Hillsdale Furniture 1579-500 User manual

STEP 1
Begin assembly by attaching each Leg Extension (K) into the bottom of each post on the Headboard
Panel (J) by tapping in place with a r bber mallet if needed. Once in place, sec re each Leg Extension
(K) from the back with 2 Allen Bolts (B) & 2 Flat Washers (D) as shown in Fig re 1.
STEP 2
Attach each Side Rail (M) to the front of each Leg Extension (K) by aligning holes and sec ring with
2 Allen Bolts (A), 2 Spring Washers (C) & 2 Flat Washers (D) per each side. Tighten all bolts sing
the Allen Wrench (G) that has been provided.
STEP 3
Also attach each Side Rail (M) to the inside of each post on the Footboard Panel (L) by aligning holes
and sec ring with 2 Allen Bolts (A), 2 Spring Washers (C) & 2 Flat Washers (D) per each side. Tighten
all bolts. See next page for Steps 4 & 5.
08/18/10
Page 1 of 2
MANDALAY BED SET
Model #1579-500 Queen Bed Set
Model #1579-550 Queen Rails
Examine all packaging material for small parts that may have come loose d ring shipment. Periodic checks are recommended to ins re that all
components are in proper position, tight and free from damage. Keep this assembly instr ction for f t re reference. Ad lt assembly is req ired.
C stomer Service Phone N mber: 502-562-0000
FURNITURE, LLC.
HILLSDALE
HARDWARE LIST
(14) Allen Bolts 1/4 x 1
(4) Allen Bolts 1/4 x 3/4
(8) Spring Washers 1/4
(12) Flat Washers 1/4 x 5/8
(6) Hex N ts 1/4
(1) Hex Wrench 1/4
(1) Allen Wrench 1/4
A
B
C
D
E
F
G
PARTS LIST
(1) Headboard Panel
(2) Leg Extensions
(1) Footboard Panel
(2) Side Rails
(2) Do ble Leg S pport Rails
(1) Single Leg S pport Rail
J
K
L
M
N
P
ABCDE
FG
BD
BD
View from backside J
K
LM
K
M
K
J
A
C
D
D
C
A
A
C
D
D
C
A
A
C
D
D
C
A
A
C
D
D
C
A
FIGURE 1

E
E
E
E
08/18/10
Page 1 of 2
CARE & MAINTENANCE : The to ch of a soft cloth is all the maintenance the finish will ever need. Please do not se harsh or abrasive cleaners for polishing,
as they may ca se damage to the finish. Periodic checks are recommended to make s re that all bolts, screws and n ts are sec rely tightened.
N
J
M
M
L
N
P
A
A
A
A
A
E
E
STEP 4
Attach each Do ble Leg S pport Rail (N) to the inside of each Side Rail (M) at the head and foot
sing 1 Allen Bolt (A) & 1 Hex N t (E) per each end. Note: The Double Leg Suppo ts should be
positioned at the heade and foote of the bed. Tighen each n t sing the Hex Wrench (F) that has
been provided.
STEP 5
Attach the Single Leg S pport Rail (P) to the inside of each Side Rail (M) in the center sing 1 Allen
Bolt (A) & 1 Hex N t (E) per each end. Note: The Single Leg Suppo t should be positioned at the
cente of the bed. Tighten all n ts.
The assembly is now complete.
A