HIK VISION DS-2CD4312F-I User guide

1
Camera
Network Dome Camera
Quick Operation Guide
UD.6L0201B1228A01

Network Dome Camera·Quick Operation Guide
1
1
Thank you for purchasing our product. If there are any questions, or
requests, please do not hesitate to contact the dealer.
About This Document
This manual applies to the following camera models.
Model
Model
DS-2CD4312F-(I)(Z)(H)(S)
DS-2CD4312FWD-(I)(Z)(H)(S)
DS-2CD4324F-(I)(Z)(H)(S)
DS-2CD4332FWD-(I)(Z)(H)(S)
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without notice.
The updates will be added to the new version of this manual. We will
readily improve or update the products or procedures described in
the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of this
product. UL has only tested for fire, shock or casualty hazards as
outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certification
does not cover the performance or reliability of the security or
signaling aspects of this product. UL MAKES NO REPRESENTATIONS,
WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING
RELATED FUNCTIONS OF THIS PRODUCT.
0500081030923

Network Dome Camera·Quick Operation Guide
2
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the Low Voltage Directive 2006/95/EC, the
EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.

Network Dome Camera·Quick Operation Guide
3
3
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. For more information
see: www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more information
see: www.recyclethis.info

Network Dome Camera·Quick Operation Guide
4
4
Safety Instruction
These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings
are neglected.
Cautions: Injury or equipment damage may occur if any of the
cautions are neglected.
Warnings
●In the use of the product, you must be in strict compliance with
the electrical safety regulations of the nation and region. Please
refer to technical specifications for detailed information.
●Input voltage should meet both the SELV (Safety Extra Low
Voltage) and the Limited Power Source with 24 VAC or 12 VDC
according to the IEC60950-1 standard. Please refer to technical
specifications for detailed information.
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.

Network Dome Camera·Quick Operation Guide
5
5
●Do not connect several devices to one power adapter as
adapter overload may cause over-heating or a fire hazard.
●Please make sure that the plug is firmly connected to the power
socket. When the product is mounted on wall or ceiling, the
device shall be firmly fixed.
●If smoke, odor or noise rise from the device, turn off the power
at once and unplug the power cable, and then please contact
the service center.
Cautions
●Make sure the power supply voltage is correct before using the
camera.
●Do not drop the camera or subject it to physical shock.
●Do not touch sensor modules with fingers. If cleaning is
necessary, use clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period,
please replace the lens cap to protect the sensor from dirt.
●Do not aim the camera at the sun or extra bright places.
Blooming or smearing may occur otherwise (which is not a
malfunction), and affect the endurance of sensor at the same
time.
●The sensor may be burned out by a laser beam, so when any
laser equipment is in using, make sure that the surface of
sensor will not be exposed to the laser beam.

Network Dome Camera·Quick Operation Guide
6
6
●Do not place the camera in extremely hot, cold (the operating
temperature shall be-30℃~+60℃,or -40°C ~ 60°C if the camera
model has an “H” in its suffix), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
●To avoid heat accumulation, good ventilation is required for
operating environment.
●Keep the camera away from liquid while in use.
●While in delivery, the camera shall be packed in its original
packing, or packing of the same texture.
●Regular part replacement: a few parts (e.g. electrolytic
capacitor) of the equipment shall be replaced regularly
according to their average enduring time. The average time
varies because of differences between operating environment
and using history, so regular checking is recommended for all
the users. Please contact with your dealer for more details.
●Improper use or replacement of the battery may result in
hazard of explosion. Replace with the same or equivalent type
only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.
●If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance.)

Network Dome Camera·Quick Operation Guide
7
7
Table of Contents
1 Appearance Description ................................................................. 8
1.1 Overview of Type I Dome Camera ................................... 8
1.2 Overview of Type II Dome Camera .................................. 9
2 Installation.................................................................................... 11
2.1 Installation of Type I Dome Camera............................... 12
2.2 Installation of Type II Dome Camera.............................. 16
3 Setting the Network Camera over the LAN .................................. 20
4 Accessing via Web Browser .......................................................... 25

Network Dome Camera·Quick Operation Guide
8
8
Appearance Description1
Overview of Type I Dome Camera1.1
Overview (1) of Type I Dome CameraFigure 1-1
Overview (2) of Type II Dome CameraFigure 1-2
3
12
4
6
5
7
8
9
10

Network Dome Camera·Quick Operation Guide
9
9
Description of Overview (1~2)Table 1-1
No.
Description
No.
Description
1
Black Liner
6
Reset
2
Bubble
7
Power Cable
3
Mounting Base
8
10/100M Self-adaptive
Ethernet Interface
4
SD Card Slot
9
Lens
5
Video Out Interface
10
Audio/ Alarm Cables
Overview of Type II Dome Camera1.2
Overview of Type II Dome CameraFigure 1-3
56
8
1
2
3
4
9
7

Network Dome Camera·Quick Operation Guide
10
10
Description of Type II Dome CameraTable 1-2
No.
Description
No.
Description
1
Bubble
6
10/100M Self-adaptive
Ethernet Interface
2
SD Card Slot
7
Lens
3
Video Out Interface
8
Audio/Alarm Cables
4
Reset
9
Mounting Base
5
Power Cable
10
●The most distinguish difference between type I and type II dome
camera is type II dome camera has an internal PT (Pan and Tilt)
control unit, and you can adjust the pan and tilt angle of the
camera from the client software or via web browser.
●Press RESET about 10s when the camera is power on or rebooting
to restore the default settings, including the user name, password,
IP address, and the port No., etc.

Network Dome Camera·Quick Operation Guide
11
11
Installation2
Before you start:
●Make sure the device in the package is in good condition and all
the assembly parts are included.
●Make sure all the related equipment is power-off during the
installation.
●Check the specification of the products for the installation
environment.
●Make sure the power supply is matched with your required
voltage to avoid damage.
●If the product does not function properly, please contact your
dealer or the nearest service center. Do not disassemble the
camera for repair or maintenance by yourself.
●Make sure that the wall is strong enough to withstand three
times the weight of the camera.
For the camera that supports IR, you are required to pay attention to
the following precautions to prevent IR reflection:
●Dust or grease on the dome cover will cause IR reflection.
Please do not remove the dome cover film until the installation
is finished. If there is dust or grease on the dome cover, clean
the dome cover with clean soft cloth and isopropyl alcohol.

Network Dome Camera·Quick Operation Guide
12
12
●Make sure that there is no reflective surface too close to the
camera lens. The IR light from the camera may reflect back into
the lens causing reflection.
●The foam ring around the lens must be seated flush against the
inner surface of the bubble to isolate the lens from the IR LEDS.
Fasten the dome cover to camera body so that the foam ring
and the dome cover are attached seamlessly.
Installation of Type I Dome Camera2.1
Steps:
1. Drill the screw holes and the cable hole according to the supplied
drill template.
Drill TemplateFigure 2-1
2. Install the mounting base to the ceiling with the supplied screws.
Drill Tempalte
1
1
22
22
3
3
3
3
44
44
Screw Hole 3: for
Mounting Base
Hole A: for cables routed
through the ceiling
Code: 190600839

Network Dome Camera·Quick Operation Guide
13
13
Install the Mounting BaseFigure 2-2
3. Connect the corresponding power cable, network cable, audio
and alarm cables.
4. Install the dome drive to the mounting base.
Install the Dome DriveFigure 2-3
5. Adjust the surveillance angle.
Dome
Drive

Network Dome Camera·Quick Operation Guide
14
14
1). Loosen the lock screw besides the lens.
2). Hold the plastic plate and rotate the camera to adjust the
panning angle [0~350°].
3). Push the lens forward and backward to adjust the tilting angle
[0~80°]
4). Rotate the lens to adjust the azimuth angle of the camera
[0~350°]
5). Tighten the lock screw.
3-axis AdjustmentFigure 2-4
6. Adjust the Lens
1). Connect the VIDEO OUT interface of the camera to the
debugging monitor.
2). Set the iris type to MANUAL first.
3). Adjust the No.2 Zoom Lever (T~W) to select a proper angle of
view.
Tilt 0~80° Pan 0~350°
Rotation 0~350°

Network Dome Camera·Quick Operation Guide
15
15
4). Adjust the No.1 Focus Lever (F~N) to obtain a perfect image on
the monitor.
5). Set the iris type as MANUAL if the environment has a good and
stable illumination, and set the iris type as AUTO if the
environment has a strong and changeable illumination.
Adjust the Focus and ZoomFigure 2-5
7. Fit the black liner back to the camera.
8. Align the bubble to camera and fix it by tightening the screws.
21

Network Dome Camera·Quick Operation Guide
16
16
Install the Black Liner and BubbleFigure 2-6
Complete the InstallationFigure 2-7
Installation of Type II Dome Camera2.2
Steps:
1. Drill the screw holes and the cable hole according to the supplied
drill template.

Network Dome Camera·Quick Operation Guide
17
17
Drill TemplateFigure 2-8
2. Install the mounting base to the ceiling with the supplied screws.
Install the Mounting BaseFigure 2-9
3. Connect the corresponding power cable, network cable, audio
and alarm cables.
Drill Tempalte
1
1
22
22
3
3
3
3
44
44
Screw Hole 3: for
Mounting Base
Hole A: for cables routed
through the ceiling
Code: 190600839

Network Dome Camera·Quick Operation Guide
18
18
4. Install the dome drive to the mounting base.
Install the Dome DriveFigure 2-10
The surveillance angle of the camera is well- adjusted by default. If
the pan and tilt angle is required to adjusted according to the
different installation environment, you can view the camera after the
installation is completed. Please refer to the pan and tilt adjustment
interface below.
Pan and Tilt Adjustment InterfaceFigure 2-11
5. Install the bubble to complete the installation.

Network Dome Camera·Quick Operation Guide
19
19
Install the BubbleFigure 2-12