HIK VISION DS-D5032FL/D User manual

32 and 42-inch LCD Unit User Manual
DS-D5032FL
User Manual
UD00253N

32 and 42-inch LCD Unit User Manual
i
User Manual
About this Manual
This Manual is applicable to 32 and 42-inch LCD Unit.
The Manual includes instructions for using and managing the product. Pictures, charts, images and all
other information hereinafter are for description and explanation only. The information contained in
the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find
the latest version in the company website
Please use this user manual under the guidance of professionals.
Legal Disclaimer
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL
BE WHOLLY AT YOUR OWN RISKS. OUR COMPANY SHALL NOT TAKE ANY
RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER
DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION,
OR OTHER INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY WILL PROVIDE
TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS
IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT
YOUR USE CONFORMS THE APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE
IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE
LAW, THE LATER PREVAILS.

32 and 42-inch LCD Unit User Manual
ii
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired
operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE"
and comply therefore with the applicable harmonized European standards listed
under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC.
2002/96/EC (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated collection points. For more
information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed
of as unsorted municipal waste in the European Union. See the product documentation
for specific battery information. The battery is marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper
recycling, return the battery to your supplier or to a designated collection point. For
more information see: www.recyclethis.info.

32 and 42-inch LCD Unit User Manual
iii
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property
loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Warnings
Proper configuration of all passwords and other security settings is the responsibility of the
installer and/or end-user.
In the use of the product, you must be in strict compliance with the electrical safety
regulations of the nation and region. Please refer to technical specifications for detailed
information.
Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited
Power Source with 100 to 240 VAC or 12 VDC according to the IEC60950-1 standard.
Please refer to technical specifications for detailed information.
Do not connect several devices to one power adapter as adapter overload may cause
over-heating or a fire hazard.
Please make sure that the plug is firmly connected to the power socket.
If smoke, odor or noise rise from the device, turn off the power at once and unplug the
power cable, and then please contact the service center.
Warnings Follow these safeguards
to prevent serious injury or death.
Cautions Follow these precautions to
prevent potential injury or material
damage.

32 and 42-inch LCD Unit User Manual
iv
Table of Content
Chapter 1 Introduction...............................................................................................................5
1.1 Main Features...................................................................................................................5
1.2 Power Supply Connection................................................................................................ 6
Chapter 2 Device Interfaces....................................................................................................... 7
2.1 DS-D5032FL/D and DS-D5042FL/D............................................................................... 7
2.2 DS-D5032FL/S and DS-D5042FL/S................................................................................7
2.3 DS-D5032FL and DS-D5042FL....................................................................................... 8
Chapter 3 Panel Buttons............................................................................................................. 9
Chapter 4 Remote Control .......................................................................................................10
Chapter 5 Basic Operation....................................................................................................... 12
5.1 Input Source................................................................................................................... 12
5.2 Main Menu..................................................................................................................... 13
5.2.1 Image Parameters......................................................................................................13
5.2.2 Overscan ................................................................................................................... 17
5.2.3 System Information and Maintenance.......................................................................18
5.2.4 Settings .....................................................................................................................20
5.3 USB Menu...................................................................................................................... 25
Chapter 6 Appendix: ................................................................................................................26
6.1 Specifications.................................................................................................................26
6.2 Structure Diagram.......................................................................................................... 30

32 and 42-inch LCD Unit User Manual
5
IntroductionChapter 1
1.1Main Features
8 bit/10 bit 2-ch LVDS(1920×1080) HD display
3-D digital comb filter
True color OSD and user-friendly operation menu
Mstar ACE-5 auto color and image enhancement engine, improve the image contrast, details,
color of skin and edges, and so on
Programmable 12-bit RGB gamma correction technology
1-ch HDMI with1.3 input interface
HDCP 1.2
Spread-spectrum technology reduces EMI radiation
Adopt 3D noise reduction technology
High definition JPEG decoding
BNC interface with professional monitoring standard supports 1-ch BNC video input
Support multimedia playing: text, image, audio, video, and so on
Signal source decoding (DS-5032FL/D and DS-D5042FL/D)
SDI signal input and output (DS-5032FL/S and DS-D5042FL/S)

32 and 42-inch LCD Unit User Manual
6
1.2Power Supply Connection
Insert the power adapter into the well-grounded socket and turn the power switch on.
Figure 1.1 Power Adapter
Power Adapter
Input Voltage
100 to 240VAC
Output Voltage
12 V
Output Current
3.33 A
Output Power
40 W
Power adapter shall operate within input specification from 100V AC to 240V AC or
provide automatic switching between high line and low line input ranges.
Turn off the main power switch of the LCD unit, and pull the plug from the power outlet
if the LCD unit will not be used for a long time.
Never connect the device to a DC power.

32 and 42-inch LCD Unit User Manual
7
Device InterfacesChapter 2
2.1DS-D5032FL/D and DS-D5042FL/D
Figure 2.1 Rear Panel (1)
Table 2. 1 Interface Description
Interfaces
Description
FIBER
Optical fiber interface
LAN
Network interface
HDMI IN
HDMI digital signal input
DVI IN
DVI digital signal input
VGA IN
VGAanalog signal input
CVBS/IN
Composite video input
USB
USB interface
RS232 IN
Serial port input
AUDIO IN
Audio input
AUDIO OUT
Audio output
2.2DS-D5032FL/S and DS-D5042FL/S
Figure 2. 1 Rear Panel (2)

32 and 42-inch LCD Unit User Manual
8
Table 2. 2 Interface Description
Interfaces
Description
SDI IN
SDI signal input
SDI OUT
SDI signal output
HDMI IN
HDMI digital signal input
DVI IN
DVI digital signal input
VGA IN
VGAanalog signal input
CVBS/IN
Composite video input
USB
USB interface
RS232 IN
Serial port input
AUDIO IN
Audio input
AUDIO OUT
Audio Output
2.3DS-D5032FL and DS-D5042FL
Figure 2. 2 Rear Panel (3)
Table 2. 3 Interface Description
Interfaces
Description
HDMI IN
HDMI digital signal input
DVI IN
DVI digital signal input
VGA IN
VGAanalog signal input
CVBS/IN
Composite video input
USB
USB interface
RS232 IN
Serial port input
AUDIO IN
Audio input
AUDIO OUT
Audio output

32 and 42-inch LCD Unit User Manual
9
Panel ButtonsChapter 3
Buttons on lower right corner of the LCD unit panel are shown as the Figure 3.1.
Figure 3.1 Buttons on the Display Unit
Table 3. 1 Button Description
Buttons
Description
SOURCE
Press to show source menu
MENU
Press to show Menu
UP/DOWN
Press to move the cursor up/down
LEFT/RIGHT
Press to move the cursor left/right
POWER
Press to confirm/start up; hold down to shut down

32 and 42-inch LCD Unit User Manual
10
Remote ControlChapter 4
A remote control is attached when you purpose the LCD unit and you can use the remote control to
control LCD unit. For detailed button function, refer to Table 4.1 Button Description.
Figure 4. 1 Remote Control

32 and 42-inch LCD Unit User Manual
11
Table 4. 1 Button Description
Name
Function
Name
Function
POWER
Turn on/off the LCD
unit
MENU
Menu
TEST
Aging test
SOURCE
Input source menu
MUTE
Turn off/on the sound
CH
Reserved
Number 0-9
Numerical button
PLAY
Play/Pause
FREEZE
Freeze the screen
STOP
Stop
PIC
Image mode shortcut
PREV/NEXT
Previews/Next
INFO
System information
LIST
Playing list
LIGHT
Lighting mode
REPEAT
Replay
Direction Key
Up/Down, Left/Right
L/R
Left/Right
channel/stereo
OK
Confirm/Enter
RETURN
Back to the previous
menu
+VOL-
Volume adjustment

32 and 42-inch LCD Unit User Manual
12
Basic OperationChapter 5
5.1Input Source
Steps:
1. Turn on the LCD unit when the power supply is on, after the input source is confirmed.
2. Press SOURCE button on the remote control to show the input source menu.
3. Press direction button to select the input source and press OK to finish the input source
selection.
DS-D5032FL and DS-D5042FL include 5 input signal sources:AV, HDMI, DVI, PC-RGB, and
USB.
Input Source
AV
HDMI
DVI
PC-RGB
USB
Figure 5. 1 Input Signal Source (1)
DS-D5032FL/D and DS-D5042FL/D include 6 input signal sources: AV, HDMI, DVI,
PC-RGB, USB, and IP.
Input Source
AV
HDMI
DVI
PC-RGB
USB
IP
Figure 5. 2 Input Signal Source (2)

32 and 42-inch LCD Unit User Manual
13
DS-D5032FL/S and DS-D5042FL/S include 6 input signal sources: AV, HDMI, DVI, PC-RGB,
USB and SDI.
Input Source
AV
HDMI
DVI
PC-RGB
USB
SDI
Figure 5. 3 Input Signal Source (3)
5.2Main Menu
5.2.1 Image Parameters
Picture Mode
Purpose:
You can adjust the picture parameters by switching image modes and adjusting the values of contrast,
brightness, color, sharpness and hue.
Steps:
1. Press Menu button to enter the main menu interface shown as below (set default as Picture
Mode).
2. Press OK button to enter the Picture Mode ◄Normal ►interface. (set default as Standard)
3. Press ◄or ►to switch it between Dynamic, Soft and Custom Mode. It applies for adjusting
contrast, brightness, color and other parameters.
Contrast and brightness: Under Custom mode, press ◄or ►to set the contrast
ranging from 0 to 100.
Color, sharpness and hue: Under Custom mode, press ◄or ►to set the contrast
ranging from 0 to 100.(Color, sharpness, hue are not adjustable when the input
source is analog)
Gray indicates that under current mode or current input source condition it is not
adjustable; white indicates that it is adjustable.

32 and 42-inch LCD Unit User Manual
14
4. Press Menu button to return to the main menu after finishing the adjustment.
Picture Mode
Light Mode
Sound Setting
VGA Parameter
Picture Mode Custom
Contrast 51
Brightness 53
Color 50
Sharpness 50
Hue 50
Figure 5. 4 Picture Mode
Light Mode
Purpose:
You can select different light modes according to different conditions.
Steps:
1. Press Menu button to enter the main menu interface.
2. Select Light Mode and press OK key to enter the Light Mode ◄Normal►interface. (set
default as Normal)
3. Press ◄or ►to switch it between Normal, Day 1 to 3 and Night 1 to 3.
Normal Mode: Under normal sunlight;
Day Mode: Under strong sunlight with Day 1, Day 2 and Day 3, three modes
available.
Night Mode: Under low light, with Night 1, Night 2 and Night 3, three modes
available.
4. Press Menu button to return to the main menu after finishing the adjustment.

32 and 42-inch LCD Unit User Manual
15
Picture Mode
Light Mode
Sound Setting
VGA Parameter
Light Mode Normal
Figure 5. 5 Light Mode
Sound Settings
Purpose:
You can switch the mute On/Off and adjust the sound value and balance.
Steps:
1. Press Menu button to enter the main menu interface.
2. Select Sound Setting and press OK button to enter the MUTE ◄Off►interface.
3. Press ◄or ►to switch the mute On/Off.
4. Select Volume Value and press ◄or ►to adjust the volume value.
5. Select Balance and press ◄or ►to adjust the sound balance.
Volume Value: the volume ranges from 0 to100.
Balance: the balance ranges from -50 to 50.
6. Press Menu button to return to the main menu after finishing the adjustment.

32 and 42-inch LCD Unit User Manual
16
Picture Mode
Light Mode
Sound Setting
VGA Parameter
MUTE Off
Volume Value 0
Balance 0
Figure 5. 6 Sound Setting
VGAParameter
Purpose:
When the input source is selected as VGA, you can adjust the VGA parameters including H position,
V Position, clock and phase.
Steps:
1. Press Menu button to enter the main menu interface
2. Select VGAParameter and press OK button to enter the VGAparameter setting interface.
(You can select Auto Adjust and press ◄or ►to adjust the VGAparameters automatically or
adjust it manually)
3. Select H Position and press ◄or ►to adjust the H Position
4. Select V Position and press ◄or ►to adjust the V position.
5. Select Clock and press ◄or ►to adjust the clock.
6. Select Phase and press ◄or ►to adjust the phase.
The range of the adjustment ranges from 0 to100.
7. Press Menu button to return to the main menu after finishing the adjustment.

32 and 42-inch LCD Unit User Manual
17
Picture Mode
Light Mode
Sound Setting
VGA Parameter
Auto Adjust
H Position 51
V Position 50
Clock 50
Phase 7
Figure 5. 7 VGA Parameters
5.2.2 Overscan
Purpose:
When there is a black border, you can shield the border for the better image quality, and you can
adjust the overscan value via pressing up/down/left/right buttons.
Steps:
1. Press Overscan key to enter the Overscan ◄On ►interface
2. Press ◄or ►to switch the overscan On/Off.
3. Select the edge you want to shield.
4. Press ◄or ►to adjust the value of the overscan on certain edge.
The value of overscan is the pixel value of certain edge.
The value ranges from 0 to 100.
5. Press Menu button to return to the main menu after finishing the adjustment.

32 and 42-inch LCD Unit User Manual
18
L/R Back OK
Overscan
Overscan On
Left Edge 0
Right Edge 0
Top Edge 0
Bottom Edge 0
Figure 5. 8 Overscan
5.2.3 System Information and Maintenance
Maintenance
Steps:
1. To update the software, insert the USB driver to the interface on the rear panel of the device.
2. Press Maintenance button to enter the Maintenance interface
3. Select the Update (USB) to update it.
4. To reset the parameters, select User Restore and reset the parameters of picture, sound and other
parameters to the default value.

32 and 42-inch LCD Unit User Manual
19
Maintenance
Temp Monitor
Information
Update (USB) Select
User Restore Select
Figure 5. 9 System Maintenance
For further information about downloading upgrade program and USB driver usage,
please contact your dealer or the nearest service center.
5. Press MENU button to return to the main menu after finishing the adjustment.
Temperature Monitor
Purpose:
Enable the overheat alarm and once the board temperature is too high, an alarm prompt appears on
the screen.
Steps:
1. Select Temp Monitor and press OK button to enter the OverheatAlarm ◄On ►interface on
the right.
2. Press ◄or ►to switch the Overheat Alarm On/Off.
3. When the Overheat Alarm is switched to◄On ►, the overheat alarm function is enabled shown
as the Figure 5.4 Temperature Monitor.
4. Select Alarm Temp (°C) and press ◄or ►to adjust the alarm temperature value.
5. Press MENU button to return to the main menu after finishing the adjustment.