Hitachi ZAXIS 110 Instruction manual

Manual No. : KM-187E
Vol. No. : W187E-02
Workshop Manual
Excavator
PRINTED IN SINGAPORE (PS)
110 120 125US 135US 135UR Excavator Workshop Manual
110 125US
120 135US
135UR
Service Manual (Manual No. KM-187E) consists of the following three separate volumes;
Technical Manual (Operational Principle) :Vol. No. TO187E
Technical Manual (Troubleshooting) :Vol. No. TT187E
Workshop Manual :Vol. No. W187E
Zaxis110/120/125US/135UR-WSh 6/3/02, 11:09 AM1
epcatalogs.com

INTRODUCTION
IN-01
TO THE READER
• This manual is written for an experienced technician
to provide technical information needed to maintain
and repair this machine.
• Be sure to thoroughly read this manual for correct
product information and service procedures.
• If you have any questions or comments, at if you
found any errors regarding the contents of this
manual, please contact using “Service Manual
Revision Request Form at the end of this man-
ual.
(Note: Do not tear off the form. Copy it for us-
age.):
Publications Marketing & Product Support
Hitachi Construction Machinery Co. Ltd.
TEL: [phone]
FAX: [phone]
ADDITIONAL REFERENCES
• Please refer to the materials listed below in addition
to this manual.
• The Operator’s Manual
• The Parts Catalog
• Operation Manual of the Engine
• Parts Catalog of the Engine
• Hitachi Training Material
MANUAL COMPOSITION
• This manual consists of three portions: the Techni-
cal Manual (Operational Principle), the Technical
Manual (Troubleshooting) and the Workshop Man-
ual.
• Information included in the Technical Manual
(Operational Principle):
technical information needed for redeliver and
delivery, operation and activation of all devices
and systems.
• Information included in the Technical Manual
(Troubleshooting):
technical information needed for operational per-
formance tests, and troubleshooting procedures.
• Information included in the Workshop Manual:
technical information needed for maintenance
and repair of the machine, tools and devices
needed for maintenance and repair, maintenance
standards, and removal/installation and assem-
ble/disassemble procedures.
PAGE NUMBER
• Each page has a number, located on the center
lower part of the page, and each number contains
the following information:
Example : T 1-3-5
Consecutive Page Number for Each Group
Group Number
Section Number
T: Technical Manual W: Workshop Manual
epcatalogs.com

INTRODUCTION
IN-02
SAFETY ALERT SYMBOL AND HEADLINE
NOTATIONS
In this manual, the following safety alert symbol and
signal words are used to alert the reader to the
potential for personal injury of machine damage.
This is the safety alert symbol. When you see this
symbol, be alert to the potential for personal injury.
Never fail to follow the safety instructions prescribed
along with the safety alert symbol.
The safety alert symbol is also used to draw attention
to component/part weights.
To avoid injury and damage, be sure to use appropri-
ate lifting techniques and equipment when lifting heavy
parts.
• CAUTION:
Indicated potentially hazardous situation which
could, if not avoided, result in personal injury or
death.
• IMPORTANT:
Indicates a situation which, if not conformed to the
instructions, could result in damage to the machine.
• NOTE:
Indicates supplementary technical information or
know-how.
UNITS USED
• SI Units (International System of Units) are used in
this manual.
MKS system units and English units are also
indicated in parenthheses just behind SI units.
Example : 24.5 MPa (250 kgf/cm2, 3560 psi)
A table for conversion from SI units to other system
units is shown below for reference purposees.
Quantity To Convert
From Into Multiply By
Pressure MPa kgf/cm210.197
MPa psi 145.0
Power kW PS 1.360
kW HP 1.341
Temperature °C°F°C×1.8+32
Velocity km/h mph 0.6214
min-1 rpm 1.0
Flow rate L/min US gpm 0.2642
mL/rev cc/rev 1.0
Quantity To Convert
From Into Multiply By
Length mm in 0.03937
mm ft 0.003281
L US gal 0.2642
Volume L US qt 1.057
m3yd31.308
Weight kg lb 2.205
Force N kgf 0.10197
N lbf 0.2248
Torque N⋅mkgf⋅m 1.0197
N⋅mlbf⋅ft 0.7375
epcatalogs.com

SAFETY
RECOGNIZE SAFETY INFORMATION
• This is the SAFETY ALERT SYMBOL.
• When you see this symbol on your machine or in
this manual, be alert to the potential for personal
injury.
• Follow recommended precautions and safe
operating practices.
001-E01A-0688
SA-688
UNDERSTAND SIGNAL WORDS
• On machine safety signs, signal words designating
the degree or level of hazard - DANGER, WARNING,
or CAUTION - are used with the safety alert symbol.
• DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
• WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
• CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury.
DANGER or WARNING safety signs are located
near specific hazards. General precautions are
listed on CAUTION safety signs.
• Some safety signs don’t use any of the
designated signal words above after the safety
alert symbol are occasionally used on this
machine.
• CAUTION also calls attention to safety messages in
this manual.
• To avoid confusing machine protection with personal
safety messages, a signal word IMPORTANT
indicates a situation which, if not avoided, could
result in damage to the machine.
• NOTE indicates an additional explanation for an
element of information.
002-E01C-1223
SA-1223
SA-1
epcatalogs.com

SAFETY
FOLLOW SAFETY INSTRUCTIONS
• Carefully read and follow all safety signs on the
machine and all safety messages in this manual.
• Safety signs should be installed, maintained and re-
placed when necessary.
• If a safety sign or this manual is damaged or
missing, order a replacement from your author-
ized dealer in the same way you order other
replacement parts (be sure to state machine
model and serial number when ordering).
• Learn how to operate the machine and its controls
correctly and safely.
• Allow only trained, qualified, authorized personnel to
operate the machine.
SA-003
• Keep your machine in proper working condition.
• Unauthorized modifications of the machine may
impair its function and/or safety and affect ma-
chine life.
• The safety messages in this SAFETY chapter are
intended to illustrate basic safety procedures of
machines. However it is impossible for these safety
messages to cover every hazardous situation you
may encounter. If you have any questions, you
should first consult your supervisor and/or your au-
thorized dealer before operating or performing
maintenance work on the machine.
003-E01B-0003
SA-2
epcatalogs.com

Buy now
Hitachi Excavator Zaxis 110, 120, 125US, 135US, 135UR Workshop
Manual PDF
With Instant Download