HIK VISION UD.6L0201B1295A01 User guide

1
Network Convert Camera
Quick Operation Guide
UD.6L0201B1295A01

Network Convert Camera·Quick Operation Guide
1
1
Thank you for purchasing our product. If there are any questions, or
requests, please do not hesitate to contact the dealer.
About This Document
This manual applies to the following camera models.
Model
DS-2CD6412FWD-10
DS-2CD6412FWD-20
DS-2CD6412FWD-30
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without notice.
The updates will be added to the new version of this manual. We will
readily improve or update the products or procedures described in
the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of this
product. UL has only tested for fire, shock or casualty hazards as
outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certification
does not cover the performance or reliability of the security or
signaling aspects of this product. UL MAKES NO REPRESENTATIONS,
WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING
RELATED FUNCTIONS OF THIS PRODUCT.
0501001040109

Network Convert Camera·Quick Operation Guide
2
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the Low Voltage Directive 2006/95/EC, the
EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.

Network Convert Camera·Quick Operation Guide
3
3
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal
waste in the European Union. See the product
documentation for specific battery information.
The battery is marked with this symbol, which
may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more information
see: www.recyclethis.info

Network Convert Camera·Quick Operation Guide
4
4
Safety Instruction
These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings
are neglected.
Cautions: Injury or equipment damage may occur if any of the
cautions are neglected.
Warnings
●In the use of the product, you must be in strict compliance with
the electrical safety regulations of the nation and region. Please
refer to technical specifications for detailed information.
●Input voltage should meet both the SELV (Safety Extra Low
Voltage) and the Limited Power Source with 24 VAC or 12 VDC
according to the IEC60950-1 standard. Please refer to technical
specifications for detailed information.
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.

Network Convert Camera·Quick Operation Guide
5
5
●Do not connect several devices to one power adapter as
adapter overload may cause over-heating or a fire hazard.
●Please make sure that the plug is firmly connected to the power
socket. When the product is mounted on wall or ceiling, the
device shall be firmly fixed.
●If smoke, odor or noise rise from the device, turn off the power
at once and unplug the power cable, and then please contact
the service center.
Cautions
●Make sure the power supply voltage is correct before using the
camera.
●Do not drop the camera or subject it to physical shock.
●Do not touch sensor modules with fingers. If cleaning is
necessary, use clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period,
please replace the lens cap to protect the sensor from dirt.
●Do not aim the camera at the sun or extra bright places.
Blooming or smearing may occur otherwise (which is not a
malfunction), and affect the endurance of sensor at the same
time.
●The sensor may be burned out by a laser beam, so when any
laser equipment is in using, make sure that the surface of
sensor will not be exposed to the laser beam.

Network Convert Camera·Quick Operation Guide
6
6
●Do not place the camera in extremely hot, cold (the operating
temperature shall be-30°C ~+60°C ,or -40°C ~ 60°C if the camera
model has an “H” in its suffix), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
●To avoid heat accumulation, good ventilation is required for
operating environment.
●Keep the camera away from liquid while in use.
●While in delivery, the camera shall be packed in its original
packing, or packing of the same texture.
●Regular part replacement: a few parts (e.g. electrolytic
capacitor) of the equipment shall be replaced regularly
according to their average enduring time. The average time
varies because of differences between operating environment
and using history, so regular checking is recommended for all
the users. Please contact with your dealer for more details.
●Improper use or replacement of the battery may result in
hazard of explosion. Replace with the same or equivalent type
only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.
●If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance.)

Network Convert Camera·Quick Operation Guide
7
7
Table of Contents
1 Appearance Description ................................................................. 8
2 Installation.................................................................................... 12
2.1 Installation of Block-Shaped Sensor Unit....................... 15
2.1.1 Concealed Mounting .......................................... 15
2.1.2 Exposed Mounting ............................................. 17
2.2 Installation of Cylindrical Sensor Unit............................ 19
2.3 Installation of Fixed Focal Unit ...................................... 21
3 Setting the Network Camera over the LAN .................................. 25
4 Accessing via Web Browser .......................................................... 30

Network Convert Camera·Quick Operation Guide
8
8
1Appearance Description
Camera Description
The overview of the network bullet camera is shown below:
The Covert Camera with Block-shaped Sensor UnitFigure 1-1
1
ALARM
RS232
RXDTXD GND IN1 1B1A
LAN(PoE)
DC12V
RESET
SD
VIN1
AUDIO
OUT
AUDIO
IN
234
56
7
89
11
10
12
13
14
15

Network Convert Camera·Quick Operation Guide
9
9
The Covert Camera with Cylindrical Sensor UnitFigure 1-2
The Covert Camera with Fixed Focal UnitFigure 1-3
1
ALARM
RS232
RXDTXD GND IN1 1B 1A
LAN(PoE)
DC12V
RESET
SD
VIN1
AUDIO
OUT
AUDIO
IN
234
56
7
89
11
10
12
16
17
18
1
ALARM
RS232
RXDTXD GND IN1 1B 1A
LAN(PoE)
DC12V
RESET
SD
VIN1
AUDIO
OUT
AUDIO
IN
234
56
7
89
11
10
12
19
20

Network Convert Camera·Quick Operation Guide
10
10
Description of the CameraTable 1-1
No.
Description
No.
Description
1
Main Unit
11
PoE & Network
2
Power Indicator LED
12
Mounting Rail
3
Status Indicator LED
13
Block-Shaped Sensor
Unit
4
Link Indicator Led
14
Decorative Cover
5
Audio Interface
15
Straight Mounting
Bracket
6
RJ-12 Cable
16
Cylindrical Sensor Unit
7
Micro SD Card Slot
17
RJ-12 Interface
8
RESET Button
18
Round Rail Mounting
Bracket
9
RS-232 &Alarm
Interface
19
Fixed Focal Camera
10
Power Interface
20
Ceiling Mounting
Bracket
LED IndicatorTable 1-2

Network Convert Camera·Quick Operation Guide
11
11
LED
Color&
Status
Indicator
POWER
Solid red
On normal operation
Unlit
Power Off
STATUS
Solid green
Camera works properly
Unlit
Camera does not work
properly.
LINK
Flashing
amber
Network connection is
functioning properly
Unlit
No network connection

Network Convert Camera·Quick Operation Guide
12
12
2Installation
Before you start:
Make sure the device in the package is in good condition and all
the assembly parts are included.
Make sure all the related equipment is power-off during the
installation.
Check the specification of the products for the installation
environment.
Make sure the power supply is matched with your required
voltage to avoid damage.
If the product does not function properly, please contact your
dealer or the nearest service center. Do not disassemble the
camera for repair or maintenance by yourself.
Make sure that the wall is strong enough to withstand three times
the weight of the camera.
For the camera that supports IR, you are required to pay attention to
the following precautions to prevent IR reflection:
●Dust or grease on the dome cover will cause IR reflection.
Please do not remove the dome cover film until the installation
is finished. If there is dust or grease on the dome cover, clean
the dome cover with clean soft cloth and isopropyl alcohol.

Network Convert Camera·Quick Operation Guide
13
13
●Make sure that there is no reflective surface too close to the
camera lens. The IR light from the camera may reflect back into
the lens causing reflection.
●The foam ring around the lens must be seated flush against the
inner surface of the bubble to isolate the lens from the IR LEDS.
Fasten the dome cover to camera body so that the foam ring
and the dome cover are attached seamlessly.
Steps:
Fix the standard mounting rail on the mounting surface. As1.
shown in figure below.
Fix the Standard Mounting RailFigure 2-1

Network Convert Camera·Quick Operation Guide
14
14
For cement surface mounting, you need to use the expansion
screw to fix the camera.
For wooden surface mounting, you can just use the
self-tapping screw to fix the camera.
Hang the hook which is on upper-side of the main unit onto the2.
rail, press a little harder on the lower part of the main unit, and
then the elastic clasp will be automatically buckled. As shown in
figure below.
Buckle the Main UnitFigure 2-2

Network Convert Camera·Quick Operation Guide
15
15
If you already had a standard rail installed, you can buckle the main
unit onto the installed rail directly. As shown in figure below.
Buckle the Main Unit onto Standard RailFigure 2-3
2.1 Installation of Block-Shaped Sensor Unit
This series of camera support concealed mounting and exposed
mounting with a decorative cover.
2.1.1 Concealed Mounting
Please make sure that the mounting surface is suitable for adhesive
pasting.
Steps:
Drill on the mounting surface. As shown in figure below.1.

Network Convert Camera·Quick Operation Guide
16
16
Drill on the SurfaceFigure 2-4
Make sure the drilling hole is big enough for the camera lens.
Remove a side of the adhesive tape on the bracket. Paste the2.
bracket on mounting surface by aligning with the drilled hole.
Paste the BracketFigure 2-5

Network Convert Camera·Quick Operation Guide
17
17
Install the block-shaped sensor unit into the bracket and make it3.
to be buckled.
Tighten the fastening screw on the top of the bracket.4.
Insert the Block-shaped Sensor UnitFigure 2-6
2.1.2 Exposed Mounting
Steps:
Fix the Block-shaped sensor unit on the mounting surface with1.
screws. As shown in figure below.

Network Convert Camera·Quick Operation Guide
18
18
Fix the Block-shaped Sensor UnitFigure 2-7
For cement surface mounting, you need to use the expansion
screw to fix the camera.
For wooden surface mounting, you can just use the
self-tapping screw to fix the camera.
Shield the sensor unit with the decorative cover. As shown in5.
figure below.

Network Convert Camera·Quick Operation Guide
19
19
Hood the CoverFigure 2-8
2.2 Installation of Cylindrical Sensor Unit
This series of camera only support concealed mounting.
Please make sure that the mounting surface is suitable for adhesive
pasting.
Steps:
Drill on the mounting surface. As shown in figure below.1.