Hisense HR6AF351B Mounting instructions

MODEL:HR6AF351B(S)

1

Operating Instructions
Dear customer,
To enable you to use your new FRIDGE effectively and safely, please read this instruction book
carefully before you use the appliance, which contains important information for installation, safe
use and maintenance of this appliance. Please keep the book for future reference and remember
to pass it on to the new owner. The following symbols will be found in the book to guide you
through the instructions:
Guide to use the instruction book
Warnings
Tips and notes
Operating instructions
Warnings are stressed with a warning triangle or with signal words (Warning!, Important!), which
are provided in the interest of your safety. Ensure that you understand them all before installing
and using this appliance.
Tips and notes will inform you with necessary knowledge of how to use the appliance econom-
ically and environmentally.
Operating instructions presented in the section of “Trouble shooting” contain instructions for
correction of possible malfunctions by users.
2

3
Disposal of the appliance
4
7
8
9
10
11
13
14
16

Caution:risk of fire
The refrigerant isobutene (R600a) is contained within the refrigerant circuit of the appliance, a
natural gas with a high level of environmental compatibility, which is nevertheless flammable.
During transportation and installation of the appliance,ensure that none of the components of
the refrigerant circuit becomes damaged.
The refrigerant (R600a) is flammable.
If the refrigerant circuit should become damaged:
Avoid open flames and sources of ignition.
Thoroughly ventilate the room in which the appliance is situated.
Tips : If any food scraps or oily substances are on the liner walls,
Please clean it immediately to avoid any damage.
4

Interior accessories
IMPORTANT! – in order to make the most of the volume of the fresh food storage compartment ,
the user can removed one ormore shelves, drawers, out of the appliance, according to your daily
use.
Defrosting in fresh food storage compartment
It is automatically controlled by switching the temperature regulator on or off so that there is no
need of operation of defrosting. Water from defrosting will be drained into an drip tray through a
drain pipe at the back of the fridge automatically.
Storage shelves/wire tray
Various glass or plastic storage shelves or wire trays are included with your appliance different
models have different combinations .
You should always slide one of the full size glass storage shelves into the lowest set of guides,
above the fruit and vegetable containers, and keep it in this position.
The height of the storage shelves can be adjusted:
To do this, pull the storage shelf forward until it can be swiveled upwards or downwards and
removed.
Please do the same in reverse to insert the shelf at a different height.
Warning!
Switching off the appliance.
6

6.Crisper drawer
7.Egg rack(inside) 8 Door rack cover 9.Door rack 10.Door lower rack
4
6
7
9
10
1
2
3
4
5
6
8
7
9
10
8

10

Changing The Light Bulb
Before changing the light bulb, either the refrigerator or disconnect the electricity leading into
the refrigerator at the main power supply. Failure to do so could result in electrical shock or
personal injury.
a) Remove the light cover out by one hand while
pressing the middle of the light cover by force with
the other hand.
b) Replace with a
light bulb that is of the same shape and size.
c) Replace the light bulb cover.
10 watt（or less than 10 watt）
Warning!
If the LED light bulb is damaged, DO NOT CHANG IT BY THE USER!
Changing the light bulb carry out by inexperienced persons may cause injury or serious
malfunctioning.it must be replaced by a qualified persons in order to avoid a hazard. Contact
your local Service Force Center for help.
Before changing the light bulb, switch off the appliance and unplug it, or pull the fuse or the
circuit breaker.light bulb data: 220-240 V,To switch off the appliance. Unplug the mains plug.
Press the bulb in the center with finger.
Ensure the foods placed in the refrigerator are dated and labeled, and used them in date order,
so you can consume them an its best.
11

1.Do not place warm foods into the appliance. Allow warm foods to cool first. Do not install the
appliance near cookers, radiators or other sources of warmth. High ambient temperatures cause
longer, more frequent operation of the compressor
2.In order to make the cooling system work efficiently, please make sure the side plates and back
plate of the product are with some distance from the wall. It is strongly recommended that its back
is 75mm away from the wall, its sides at least have a space of 100mm separately and the
height from over its top is not less than 100mm.
3.When the product works, please do not open the door too often or leave the door open any
longer than necessary.
4.Do not set temperature any colder than necessary.
6.The sketch map shows the right combination of the drawers, crisper and shelves which can
lead to the more energy efficiency.If users adjust the combination,it would result in the energy
consuming.
7.Store food logically. Do not exceed the storage period specified.
5.The direct cooling refrigerator needs to be defrosted when necessary. This will improve the cold
transfer and reduce energy consumption.
12

FRIDGE
FRIDGE
FRIDGE
FRIDGE

14
Correct Positioning
Good ventilation
For the purpose of safety, reliance, low power consumption
and durability to your fridge, a space should be left around
the . please keep 75mm of space between the
back of the appliance and the wall.
fridge
Power supply
The is only suitable to a single–phase alternating
current of 220-240V, (50±1) Hz.
freezer
Power Cord
The cord should be neither lengthened nor folded into a coil
during operation. Moreover, it is imperative not to keep the
power cord close to, or touching the compressor at the back
of the , as the surface temperature is quite warm while
operating, and touching may melt the insulation and cause
electrical leakage.
fridge
Protection from Moisture
Avoid placing the in a place where heavy moisture is
present, to minimize the possibility of rusting any metal parts.
It is imperative that the not be directly sprayed with
water, as it will cause poor insulation and current leakage
may occur.
fridge
fridge
±10%
220V

15
Level Surface
The surface on which is to be placed, must be flat and
solid. It should not be laid on any soft material such as foam
plastic, etc. if the is not on level, adjust the casters.
fridge
fridge
Protection from Heat
The should be far away from any heat source or direct fridge
sunshine.
Keep Away from Danger
It is not advisable for the to be placed near any
combustibles such as gas, petrol, alcohol, lacquer, banana
oil, etc. The above-mentioned objects can not be stored in
the .
fridge
fridge
Moving
When moving the , do not lie it horizontally
or lower it at an angle less than 45°.
fridge 45°

Congratulations on your purchase, This Document sets out terms
and conditions of your product warranty. Please Keep it with your
proof of purchase information in a safe place for future reference
should you require service to your product.
NAME OF PURCHASER _______________________________________________
ADDRESS __________________________________________________________
___________________________________________________________
CITY ______________________________ STATE _______ POSTCODE ________
PHONE (_____)_____________________
MOBILE (_____)_____________________
FAX (_____)_____________________
The Undersigned hereby acknowledges receipt of the Hisense
warranty service provided. I have read and understand the
conditions and terms of the warranty in its entirety.
SERIAL NUMBER
____________________________________________________________
STORE PURCHASED FROM
____________________________________________________________
CITY _______________________ STATE _______ POSTCODE ________
INVOICE NO. _______________________________________
MODEL NO. _______________________________________
DATE OF PURCHASE _________/___________/__________
SIGNATURE _________________________________________________
WARRANTY REGISTRATION
In order to register your warranty, please fill out and return with a copy of your invoice to:
Hisense Warranty Registration
PO BOX 360 Ferntree Gully VIC 3156 Australia
WARRANTY CLAIMS PROCEDURE
Please retain this portion for your records
36 MONTHS IN HOME REPAIR WARRANTY
Hisense Australia will provide its nearest service centre for repairs under warranty. You will need to
ensure that you have already called Hisense Warranty Centre and received a JOB NUMBER.
Before making a claim, please make sure that you understand the terms and conditions of the warranty
• Check and ensure the installation of all power cables to the power point are secure and power is turned on,
all cables leads and connectors are connected properly and that all switches are turned on and functioning
• Check that there is power at the power point by using a small appliance
• Check that all settings are set according to the instruction manual
• Please keep this certificate in a safe place together with your product receipt. Should you need to make a
claim, the responsibility of proof of ownership of the equipment is on you. If a claim is made that is found
not to be covered under this warranty, or no faulty hardware components are found, you will be charged at
Hisense or Hisense Authorised Service Center's standard service charge plus an administration fee.
PLEASE REFER TO THE TROUBLESHOOTING GUIDE
AT THE END OF THIS MANUAL
Service Procedure
Please have your original invoice, model, and serial number ready. To receive service, you are required to:
• Call 1800 447 367 . Service claims may be made between 9:00am and 5:00pm AEST week-
days excluding public holidays where a call representative will log your claim for processing.
• You will be provided a JOB NUMBER
• Normally under 24 hours of logging and receiving your proof of purchase for your claim, an Authorised
Service Agent will contact you to proceed with claim.