HIK VISION DS-1100KI User manual

DS-1100KI Network Keyboard
User Manual
V 1.0

User Manual of DS-1100KI Network Keyboard
1
Preventive and Cautionary Tips
Before connecting and operating your keyboard, please be advised of the following tips:
•Ensure unit is placed in a well-ventilated, dust-free environment.
•Keep all liquids away from the keyboard.
•Please check the power supply to avoid the damage caused by voltage mismatch.
•Please make sure the keyboard work in the allowed range of temperature and humidity.
•Please keep the device horizontal and avoid the installation under severe vibration environment.
•The dust board will cause a short circuit after damping; Please dedust regularly for the board, connector,
chassis fan etc with brush.
•Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or
equivalent type only. Dispose of used batteries according to the instructions provided by the battery
manufacturer.

User Manual of DS-1100KI Network Keyboard
2
Table of Contents
Chapter1 Introduction........................................................................................................................ 3
1.1 Overview .............................................................................................................................. 3
1.2 Features................................................................................................................................ 3
1.3 Appearance .......................................................................................................................... 4
Chapter2 Keyboard Configuration...................................................................................................... 5
2.1 Keyboard Management........................................................................................................ 6
2.1.1 Network Settings....................................................................................................... 6
2.1.2 Hardware Settings ..................................................................................................... 6
2.1.3 Time Settings............................................................................................................. 7
2.1.4 Language ................................................................................................................... 7
2.1.5 Screen Verify ............................................................................................................. 7
2.1.6 Upgrade..................................................................................................................... 8
2.2 Device Management ............................................................................................................ 9
2.2.1 Add Device ................................................................................................................ 9
2.2.2 Modify/Delete Device ............................................................................................. 11
2.3 User Management ............................................................................................................. 11
2.3.1 Add User.................................................................................................................. 12
2.3.2 Related Device......................................................................................................... 12
2.3.3 Modify User Password and Delete User.................................................................. 13
2.3.4 Configure File .......................................................................................................... 13
2.4 Default................................................................................................................................ 13
2.5 Logout ................................................................................................................................ 14
2.6 Reboot................................................................................................................................ 14
2.7 Shutdown ........................................................................................................................... 14
Chapter3 Keyboard Operation ......................................................................................................... 15
3.1 Basic Operation .................................................................................................................. 15
3.1.1 Device List ............................................................................................................... 15
3.1.2 Input Settings .......................................................................................................... 16
3.1.3 Output Settings ....................................................................................................... 17
3.1.4 Macro Settings ........................................................................................................ 18
3.1.5 Aux Settings............................................................................................................. 19
3.1.6 Password Settings.................................................................................................... 19
3.1.7 Logout ..................................................................................................................... 19
3.1.8 Reboot..................................................................................................................... 20
3.1.9 Shutdown ................................................................................................................ 20
3.2 Shortcut Operation............................................................................................................. 20
3.2.1 Local Preview........................................................................................................... 21
3.2.2 Decoded Video Display on Monitor ........................................................................ 21
3.2.3 PTZ Control.............................................................................................................. 26
3.2.4 Aux Functions.......................................................................................................... 31
Appendix 1: Specifications ............................................................................................................... 33
Appendix 2: FTP Upgrade................................................................................................................. 34

User Manual of DS-1100KI Network Keyboard
3
Chapter1 Introduction
1.1 Overview
DS-1100KI Network Keyboard can be used to control the speed dome and the display of decoded video on TV
wall, as well as support 1 channel of video view at up to 1080P resolution. It is easy to operate and configure
settings.
1.2 Features
Hardware
7’’ TFT touch screen at 800×480 resolution;
3-axis joystick;
Shortcut keys for dome control, setting and callup of preset, patrol and pattern;
Shortcut keys for playback operation;
Shortcut keys for input group and output group;
Shortcut keys for wiper and light control operation.
Software
Administrator and operator user management;
Support upgrade by U-flash disk;
Auto searching connected devices in the same network area;
Support 15 operators, and each user is allowed to operate 256 devices with up to 4096 channels;
Import and export of keyboard parameters;
Macro command operation;
Backup of record files to U-flash disk;
Voice talk.
Decoding Capability
Provide 1-ch video decoding and local decoding;
Support standard MPEG4, private H.264 and standard H.264 encoding formats;
Decoding at up to 1080P resolution.
Display of Decoded Video on Monitor
Display of decoded camera on selected window;
Display of decoded camera group on selected window;
Sequence display of decoded camera group on monitor;
Sequence display of decoded camera group on monitor group.

User Manual of DS-1100KI Network Keyboard
4
1.3 Appearance
Front View:
Interface Description:

User Manual of DS-1100KI Network Keyboard
5
Chapter2 Keyboard Configuration
Note: Please use the user name admin to log in the system for the first time.
After keyboard startup,
enter the user login
interface. Select the user name to admin and input
the password of 12345. Click Login to enter the
admin main interface.
Input method shift:
Click the tab on the soft keyboard to enter
the interface for inputting the English letters, and
the
can be used to switch the
uppercase/lowercase.
Click the tab on the soft keyboard to enter
the interface for inputting the numerals.

User Manual of DS-1100KI Network Keyboard
6
2.1 Keyboard Management
Click Keyboard on the admin main interface to enter the keyboard management menu.
2.1.1 Network Settings
Configure the network settings of the keyboard,
including the Port, IP address, Subnet Mask and
Default Gateway, and finally click Apply to save the
settings.
Note: Make sure the DHCP is supported by the router
before enabling the function.
2.1.2 Hardware Settings
Key Sound/Alarm Sound/Key Light
: Click the
corresponding checkbox to
to enable the
function, or remain it as to disable the function.
Key Lock Timeout, Scr-close Timeout: Use the or
to decrease or increase the key lock timeout and
the screen-close timeout, with the max. value of 10s
and the min. value of 0s.
Transparency: Click to select the value from the
drop-down menu, with the 3: 1, 1: 1, 1: 3and non
transparent optional.
Note: The Transparency refers to the contrast of the
local decoded video and menu, and is valid only for the
local live view.
Mouse Speed: Select the mouse speed to level 0~2 or
1~3.
Brightness: Select the screen brightness to level 0~3.
Click Apply to save the settings.

User Manual of DS-1100KI Network Keyboard
7
2.1.3 Time Settings
Date: Click to select the date from the calendar.
Time: Click or to decrease or increase the time
value.
Click Apply to save the settings.
2.1.4 Language
Language: Click to select the option from the
drop-down menu.
Click Apply to save the setting.
2.1.5 Screen Verify
In order to use the touch screen correctly, it needs to
be calibrated properly.
Click Verify to start the calibration of touch screen
positioning. The system will pop up the Attention
message. Click Yes to continue the calibration.

User Manual of DS-1100KI Network Keyboard
8
Use the touch pen to click the three spots marked as
“+” by following the hints and then the system will pop
up the attention “Screen verify successfully”, click OK to
finish the operation.
2.1.6 Upgrade
FTP Upgrade: input the address of the FTP server and
then click FTP Upgrade to operate the upgrade.
Note: User must create the FTP server connection first
by TFTP or WFTP in PC before operating the FTP
upgrade. Please refer to Appendix2 for the upgrading.
If the upgrading is failed, the corresponding error
message box will be popped up.
Note: When the upgrading is successful, the keyboard
will restart automatically to complete the upgrade.
USB Upgrade: Insert the U flash disk to the USB
interface and then click USB Upgrade to enter the USB
upgrade interface. Select the upgrade file from the disk
and finally click Upgrade to start upgrading.
Note: The upgrade file must be digicap.dav.

User Manual of DS-1100KI Network Keyboard
9
If the upgrading is failed, the corresponding error
message box will pop up.
Note: When the upgrading is successful, the keyboard
will restart automatically to complete the upgrade.
2.2 Device Management
Click Device on the admin main interface to enter the
device management menu.
2.2.1 Add Device
Auto Search: Click Auto Search button at the upper left
corner to enter the “Device-Auto Search” interface.
Select the start IP and end IP of the device to be
searched, and then click Search to start searching. After
the searching is completed, all devices searched out
and their information will be displayed in the list below.
Select the device from the list, input its user name and
password, and then click Add to add it to the system.
Note: Only the device that is in the same network area
with the keyboard can be searched out by the
keyboard.
Status: In the status bar, the icon indicates the
device is not added, indicates the device is failed
to be added, and the
indicates the device is
successfully added.

User Manual of DS-1100KI Network Keyboard
10
User can also select multiple devices to be added each
time.
If the adding is failed, in the status bar it will display
in . If the adding is successful, it will display in .
Note: The devices for bulk adding must have the same
user name and password.
After having added the devices, click Return to return
to the “Device-List Management” interface, where user
can view the information of added devices.
Add Device: Click Add Device to enter the “Add Device”
interface. Input the device name, device IP, port, user
name and password, and then click Add to add the
device.
If the input message is incorrect or the device is offline,
the message box “Add Device failed” will pop up.

User Manual of DS-1100KI Network Keyboard
11
2.2.2 Modify/Delete Device
Modify Device: Click to enter the Modify Device”
interface. User is allowed to modify the device name,
port, user name and password. Finally, click Modify to
modify the device information.
Note: The user name and password here refer to that
are used for to log in the device from keyboard.
Delete Device: Click to delete the added device from the system.
2.3 User Management
The keyboard user includes the admin
and the
operator.
The admin
user is authorized with the following
operation permissions:
1. Add a maximum of 15 operators;
2. Configure the keyboard parameters;
3. Add, modify and delete device;
4.
Add, modify and delete user, as well as assign
device for the user.
The operator user is allowed to operate the assigned
device only.
Up to 256 devices can be assigned for each operator.
Click User on t
he main interface to enter the user
management menu.

User Manual of DS-1100KI Network Keyboard
12
2.3.1 Add User
Add User: Click Add User to enter the Add User
interface. Input the user name, password and verify the
password. Finally, click Add to finish the adding of user.
2.3.2 Related Device
In the User Management interface, click to enter
the “User-Device” interface.
Add Device: Click Add Device to enter the “User-Add
Device” interface. Select the device and then click the
checkbox to add it.
Delete Device: Enter the “User-Device” interface, and
click to delete the added device.

User Manual of DS-1100KI Network Keyboard
13
2.3.3 Modify User Password and Delete User
Modify User Password: In the “User Management”
interface, user can click to modify the user
password.
Delete User: Click to delete the selected user.
2.3.4 Configure File
Click Config on the admin main interface to enter the file Export/Import Configuration menu.
Import Configuration: Insert the U flash disk to the USB
interface on the keyboard and enter the disk to select a
file and then click Import to import the configuration
file.
Export Configuration: Insert the U flash disk to the USB
interface on the keyboard and then click Export to
export the configuration file named in kbCfg.bin.
If the imported configuration file is not correct, the
message box “Configuration file incompatible” will pop
up.
2.4 Default
Click Default on the admin main interface, the message
box “Do you want to restore default parameters” will
pop up. Click Yes to continue the operation, or No to
cancel the operation.

User Manual of DS-1100KI Network Keyboard
14
2.5 Logout
Click Logout on the admin main interface, the message
box “Logout Now?” will pop up. Click Yes to confirm the
logout, or No to cancel the operation.
After logout, the system will return to the User Login
interface.
2.6 Reboot
Click Reboot on the admin main interface, the message
box “Are you sure you want to reboot now?” will pop
up. Click Yes to confirm the reboot, or No to cancel the
operation.
2.7 Shutdown
Click Shutdown on the admin main interface, the
message box “Are you sure you want to shut down
now?” will pop up. Click Yes to confirm the shutdown,
or No to cancel the operation.

User Manual of DS-1100KI Network Keyboard
15
Chapter3 Keyboard Operation
3.1 Basic Operation
In the User Login
interface, select the user name
(operator) and password, and then click Login to enter
the operator main interface.
Enter the operator main interface.
3.1.1 Device List
Click the Device List on the main interface to enter the
Device List menu.
The list will display all devices which can be controlled
by the current login user.

User Manual of DS-1100KI Network Keyboard
16
3.1.2 Input Settings
Click Input Set on the
main interface to enter the
Input Settings menu.
The list has displayed all device channels which can be
controlled by the current login user.
Note: The channel name shown in the Monitor Name is
obtained from the corresponding channel of device.
Modify Monitor:In the “Input Settings-Input List”
menu, click to modify the channel name of the
device.
Note: The monitor No. should be set uniquely from 0 to
9999.
Input Group: Click Input Group to enter the “Input
Settings-Input Group” interface. Click to select the
group No. from the drop-down menu.
Note: Up to 16 groups can be configured.
Delete Monitor: User can click to delete the added
monitor.
Add Monitor: Click Add Monitor to enter the “Input
Settings-Add Monitor” menu.
Select the monitor by clicking the checkbox and then
click Add.
In the “Input Settings-Input Group” interface, the added
monitors can be displayed in the list.

User Manual of DS-1100KI Network Keyboard
17
3.1.3 Output Settings
Click Output Set on the
main interface to enter the
Output Settings menu.
Modify Monitor:In the “Output Settings-Output List”
menu, click to modify the channel name of the
device.
Note: The monitor No. should be set uniquely from 0 to
9999.
Output Group: Click Output Group
to enter the
“Output Settings-Output Group” interface. Click to
select the group No. from the drop-down menu.
Note: Up to 16 groups can be configured.
Delete Output:User can click to delete the added
output interface
Add Output: Click Add Output to enter the “Output
Settings-Add Output” menu.
Select the output by clicking the checkbox and then
click Add.
In the “Output Settings-Output Group” interface, the
added outputs can be displayed in the list.

User Manual of DS-1100KI Network Keyboard
18
3.1.4 Macro Settings
The macro command can be used for operating a series of continuous actions in sequence.
Operation: Press the “Num+MAC” keys to call the programmed macro command.
Click Macro Set on the main interface to enter the
Macro Settings menu.
Add Macro: Click Add Macro to enter the “Macro
Setting-Add Macro” interface. Edit the macro name,
and press the command keys on the keyboard to enter
the text box below. Finally, click Add to add the current
macro command.
Note:
1.Up to 128 macro commands can be added.
2.The local decoding and preview operation is not
supported currently.
View Macro: In the Macro Settings interface, click
to view the added macro command.
Run Macro: Click in the list to run the macro
command, or directly click “Num+MAC” keys on the
interface to call the macro command.
Delete Macro: User can click to delete the added
macro command.

User Manual of DS-1100KI Network Keyboard
19
3.1.5 Aux Settings
Click Aux Set on the main interface to enter the Aux
Settings menu.
The Aux Key 1 and Aux Key 2 correspond to the AUX1
and AUX2 keys on the keyboard respectively. The Aux
key operation can be set to Voice Talk or Picture Catch.
Click to select the Aux function to be realized, and
then click OK to save the settings.
3.1.6 Password Settings
Click PW Set on the
main interface to enter the
Password Settings menu.
It is allowed to modify the password for the current
login user.
After having entered the new password, click OK to
finish the password modification.
3.1.7 Logout
Click Logout on the main interface, the message box
“Logout Now?” will pop up. Click Yes to confirm the
logout, or No to cancel the operation.
After logout, the system will return to the User Login
interface.