Hisun R-110V-500-165 6K User manual

Line Voltage Strip Light (Single Color)
R-110V-500-165 6K
R-110V-500-165 3K
ETL listed, 110VAC line voltage LED strip light.
IP67 rated, good for both indoor and outdoor use.
Various accessories available for all purposes.
Product Specification
Technical Data
Item Name:
110V-Cord-625-205 (Power)
Rated Input Voltage:
125 VAC
Rated Input Current:
≤ 5A
Output Wattage:
*625 Watt
Max Length:
165 Ft (50m)
Remote Control:
NO
Pin Type:
2-pin
Item Name:
R-110V-500-165
Color Option:
White / Warm White
Total Length per Roll:
165 Ft (50m)
Total Section per Roll:
100 pcs
Section Length:
20-inch (0.5m)
Roll Wattage:
500 W
Section Wattage:
5 W
Efficiency:
100 Lm/Watt
LED Type:
5730 SMD
LED Qt. per Roll:
3000 pcs
IP Rating:
IP67
Pin Type:
2-pin
* Please do not carry load that exceeds specified output wattage to avoid over-load burn out.

Line Voltage Strip Light (RGB)
R-110V-450-165 RGB
ETL listed, 110VAC line voltage LED strip light.
IP67 rated, good for both indoor and outdoor use.
Various accessories available for all purposes.
Product Specification
Technical Data
Item Name:
110V-C300-99 (Power & Controller)
Rated Input Voltage:
125 VAC
Rated Input Current:
≤ 5A
Output Wattage:
*300 Watt
Max Length:
99 Ft (30m)
Remote Control:
YES
Control Distance:
16 Ft (5m)
Control Type:
IR
Pin Type:
4-pin
Item Name:
R-110V-450-165 RGB
Color Option:
RGB
Total Length per Roll:
165 Ft (50m)
Total Section per Roll:
100 pcs
Section Length:
40-inch (1m)
Roll Wattage:
450 W
Section Wattage:
4.5 W
Efficiency:
100 Lm/Watt (max)
LED Type:
5050 SMD
LED Qt. per Roll:
3000 pcs
IP Rating:
IP67
Pin Type:
4-pin
* Please do not carry load that exceeds specified output wattage to avoid over-load burn out.

Accessories
For Single Color Strip Light (2-pin)
110V-M-C-2PIN
(Direct use, does NOT need extra pins)
Middle Connector for single color
strip light (2-pin)
110V-L-C-2PIN
(Need extra two 2-pins)
LConnector for single color strip
light (2-pin)
For RGB Strip Light (4-pin)
110V-M-C-4PIN
(Need extra two 4-pins)
Middle Connector for single color
strip light (4-pin)
Universal Parts
110V-CLIP
Universal clear clip
110V-END-CAP
Universal clear end-cap
110V-GLUE
Connector/End-cap glue

POWER OFF BEFORE OPERATING!
UNROLL LIGHTS BEFORE POWERING ON!
Instructions
(1) Cut at cut-point
Step 1: Find the cut point –a clear gap between 2 sections.
Step 2: Power off, and cut in the middle of the cut-point at desired length.

(2) Connect to power (or controller)
Step 1: Insert 2-pin (or 4-pin for RGB strip) into strip light at cut-point.
Step 2: Insert part from ‘Step 1’ into power cord, or controller.
Arrow-head Side
Round-head Side

(3) Connect to another strip light
Step 1: Check pin type, 2-pin, 2-pin corner, or 4pin.
Step 2a: For single color strips, use 2-pin connector, or 2-pin corner connector with two 2-
Pins, and push light in firmly.
Step 2b: For RGB color strips, use 4-pin connector with two 4-Pins. First, insert 4-Pin into light,
then push light in firmly.
Arrow-head Side

(4) Close-up
Step 1: Glue the End-cap back to the end of strip light.
(5) Install lights
Step 1: Prepare clips. Two clips recommended for one section.
Step 2: Apply clips to strip light, and screw it using a screw driver.