HIK VISION 23 Series User manual

0
Network Turret Camera
Quick Start Guide
UD04378B
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

1
Network Turret Camera·Quick Start Guide
Quick Start Guide
COPYRIGHT © 2017 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures,
graphs are the properties of Hangzhou Hikvision Digital Technology
Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
This user manual (hereinafter referred to be “the Manual”) cannot
be reproduced, changed, translated, or distributed, partially or
wholly, by any means, without the prior written permission of
Hikvision. Unless otherwise stipulated, Hikvision does not make any
warranties, guarantees or representations, express or implied,
regarding to the Manual.
About this Manual
This Manual is applicable to 23xx Network Camera.
The Manual includes instructions for using and managing the
product. Pictures, charts, images and all other information
hereinafter are for description and explanation only. The
information contained in the Manual is subject to change, without
notice, due to firmware updates or other reasons. Please find the
latest version in the company website
(http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the
properties of Hikvision in various jurisdictions. Other trademarks and
logos mentioned below are the properties of their respective
owners.
1
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

2
Network Turret Camera·Quick Start Guide
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE
PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND
FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,
AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION, MERCHANTABILITY,
SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND
NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE
LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR
LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF
DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF
THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF
PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL
NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION,
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER
ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL
RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS
PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE
APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT
THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
2
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

3
Network Turret Camera·Quick Start Guide
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE
APPLICABLE LAW, THE LATER PREVAILS.
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Conditions
3
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

4
Network Turret Camera·Quick Start Guide
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the EMC Directive 2014/30/EU, the RoHS
Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more information
see:www.recyclethis.info
4
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

5
Network Turret Camera·Quick Start Guide
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards
requirements.
Safety Instruction
These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings
are neglected.
Cautions: Injury or equipment damage may occur if any of the
cautions are neglected.
Warnings Follow these
Cautions Follow these
safeguards to prevent serious
precautions to prevent potential
injury or death.
injury or material damage.
Warnings
● Proper configuration of all passwords and other security
settings is the responsibility of the installer and/or end-user.
● In the use of the product, you must be in strict compliance with
the electrical safety regulations of the nation and region. Please
refer to technical specifications for detailed information.
5
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

6
Network Turret Camera·Quick Start Guide
● Input voltage should meet both the SELV (Safety Extra Low
Voltage) and the Limited Power Source with 12 VDC according
to the IEC60950-1 standard. Please refer to technical
specifications for detailed information.
● Do not connect several devices to one power adapter as
adapter overload may cause over-heating or a fire hazard.
● Please make sure that the plug is firmly connected to the power
socket. When the product is mounted on wall or ceiling, the
device shall be firmly fixed.
● If smoke, odor or noise rise from the device, turn off the power
at once and unplug the power cable, and then please contact
the service center.
Cautions
● Make sure the power supply voltage is correct before using the
camera.
● Do not drop the camera or subject it to physical shock.
● Do not touch sensor modules with fingers. If cleaning is
necessary, use clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period,
please replace the lens cap to protect the sensor from dirt.
● Do not aim the camera at the sun or extra bright places.
Blooming or smearing may occur otherwise (which is not a
malfunction), and affect the endurance of sensor at the same
time.
6
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

7
Network Turret Camera·Quick Start Guide
● The sensor may be burned out by a laser beam, so when any
laser equipment is in using, make sure that the surface of
sensor will not be exposed to the laser beam.
● Do not place the camera in extremely hot, cold (the operating
temperature shall be-30°C ~+60°C , or -40°C ~ +60°C if the
camera model has an “H” in its suffix), dusty or damp locations,
and do not expose it to high electromagnetic radiation.
● To avoid heat accumulation, good ventilation is required for
operating environment.
● Keep the camera away from liquid while in use.
● While in delivery, the camera shall be packed in its original
packing, or packing of the same texture.
● Regular part replacement: a few parts (e.g. electrolytic
capacitor) of the equipment shall be replaced regularly
according to their average enduring time. The average time
varies because of differences between operating environment
and using history, so regular checking is recommended for all
the users. Please contact with your dealer for more details.
● Improper use or replacement of the battery may result in
hazard of explosion. Replace with the same or equivalent type
only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.
● If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance.) 0504051070109
7
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

8
Network Turret Camera·Quick Start Guide
Table of Contents
1 Appearance Description ............................................................... 10
1.1 Type I ............................................................................ 10
1.2 Type II ........................................................................... 11
1.3 Type III .......................................................................... 12
1.4 Type IV .......................................................................... 13
2 Installation.................................................................................... 15
2.1 Ceiling Mounting........................................................... 15
2.1.1 Type I.................................................................. 15
2.1.2 Type II................................................................. 20
2.1.3 Type III................................................................ 24
2.1.4 Type IV ............................................................... 27
2.2 Mounting with Brackets ................................................ 31
2.2.1 Wall Mounting.................................................... 32
2.2.2 Pendant Mounting ............................................. 34
2.3 Network Cable Water-proof Accessory Installation ....... 36
3 Setting the Network Camera over the LAN .................................. 39
3.1 Wiring ........................................................................... 39
3.2 Activating the Camera................................................... 40
3.2.1 Activation via Web Browser................................ 40
3.2.2 Activation via SADP Software ............................. 41
3.3 Modifying the IP Address .............................................. 43
4 Accessing via Web Browser .......................................................... 46
5 Operating via Hik-Connect App .................................................... 48
5.1 Enable Hik-Connect Service on Camera......................... 48
5.1.1 Enable Hik-Connect Service via SADP Software .. 48
5.1.2 Enable Hik-Connect Service via Web Browser .... 49
8
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

9
Network Turret Camera·Quick Start Guide
5.2 Hik-Connect Setup ........................................................ 51
5.3 Adding Camera to Hik-Connect ..................................... 51
5.4 Initializing the Memory Card ......................................... 53
9
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

10
5
6
4
1
2
3
Network Turret Camera·Quick Start Guide
1 Appearance Description
This camera series of turret camera has four appearance types.
1.1 Type I
Figure 1-1 Overview of Type I Turret Camera
Table 1-1 Description
No.
Description
No.
Description
1
Trim Ring
4
Camera
2
Enclosure
5
Power Cord
3
Mounting Base
6
10M/100M self-adaptive
Ethernet interface
10
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

11
1
2
3
6
5
4
Network Turret Camera·Quick Start Guide
1.2 Type II
Figure 1-2 Overview of Type II Turret Camera
Table 1-2 Description
No.
Description
No.
Description
1
Trim Ring
4
Camera
2
Enclosure
5
Power Cord
3
Mounting Base
6
10M/100M self-adaptive
Ethernet interface
11
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

12
1
2
3
6
5
78
4
9
10 11
Network Turret Camera·Quick Start Guide
1.3 Type III
Overview of Type III Turret Camera
Table 1-3 Description
No.
Description
No.
Description
1
Trim Ring
7
Audio Output
2
Enclosure
8
1-ch Alarm Input and
1-ch Alarm Output
3
Mounting Base
9
RST (Reset) Button
12
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

13
1
2
3
45
6
10
9
10 9
Network Turret Camera·Quick Start Guide
No.
Description
No.
Description
4
Camera
10
Memory Card Slot
5
Power Cord
11
MIC
6
10M/100M self-adaptive
Ethernet interface
Note:
Press Reset button about 10s when the camera is power on or
rebooting to restore the default settings, including the user name,
password, IP address, port No., etc.
1.4 Type IV
Figure 1-3 Type IV Turret Camera
13
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

14
Network Turret Camera·Quick Start Guide
Table 1-4 Description
No.
Description
No.
Description
1
Trim Ring
5
Power Cord
2
Enclosure
6
10M/100M self-adaptive
Ethernet interface (PoE)
3
Mounting Base
7
RST (Reset) Button
4
Camera
8
Memory Card Slot
Notes:
● For this type IV camera, the layout of memory card slot and
reset button may be different from model to model.
● Press Reset button about 10s when the camera is power on or
rebooting to restore the default settings, including the user
name, password, IP address, port No., etc.
14
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

15
Network Turret Camera·Quick Start Guide
2 Installation
Before you start:
● Make sure the device in the package is in good condition and all
the assembly parts are included.
● The standard power supply is 12 VDC, please make sure your
power supply matches with your camera.
● Make sure all the related equipment is power-off during the
installation.
● Check the specification of the products for the installation
environment.
● Make sure that the wall is strong enough to withstand four
times the weight of the camera and the bracket.
For the camera that supports IR, you are required to pay attention to
the following precautions to prevent IR reflection:
● Make sure that there is no reflective surface too close to the
camera lens. The IR light from the camera may reflect back into
the lens causing reflection.
2.1 Ceiling Mounting
2.1.1 Type I
Steps:
1. Disassemble the camera.
1). Loosen the lock screw on the mounting base and take it off
from the camera.
15
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

16
Trim Ring
Camera
Lock Screw
②
③
①
Mounting Base
Network Turret Camera·Quick Start Guide
2). Rotate the trim ring anticlockwise to take it off from the
camera.
3). Separate the camera and the enclosure.
2.
to the drill template.
Disassemble the CameraFigure 2-1
Drill the screw holes and the cable hole on the ceiling according
Figure 2-2 The Drill Template
16
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

17
Network Turret Camera·Quick Start Guide
There are two cable outlet methods. One is to route the cables
through the cable hole, and the other is to route the cables through
the side outlet shown below.
Figure 2-3 Side Outlet
Three side outlets on the enclosure are selectable, which makes
routing the cables easier instead of drilling a cable hole on the ceiling.
Use a plier to remove the plastic and route the cables through the
hole.
3. Fix the mounting base to the ceiling with the supplied
expansion screws.
17
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

18
Ceiling
Network Turret Camera·Quick Start Guide
Figure 2-4 Secure the Mounting to the Ceiling
4. Connect the corresponding power/network cable and then
install the camera to the mounting base with the supplied
screws. Rotate the camera to secure it.
Figure 2-5 Secure the Camera to the Mounting Base
5. Adjust the Lens.
1). Loosen the lock screw.
18
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

19
Lock Screw
P Direction
360o
R Direction
360o
T Direction
0o ~75o
Network Turret Camera·Quick Start Guide
Figure 2-6 Loosen Lock Screw
2). Rotate the enclosure to adjust the pan angle; rotate the
camera to adjust the tilt angle.
Figure 2-7 Adjust the Lens
3). Tighten the lock screw to fix the optimum surveillance
angle.
6. Attach the trim ring to the camera and rotate the trim ring
clockwise to get it secured.
19
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]