use common sense. The Raptor cannot protect you in a crash, against impact,
or from loss of control the way a car can. The Raptor can tip over sideways or pitch you over the front wheel
if you don’t ride it properly. Please read the following safety precautions to operate your Raptor safely.
Different localities and countries have different laws governing riding on public roads, and you should check
with local officials to ensure you are complying with these laws.
Hover-1 is not liable for tickets or violations given to riders who do not follow these regulations.
• For your safety, always wear a helmet that meets CPSC or CE safety standards. In the event of an accident,
a helmet can protect you from serious injury and in some cases, even death.
• Obey all local laws, stop signs, pedestrian crosswalks, etc.
• If you are riding with other riders, maintain a safe distance between each other to avoid collisions.
• Ride defensively; expect the unexpected.
• Give pedestrians the right-of-way.
• Do not ride too close to pedestrians. Alert them if you intend to pass them from behind.
• Slow down at all street intersections and look to the left and right before crossing.
•Obey all traffic signals.
• Always use proper hand signals for turning and stopping. Give signals 100 ft before stopping or turning and
always return both hands to the handlebars before stopping or turning.
• Watch for cars when pulling into traffic and watch for the sudden opening of car doors.
• Avoid potholes, drainage grates, or other hazards.
• Be careful when riding on soft road edges, gravel, sand and uneven surfaces. Ride slowly and avoid quick
turns when riding on these surfaces.
• Never hitch onto other vehicles.
• Do not attempt any stunts or tricks with the Raptor. Do not race in traffic.
• Do not weave in and out of traffic or swerve from side to side.
• A crash can put extraordinary stress on Raptor’s components, possibly causing them to fatigue
prematurely. Components suffering from stress fatigue can fail suddenly, causing loss of control or
serious injury.
CAUTION: RIDING IN WET WEATHER
It is recommended that you do not ride your Raptor in wet weather, as the electronic components of the
hoverboard may be damaged if exposed to water. Stopping distances can be longer in wet conditions than
in dry conditions.
1. This product is strictly forbidden to be used on roads and highways unless your local laws state otherwise.
You must wear a safety helmet, knee and elbow pads, and other necessary protective gear when riding your
Raptor.
2. Due to the nature of this product, the assembly pieces should be checked before every ride to avoid an
accident while riding.
3. Do not make a sharp turns, as you may drift and overturn the Raptor, which can result in injury to yourself
and/or damage the unit.
4. Do not operate near swimming pools or other bodies of water.

16
The first rule of safe riding is to use common sense. The Raptor cannot protect you in a crash, against impact,
or from loss of control the way a car can. The Raptor can tip over sideways or pitch you over the front wheel
if you don’t ride it properly. Please read the following safety precautions to operate your Raptor safely.
Different localities and countries have different laws governing riding on public roads, and you should check
with local officials to ensure you are complying with these laws.
Hover-1 is not liable for tickets or violations given to riders who do not follow these regulations.
• For your safety, always wear a helmet that meets CPSC or CE safety standards. In the event of an accident,
a helmet can protect you from serious injury and in some cases, even death.
• Obey all local laws, stop signs, pedestrian crosswalks, etc.
• If you are riding with other riders, maintain a safe distance between each other to avoid collisions.
• Ride defensively; expect the unexpected.
• Give pedestrians the right-of-way.
• Do not ride too close to pedestrians. Alert them if you intend to pass them from behind.
• Slow down at all street intersections and look to the left and right before crossing.
•Obey all traffic signals.
• Always use proper hand signals for turning and stopping. Give signals 100 ft before stopping or turning and
always return both hands to the handlebars before stopping or turning.
• Watch for cars when pulling into traffic and watch for the sudden opening of car doors.
• Avoid potholes, drainage grates, or other hazards.
• Be careful when riding on soft road edges, gravel, sand and uneven surfaces. Ride slowly and avoid quick
turns when riding on these surfaces.
• Never hitch onto other vehicles.
• Do not attempt any stunts or tricks with the Raptor. Do not race in traffic.
• Do not weave in and out of traffic or swerve from side to side.
• A crash can put extraordinary stress on Raptor’s components, possibly causing them to fatigue
prematurely. Components suffering from stress fatigue can fail suddenly, causing loss of control or
serious injury.
CAUTION: RIDING IN WET WEATHER
It is recommended that you do not ride your Raptor in wet weather, as the electronic components of the
hoverboard may be damaged if exposed to water. Stopping distances can be longer in wet conditions than
in dry conditions.
1. This product is strictly forbidden to be used on roads and highways unless your local laws state otherwise.
You must wear a safety helmet, knee and elbow pads, and other necessary protective gear when riding your
Raptor.
2. Due to the nature of this product, the assembly pieces should be checked before every ride to avoid an
accident while riding.
3. Do not make a sharp turns, as you may drift and overturn the Raptor, which can result in injury to yourself
and/or damage the unit.
4. Do not operate near swimming pools or other bodies of water.

17
The first rule of safe riding is to use common sense. The Raptor cannot protect you in a crash, against impact,
or from loss of control the way a car can. The Raptor can tip over sideways or pitch you over the front wheel
if you don’t ride it properly. Please read the following safety precautions to operate your Raptor safely.
Different localities and countries have different laws governing riding on public roads, and you should check
with local officials to ensure you are complying with these laws.
Hover-1 is not liable for tickets or violations given to riders who do not follow these regulations.
• For your safety, always wear a helmet that meets CPSC or CE safety standards. In the event of an accident,
a helmet can protect you from serious injury and in some cases, even death.
• Obey all local laws, stop signs, pedestrian crosswalks, etc.
• If you are riding with other riders, maintain a safe distance between each other to avoid collisions.
• Ride defensively; expect the unexpected.
• Give pedestrians the right-of-way.
• Do not ride too close to pedestrians. Alert them if you intend to pass them from behind.
• Slow down at all street intersections and look to the left and right before crossing.
•Obey all traffic signals.
• Always use proper hand signals for turning and stopping. Give signals 100 ft before stopping or turning and
always return both hands to the handlebars before stopping or turning.
• Watch for cars when pulling into traffic and watch for the sudden opening of car doors.
• Avoid potholes, drainage grates, or other hazards.
• Be careful when riding on soft road edges, gravel, sand and uneven surfaces. Ride slowly and avoid quick
turns when riding on these surfaces.
• Never hitch onto other vehicles.
• Do not attempt any stunts or tricks with the Raptor. Do not race in traffic.
• Do not weave in and out of traffic or swerve from side to side.
• A crash can put extraordinary stress on Raptor’s components, possibly causing them to fatigue
prematurely. Components suffering from stress fatigue can fail suddenly, causing loss of control or
serious injury.
CAUTION: RIDING IN WET WEATHER
It is recommended that you do not ride your Raptor in wet weather, as the electronic components of the
hoverboard may be damaged if exposed to water. Stopping distances can be longer in wet conditions than
in dry conditions.
1. This product is strictly forbidden to be used on roads and highways unless your local laws state otherwise.
You must wear a safety helmet, knee and elbow pads, and other necessary protective gear when riding your
Raptor.
2. Due to the nature of this product, the assembly pieces should be checked before every ride to avoid an
accident while riding.
3. Do not make a sharp turns, as you may drift and overturn the Raptor, which can result in injury to yourself
and/or damage the unit.
4. Do not operate near swimming pools or other bodies of water.
WARNING
To reduce the risk of injury, adult supervision is required.
Never use in roadways, near motor vehicles, on or near
steep inclines or steps, near swimming pools, or other
bodies of water. Always wear shoes, and never allow
more than one rider at a time.

18
RIDING YOUR RAPTOR
Ensure your Raptor is fully assembled and correctly attached to your hoverboard with all straps, screws, and
nuts secured in place. Ensure your hoverboard is properly maintained as well. Failure to do so may result in
damage to the unit, serious bodily harm, or death.
After reviewing the pre-ride checklist, follow the steps below to begin riding your Raptor.
1. Turn on your hoverboard.
2. Sit comfortably in the Raptor seat.
2. Place your feet on the foot rests.
3. Firmly grip both handlebars and slowly push them downward simultaneously to move forward.
4. When riding, pull both handlebars upwards simultaneously to brake.
5. To ride in reverse, stop the hoverboard, then slowly pull both handlebars upwards simultaneously.
6. To turn left, push the right handlebar down and pull the left handlebar up.
7. To turn right, push the left handlebar down and pull the right handlebar up.

19
For warranty information, please visit us at www.hover-1.com
WARRANTY
Manufacturer: DGL Group, Ltd.
2045 Lincoln Highway, Edison, NJ 08817