HIK VISION UD.6L0201D0151A01 User guide

UD.6L0201D0151A01
Network Camera
Quick Operation Guide

Network Camera·Quick Operation Guide
1
1
Thank you for purchasing our product. If there are any questions,
or requests, please do not hesitate to contact the dealer.
About This Document:
This manual applies to DS-2CD8464F-E(I)(W),
DS-2CD8433F-E(I)(W) series cameras.
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without notice.
The updates will be added to the new version of this manual. We
will readily improve or update the products or procedures
described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested for fire, shock or casualty hazards
as outlined in UL’s Standard(s) for Safety, UL60950-1. UL
Certification does not cover the performance or reliability of the
security or signaling aspects of this product. UL MAKES NO
REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY
OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS
PRODUCT.
0400031020820

Network Camera·Quick Operation Guide
2
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized
European standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC.

Network Camera·Quick Operation Guide
3
3
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.

Network Camera·Quick Operation Guide
4
4
Contents
1 Appearance Description ................................................ 5
1.1 Camera Description ..............................................5
1.2 Camera Wiring Diagram ........................................9
2 Installation ................................................................. 10
3 Setting the Network Camera over the LAN .................. 16
4 Accessing via WEB browser......................................... 22

Network Camera·Quick Operation Guide
5
5
1Appearance Description
1.1 Camera Description
Figure 1-1 Overview
Table 1-1 Description
No.
Description
1
Photosensitive resistance
2
Infrared light
3
PIR sensor
4
Microphone
5
Lens
6
Alarm: Indicator is solid red when the camera is
armed and it is solid blue when the camera is
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Network Camera·Quick Operation Guide
6
6
No.
Description
unarmed.
7
Indicator flashes blue when movement or presence
is detected in its field of view.
8
Link: Indicator flashes orange when network
connection is functioning properly.
9
Tri-axial adjustment bracket
10
USB interface
11
Battery
12
Speaker
13
RESET: Reset button.
14
Micro SD card slot
15
Power supply interface
16
10M / 100M self-adaptive Ethernet interface & PoE
Note: To reset the default parameters to the camera, you need to
press and hold the RESET button and power on the camera. After
the power on of the camera, you must still press and hold the Reset
button for about 20 seconds.

Network Camera·Quick Operation Guide
7
7
Remote Control:
Figure 1-2 Remote Control
Table 1-2 Remote Control Button Description
Button
Name
Description
Status
Indicator
Indicating the status of the remote; when you press the
button on the remote, the indicator flicks in red.
Arm Button
Press the button to arm the camera. In arming status, the
alarm function, such as the wireless alarm and the PIR alarm
is enabled.

Network Camera·Quick Operation Guide
8
8
Button
Name
Description
Disarm
Button
Press the button to disarm the camera. In the disarming
status, the alarm linkage is disabled.
Emergency
Button
Press the button to trigger the emergency alarm. The
emergency alarm has the highest priority.
Stream
Sending
Switch
Switch for the video stream transmitting. Press the button to
stop or start video stream sending. When the video stream is
stopped, you can’t see the live view or get the record stream
on the remote client or browser.

Network Camera·Quick Operation Guide
9
9
1.2 Camera Wiring Diagram
Figure 1-3 Wiring Diagram

Network Camera·Quick Operation Guide
10
10
2Installation
Notes:
Read the following contents carefully before the installation.
Make sure that all the related equipment is power-off during
the installation.
Check whether the power supply is matched with your AC
outlet to avoid damage.
Do not place the camera in extremely hot or damp
environment. To avoid heat accumulation, good ventilation is
required for a proper operating environment.
If the product does not function properly, please contact your
dealer or the nearest service center. Do not disassemble the
camera for repair or maintenance by yourself.
The cube camera can be installed to wall, ceiling or table. Ceiling
mounting is taken as an example in this section; if you adopt wall
mounting or table mounting, you can also take below procedure as
a reference.
Steps:
1. Slide the right cover to remove it from the camera. Remove the
fixator.

Network Camera·Quick Operation Guide
11
11
Figure 2-1 Remove the Cover and Fixator
2. Remove the battery cover; insert the battery; reinstall the
battery cover.
Note: If you want to install the battery, then you can take this
step.
Fixator
Right cover

Network Camera·Quick Operation Guide
12
12
Figure 2-2 Install the Battery
3. Stick the drilling template to the ceiling.
Note:
For cement ceiling mounting, you need to use the
expansion screw to fix the camera. The mounting hole of
the expansion pipe on the wall should align with the
mounting hole of the drilling template.
For wooden ceiling mounting, you can just use the
self-tapping screw to fix the camera.
The ceiling must be strong enough to withstand more than
3 times the weight of the camera.
Battery
Battery cover

Network Camera·Quick Operation Guide
13
13
Figure 2-3 Stick the Drilling Template
4. Use two PA4X24 screws to fix the camera to the ceiling and the
screw hole on the camera should align with the mounting hole
on the drilling template.
Figure 2-4 Fix the Camera
Cable outlet
Drilling template

Network Camera·Quick Operation Guide
14
14
5. Connect the network cable and power cable; reinstall the right
cover and fixator.
Note: If you need to pull the cable through the side cable
outlet of the camera, pull the cables from the slot without
reinstall the fixator.
Figure 2-5 Reinstall the cover and Fixator
6. Adjust image
1). View the image of the camera over the network.
2). Loosen the packing nut 1 to adjust the panning position
and tilting position.
3). Fasten the packing nut 1.
4). Loosen the packing nut 2 to rotate the camera.
5). Fasten the packing nut 2.
Slot

Network Camera·Quick Operation Guide
15
15
Figure 2-6 Adjust the Camera
Packing nut 1
Pan
Tilt
Packing nut 2

Network Camera·Quick Operation Guide
16
16
3Setting the Network
Camera over the LAN
Purpose:
To view and configure the camera via LAN (Local Area Network),
you need to connect the network camera in the same subnet with
your PC. Then, install the SADP or iVMS-4200 software to search
and change the IP of network camera.
The following figure shows the cable connection of network
camera and PC:
Figure 3-1 Wiring over LAN
Set the IP address of the camera for accessing via LAN.
Steps:
1. To get the IP address, you can choose either of the following
methods:
Use SADP, a software tool which can automatically detect
network camera in the LAN and list the device information like
IP address, subnet mask, port number, device serial number,
device version, etc., shown in Figure 3-2.

Network Camera·Quick Operation Guide
17
17
Use iVMS-4200 software and to list the online devices. Please
refer to the user manual of client software for detailed
information.
2. Change the IP address and subnet mask to the same subnet as
of your PC.
Refer to the following introductions to set IP address with
SADP software:
Search active devices online
Search online devices automatically:
After launch the SADP software, it automatically searches
the online devices every 15 seconds from the subnet where
your computer locates. It displays the total number and
information of the searched devices in the Online Devices
interface. Device information including the device type, IP
address, port number, gateway, etc. will be displayed.

Network Camera·Quick Operation Guide
18
18
Figure 3-2 Searching Online Devices
Note: Device can be searched and displayed in the list in 15
seconds after it goes online; it will be removed from the list
in 45 seconds after it goes offline.
Search online devices manually:
You can also click to refresh the online
device list manually. The newly searched devices will be
added to the list.

Network Camera·Quick Operation Guide
19
19
Note: You can click or on each column heading
to order the information; you can click to show the
device table and hide the network parameter panel on the
right side, or click to show the network parameter
panel.
Modify device information
Steps:
1). Select the device to be modified in the device list as shown
in Figure 3-3. The network parameters of the device will be
displayed in the Modify Network Parameters panel on the
right side as shown in Figure 3-4.
2). Edit the modifiable network parameters, e.g. IP address
and port number.
3). Enter the password of the admin account of the device in
the Password field and click to save the
changes.