HIK VISION DS-2CE71D0T-PIRL User manual

UM DS-2CE71D0T-PIRL 072718NA
TurboHD
Turret Camera
DS-2CE71D0T-PIRL
User Manual
Thank you for purcha ing our product. If there are any
que tion , or reque t , plea e contact the dealer.
Thi manual may contain technical incorrect place or
printing error , and the content i ubject to change
without notice. The update will be added to the new
ver ion of thi manual. We will readily improve or update
the product or procedure de cribed in the manual.
Regulatory In ormation FCC In ormation
Plea e take attention that change or modification not
expre ly approved by the party re pon ible for
compliance could void the u er’ authority to operate the
equipment.
FCC Compliance: Thi equipment ha been te ted and
found to comply with the limit for a Cla A digital device,
pur uant to part 15 of the FCC Rule . The e limit are
de igned to provide rea onable protection again t harmful
interference when the equipment i operated in a
commercial environment. Thi equipment generate , u e ,
and can radiate radio frequency energy and, if not
in talled and u ed in accordance with the in truction
manual, may cau e harmful interference to radio
communication . Operation of thi equipment in a
re idential area i likely to cau e harmful interference in
which ca e the u er will be required to correct the
interference at hi own expen e.
FCC Conditions
Thi device complie with part 15 of the FCC Rule .
Operation i ubject to the following two condition :
1. Thi device may not cau e harmful interference.
2. Thi device mu t accept any interference received,
including interference that may cau e unde ired
operation.
EU Con ormity Statement
Thi product and, if applicable, the upplied
acce orie too are marked with “CE” and comply
therefore with the applicable harmonized
European tandard li ted under the Low Voltage Directive
2014/35/EU, the EMC Directive 2014/30/EU, the RoHS
Directive 2011/65/EU.
2012/19/EU (WEEE Directive): Product marked with thi
ymbol cannot be di po ed of a un orted
municipal wa te in the European Union. For proper
recycling, return thi product to your local upplier
upon the purcha e of equivalent new equipment,
All manuals and user guides at all-guides.com
all-guides.com

UM DS-2CE71D0T-PIRL 072718NA
or di po e of it at de ignated collection point . For more
information ee: www.recyclethi .info.
2006/66/EC (Battery Directive): Thi product contain a
battery that cannot be di po ed of a un orted
municipal wa te in the European Union. See the
product documentation for pecific battery
information. The battery i marked with thi
ymbol, which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling,
return the battery to your upplier or to a de ignated
collection point. For more information ee:
www.recyclethi .info.
Industry Canada ICES-003 Compliance
Thi device meet the CAN ICES-3 (A)/NMB-3(A) tandard
requirement .
Warning
Thi i a cla A product. In a dome tic environment thi
product may cau e radio interference in which ca e the
u er may be required to take adequate mea ure .
Sa ety Instruction
The e in truction are intended to en ure that u er can
u e the product correctly to avoid danger or property lo .
The precaution mea ure i divided into “Warning ” and
“Caution .”
Warnings: Seriou injury or death may occur if any of the
warning are neglected.
Cautions: Injury or equipment damage may occur if any of
the caution are neglected.
Warnings
Follow
the e
afeguard to prevent
eriou injury or death.
Cautions
Follow the e
precaution to prevent
potential injury or material
damage.
Warnings
• In the u e of the device, you mu t be in trict compliance
with the electrical afety regulation of the nation and
region. 
• Input voltage hould meet both the SELV (Safety Extra
Low Voltage) and the Limited Power Source with 12 VDC
according to the IEC60950-1 tandard. Refer to technical
pecification for detailed information. 
• Do not connect multiple device to one power adapter to
avoid over-heating or a fire hazard cau ed by overload. 
• Make ure that the plug i firmly connected to the power
ocket. 
• Make ure that the device i firmly fixed if wall mounting
or ceiling mounting i adopted. 
• If moke, odor or noi e ri e from the device, turn off the
power at once and unplug the power cord, and then
contact the ervice center. 
• Never attempt to di a emble the camera by
unprofe ional per onal. 
Cautions
• Do not drop the camera or ubject it to phy ical hock. 
• Do not touch enor module with finger .
• Do not place the camera in extremely hot, cold (the
All manuals and user guides at all-guides.com

UM DS-2CE71D0T-PIRL 072718NA
operating temperature hall be -40° to 60° C), du ty or
damp location , and do not expo e it to high
electromagnetic radiation. 
• If cleaning i nece ary, u e a clean cloth with a bit of
ethanol, and wipe it gently.
• Do not aim the camera at the un or extra bright place .
• The en or may be burned out by a la er beam, o if any
la er equipment i in u e, make ure that the urface of
the en or i not expo ed to the la er beam.
• Do not expo e the device to high electromagnetic
radiation or extremely hot, cold, du ty, or damp
environment.
• To avoid heat accumulation, good ventilation i required
for the operating environment.
• Keep the camera away from liquid while in u e for non-
waterproof device. 
• While in delivery, the camera hall be packed in it
original packing or packing of the ame texture. 
Mark Description
Mark
Description
D
C Voltage
1Introduction
1.1 Product Features
The main feature are a follow :
• High performance CMOS en or 
• IR cut filter with auto witch 
• OSD menu with configurable parameter 
• Auto white balance 
• Internal ynchronization 
• SMART IR mode 
• Vi ible alarm 
• PIR detection 
• 3-axi adju tment 
1.2 Overview
Figure 1, Camera Overview
2Installation
Be ore you start:
• Make ure that the device in the package i in good
condition and all the a embly part are included. 
• Make ure that all the related equipment i powered off
during the in tallation. 
• Check the pecification of the product for the in tallation
environment. 
• Check that the power upply matche your required
All manuals and user guides at all-guides.com

UM DS-2CE71D0T-PIRL 072718NA
output to avoid damage. 
• Make ure the wall i trong enough to with tand three
time the weight of the camera, and the mount. 
• If the wall i concrete, in ert expan ion crew before
in talling the camera. If the wall i wood, u e elf-tapping
crew to ecure the camera. 
• If the product doe not function properly, contact your
dealer or the neare t ervice center. Do NOT di a emble
the camera for repair or maintenance your elf. 
2.1 Ceiling/Wall Mounting without Junction Box
1. Di a emble the camera.
1). Rotate the camera to align the notch to one of the
mark .
2). Pry the mounting ba e with a flat object (e.g., a
coin) to remove it from the camera body.
2. Pa te the drill template ( upplied) to where you want to
in tall the camera.
3. Drill the crew hole and the cable hole (optional) in the
ceiling/wall according to the drill template.
Figure 2, Drill Template
Note:
Drill the cable hole if u ing the ceiling outlet to route the
cable.
4. Attach the mounting ba e to the ceiling/wall, and
ecure them with upplied crew .
Figure 3, Attach Mounting Ba e to Ceiling
Note:
The upplied crew package contain elf-tapping crew
and expan ion bolt . 
For concrete wall/ceiling, expan ion bolt are required to
fix the camera. For wood wall/ceiling, elf-tapping crew
are required. 
5. Route the cable through the cable hole or ide
opening.
6. Align the camera with the mounting ba e, and ecure
the camera on the mounting ba e.
All manuals and user guides at all-guides.com

UM DS-2CE71D0T-PIRL 072718NA
Figure 4, Secure Camera to Mounting Ba e
7. Connect the corre ponding cable uch a power cord
and video cable.
8. Power on the camera to check if the image on the
monitor i at an optimum angle. If not, adju t the
camera according to the figure below to get an
optimum angle.
Figure 5, 3-Axi Adju tment
1). Hold the camera body and rotate the enclo ure to
adju t the pan po ition [0° to 360°].
2). Move the camera body up and down to adju t the
tilt po ition [0° to 75°].
3). Rotate the camera body to adju t the rotation
po ition [0° to 360°].
2.2 Mounting with Inclined Ceiling Mount
Be ore you start:
You need to purcha e an inclined ceiling mount
eparately.
1. Pa te the drill template ( upplied) where you want to
in tall the camera.
2. Drill crew hole and the cable hole on the ceiling/wall
according to the upplied drill template.
Figure 6, Drill Template
3. Di a emble the inclined ceiling mount with a
crewdriver.
4. In tall the turret camera’ mounting ba e on the
inclined ceiling mount’ cover with three PM4 crew .
All manuals and user guides at all-guides.com

UM DS-2CE71D0T-PIRL 072718NA
Figure 7, In tall Turret Camera’ Mounting Ba e
5. In tall the inclined ceiling mount’ body on the
ceiling/wall with four PA4 × 25 crew .
Figure 8, Fix the Inclined Ceiling Mount’ Body
6. Combine the inclined ceiling mount’ cover with it
body with upplied crew .
7. Repeat tep 5 to 8 of Ceiling/Wall Mounting without
Junction Box to complete the in tallation.
Figure 9, Fix Camera to the Inclined Ceiling Mount
2.3 Ceiling/Wall Mounting with Junction Box
Be ore you start:
You need to purcha e a junction box eparately.
1. Pa te the drill template on the ceiling/wall.
2. Drill crew hole and the cable hole (optional) in the
ceiling/wall according to the hole of the drill template.
Figure 10, Junction Box Drill Template
All manuals and user guides at all-guides.com
all-guides.com

UM DS-2CE71D0T-PIRL 072718NA
Note:
Drill a cable hole if u ing the ceiling outlet to route the
cable.
3. Take apart the junction box, and align the crew hole
of the turret camera’ mounting ba e with tho e on the
junction box’ cover.
Figure 11, In tall Turret Camera Mounting Ba e
4. Fix the mounting ba e on junction box’ cover with
upplied crew .
Figure 12, In tall Junction Box on Ceiling/Wall
5. Secure the junction box’ body with upplied crew on
the ceiling/wall.
6. Combine the junction box’ cover with the junction
box’ body.
Figure 13, Fix the Camera to the Junction Box
7. Repeat tep 5 to 8 of Ceiling/Wall Mounting without
Junction Box to in tall the camera to the junction box.
2.4 Wall Mounting
Be ore you start:
You need to purcha e a wall mount eparately.
1. Drill four crew hole in the wall according to the hole
on the mount.
2. In tall the mount to the wall by aligning the four crew
hole of the bracket with expan ion crew on the wall.
3. Secure the mount with four hex nut and wa her .
All manuals and user guides at all-guides.com

UM DS-2CE71D0T-PIRL 072718NA
Figure 14, In tall the Bracket
Figure 2-14 In tall Mounting Ba e to Bracket
4. In tall the mounting ba e of the turret camera to the
wall mount, and ecure them with upplied crew .
5. Route the cable through the mount.
6. Repeat tep 6 to 8 of Ceiling/Wall Mounting without
Junction Box to complete the in tallation.
3Menu Description
Purpose:
Call the menu by clicking the button on the PTZ Control
interface or call pre et no.95.
1. Connect the camera to the TVI DVR and the monitor.
Figure 15, Connection
2. Power on the analog camera, TVI DVR, and the monitor
to view the image on the monitor.
3. Click PTZ Control to enter the PTZ Control interface.
4. Call the camera menu by clicking the button or call
pre et no. 95.
All manuals and user guides at all-guides.com

UM DS-2CE71D0T-PIRL 072718NA
Figure 16, Main Menu Overview
5. Click the direction arrow to control the camera.
1). Click up/down direction button to elect the item.
2). Click Iris + to confirm the election.
3). Click le t/right direction button to adju t the value
of the elected item.
3.1 VIDEO FORMAT
You can elect the video format a 2 MP @ 25 fp or 2 MP
@ 30 fp .
3.2 LANGUAGE
Support Engli h and Chine e.
All manuals and user guides at all-guides.com

UM DS-2CE71D0T-PIRL 072718NA
3.3 EXPOSURE
EXPOSURE MODE
You can et the EXPOSURE MODE a GLOBAL, BLC, or
DWDR.
• GLOBAL


Normal expo ure mode, which adju t lighting
di tribution, variation , and non- tandard proce ing.
• BLC (Backlight Compensation)


Compen ate light to the object in the front to make it
clear, but may cau e overexpo ure of the background
where the light i trong.
• DWDR (Digital Wide Dynamic Range)


Help provide clear image even under backlight
circum tance . WDR balance the brightne level of
the whole image and provide clear image with detail .
AGC (Auto Gain Control)
Optimize image clarity in poor light condition . The level
can be et a HIGH, MEDIUM, or LOW. Select OFF to
di able the AGC function.
Note:
The noi e will be amplified when the AGC i on.
3.4 DAY/NIGHT
COLOR, B&W (Black White), and AUTO are electable for
DAY/NIGHT witche .
Note:
Under LIGHTING mode, the image i in color all the time,
and there i no DAY/NIGHT etting in the menu.
• COLOR
The image i colored in day mode all the time.
• B/W
The image i black and white all the time, and it i be t
to turn the IR LIGHT on in poor light condition .
• AUTO
You can turn on/off the IR LIGHT and et the SMART IR
value in thi menu.
Figure 17, DAY/NIGHT
˗IR LIGHT


You can turn on/off the infrared to meet the
requirement of different circum tance .
˗SMART IR


The Smart IR function i u ed to adju t the light to it
mo t uitable inten ity, and prevent the image from
over expo ure. The SMART IR value can be adju ted
from 0 to 3. The greater the value i , the more
obviou effect are.
All manuals and user guides at all-guides.com