Hinkley 51000 BZ User manual

HINKLEY LIGHTING 12600 Berea Road Cleveland, OH 44111 800.446.5539 / 216.671.3300 www.hinkleylighting.com
installation instructions
Family: 120V Series Small Well Light Item No. 51000 BZ
1. Find a clear area in which you can work.
2. Carefully review instructions prior to assembly.
3. Gather tools required: WIRE STRIPPERS, PHILIPS HEAD SCREWDRIVER,
SILICONE GREASE, THREAD SEALANT.
• Save these instructions for future reference.
start here
51000
WARNING: LUMINAIRE MUST BE INSTALLED AND GROUNDED IN ACCORDANCE
WITH THE NATIONAL ELECTRICAL CODE (NEC) AND LOCAL CODES. FOR PORTABLE
STAKE OR SUFACE MOUNT USING A CORD AND PLUG, THE LUMINAIRE MUST BE
PLUGGED INTO A RECEPTACLE PROTECTED BY A GROUND FAULT CIRCUIT
INTERRUPTER (GFI). FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY
AND/ OR DAMAGE TO THE LUMINAIRE.
ALWAYS USE UL RECOGNIZED WIRE CONNECTORS FOR CONNECTIONS.
IN GROUND LUMINAIRE IS ETL LISTED FOR BELOW GRADE INSTALLATION ONLY.
SAFETY WARNING: LUMINAIRE CAN BECOME VERY HOT DEPENDING ON THE
LAMP WATTAGE USED. LENS AND HOUSING AROUND THE LAMP CAN BECOME
HOT ENOUGH TO BLISTER HANDS. PARTICULAR CARE SHOULD BE TAKEN NOT TO
LOCATE LUMINAIRES WHERE SMALL CHILDREN CAN REACH THEM IF HIGH
WATTAGE LAMPS ARE USED.
MAINTENANCE NOTE: TO ASSURE PROPER OPERATION AND EFFICIENCY AND TO
PREVENT LUMINAIRE OVERHEATING, LENS MUST BE KEPT CLEAN AND FREE OF
DIRT, LEAVES, TRASH, AND MINERAL DEPOSITS FROM WATER. A REGULAR
SCHEDULE MAINTENANCE PROGRAM IS RECOMMENDED.
1. Please refer to the mounting instructions located on the back of this sheet to
continue installation of this fixture.
lamp installation replacement
1. To prevent electrical shock, disconnect from the electrical supply before servicing.
2. Loosen the cover screws (B) and remove cover (C).
3. Remove lens with gasket assembly (D) to expose lamp.
4. Replace lamp with correct wattage and type marked on fixture label.
CAUTION: DO NOT EXCEED MAXIMUM WATTAGE MARKED ON LUMINAIRE LABEL.
5. Clean the gasket (D) and gasket channel.
6. Re-install gasketed lens and cover (C), follow by tightening the screws (B) evenly.
Info 51000 BZ: Lamp Type is R20, R30, R40, PAR20, PAR30, PAR 38, Incandescent
Maximum Wattage is 100 watts per bulb.
Drawing 1 - Lamp Installation
B
C
D
3.4.08

mounting instructions
Family: 120V Series Small Well Light Item No. 51000 BZ
Drawing 2 - Fixture Mounting In Ground Installation
1. Make sure electrical supply is off at the circuit breaker before starting luminaire
installation or servicing.
2. If you are using an HID self reflector lamp in the luminaire an integrated ballast must
be used. Ask your local Hinkley Lighting representative or visit www.hinkleylighting.com
for information.
3. Dig hole approximately 16” deep by 15” in diameter - see Drawing 2.
4. Install conduit through the four 3/4” NPT holes (A) provided with this luminaire,
using Teflon tape or other thread sealant.
5. Using plug provided, seal unused conduit entry if required.
• Housing rim must be flush to 1/8” above finish grade to prevent water from
accumulating on lens.
• For a more secure intallation, rebar bracing (1) is recommended. Drill a hole for a 1/4”
bolt and nut in two of the stiffeners (2) located on the side of the luminaire. Attach
perforated strap (plumber’s tape) not provided to the drilled holes with 1/4” nuts and
bolts not provided.
• UL listed flexible conduit (3) is recommended for in and out connections to ease
fixture position and adjustment during installation.
6. Backfill after installation with pea gravel or sand (4).
Note: DO NOT fill with bark or other flammable material.
7. Pull supply wire (line in), through conduit into luminaire wire compartment.
8. Connect green ground wire from luminaire and green ground wire from the box to
green supply wire.
9. Wire luminaire as required using silicone filled safety connectors provided.
10. Please refer back to the front of this sheet to install lamp and complete installation
of this fixture.
Concrete Pour Installation
1. Fit concrete - guard plugs not provided over eight bosses with threaded inserts
beneath the flange in order to prevent poured concrete from back filling threaded
holes and hindering a secure tight seal of the lens cover.
Note: Failure to install concrete - guard plugs over bosses with threaded inserts will
void product warranty.
2. Follow instructions 1 and 2 of in ground installation instructions above.
3. Support luminaire in selected position using standard masonary procedures.
Note: UL listed flexible conduit is recommended for in and out connections to
ease fixture position and adjustment during installation.
• When installing in concrete housing rim must be flush to 1/8” above grade to
promote water runoff.
4. Pull supply wires (line in), through conduit into luminaire wire compartment.
5. Connect green ground wire from luminaire and green ground wire from box to
green supply wire.
6. Wire luminaire as required using silicone filled connectors.
7. Pour concrete at least 2” thick.
8. Please refer to the front of this sheet to install lamp and complete installation of this
fixture.
2
3
1. Determine which of the two mounting options are required and refer to the proper
set of instructions below.
1
A3
1
4
2
WARNING: TO REDUCE THE
RISK OF FIRE, OR INJURY
TO PERSONS:
1. Turn off/unplug and allow
to cool before replacing lamp.
2. Lamps get hot quickly!
Contact only switch/plug
when turning on.
3. Do not touch hot lens,
guard or enclosure.
4. Keep lamp away from
material that may burn.
5. Do not operate luminaire
fitting with a missing
or damaged cover.