Hitachi G 14DMR User manual

Read through carefully and understand these instructions before use.
Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.
Διαβάστε προσεκτικά και κατανοήσετε αυτές τις οδηγίες πριν τη χρήση.
Przed użytkowaniem należy dokładnie przeczytaćniniejsząinstrukcjęi zrozumiećjej treść.
Használat előtt olvassa el figyelmesen a használati utasítást.
Před použitím si pečlivěpřečtěte tento návod a ujistěte se, že mu dobře rozumíte.
Aleti kullanmadan önce bu kılavuzu iyice okuyun ve talimatlarıanlayın.
Înainte de utilizare, citiţi cu atenţie și înţelegeţi prezentele instrucţiuni.
Pred uporabo natančno preberite in razumite ta navodila.
Pred použitím si dôkladne tieto pokyny prečítajte a pochopte ich.
Будь ласка, прочитайте інструкції іперевірте себе, чи все зрозуміло, перш ніж користуватися приладом.
Внимательно прочтите данную инструкцию по эксплуатации прежде чем пользоваться инструментом.
Handling instructions
Bedienungsanleitung
Οδηγίες χειρισμού
Instrukcja obsługi
Kezelési utasítás
Návod kobsluze
G 14DMR •G 14DL •G 18DMR •G 18DL
Kullanımtalimatları
Instrucţiuni de utilizare
Navodila za rokovanje
Pokyny na manipuláciu
Інструкції щодо поводження зпристроєм
Инструкция по эксплуатации
G18DL
Cordless Disc Grinder
Akku-Winkelschleifer
Γωνιακός τροχός
λειάνσεως μπαταρίας
Akumulatorowa
szlifierka kątowa
Akkus sarokcsiszoló
Akku úhlová bruska
Akülü taşlama
Polizor unghiular cu acumulator
Akumulatorski kotni brusilnik
Akku uhlová brúska
Акумуляторна кутова
шліфувальна машина
Аккумуляторная угловая
шлифовальная машина
000BookG14DMREE.indb1000BookG14DMREE.indb1 2012/04/2515:36:052012/04/2515:36:05

2
3 mm
15° – 30°
11.5 mm
1
3
2
4
5
7
6
8
9
!
^
0
#
@
%
$
AB
1
2
4
6
3
5
7
000BookG14DMREE.indb2000BookG14DMREE.indb2 2012/04/2515:36:062012/04/2515:36:06

3
English Deutsch Ελληνικά Polski
1Rechargeable battery Aufladbare Batterie Επαναφορτιζόμενη
μπαταρία Akumulator
2Latch Verriegelung Μάνδαλο Zapadka
3Pull out Herausziehen Τραβήξτε έξω Wyciągnij
4Insert Einsetzen Εισχωρήστε Włóż/wprowadź
5Wrench Schlüssel Κλειδί Klucz
6Wheel nut
Mutter für die Schleifscheibe Παξιμάδι τροχού Nakrętka tarczy
7Depressed center wheel Schleifscheibe Χαμηλωμένος κεντρικά
τροχός Obniżona tarcza środkowa
8Wheel washer Unterlegscheibe Ροδέλλα τροχού Podkładka tarczy
9Wheel guard Schutzhaube Προφυλακτήρας τροχού Osłona tarczy
0Spindle Spindel Άξονας Wrzeciono
!Push button Druckknopf Κουμπί ώθησης Przycisk
@Diamond wheel Diamantscheibe Διαμαντένιος τροχός Ściernica diamentowa
#Wear limit Verschleißgrenze Όριο φθοράς Ogranicznik zużycia
$Nail of carbon brush Klaue der Kohlebürste Καρφί καρβουνακιού Końcówka szczotek
węglowych
%Protrusion of carbon brush Krempe der Kohlebürste Προεξοχή καρβουνακιού Wypukłość elementu
węglowego
^Contact portion outside
brush tube Kontaktteil außerhalb des Bürstenrohrs Τμήμα επαφής έξω από το σωλήνα της ψήκτρας Element kontaktowy na zewnątrz komory szczotek
Magyar Čeština Türkçe Română
1Os tölthetőakkumulátor Akumulátor Şarj edilebilir batarya Acumulator reîncărcabil
2Retesz Zámek Mandal Element de blocare
3Kihúzni Zatáhnout Çekin Trageţi
4Bedugni Zasunout Yerleştirin Introduceţi
5Csavakulcs KlíčAnahtar Cheie
6Tárcsarögzítőanya Matka kotouče Disk somunu Piuliţă pentru disc
7Süllyesztett közepűtárcsa Brusný kotouč
Tek tarafıoyuk taşlama
diski
Disc cu centru depresat
8Tárcsa alátét Podložka kotouče Disk pulu Șaibăpentru disc
9TárcsavódőKryt kotouče Disk muhafazasıApărătoare pentru disc
0Tengely Hřídel Mill Ax
!Nyomógomb Tlačítko Kilit iğnesi Buton
@Gyémánt tárcsa Diamantový kotoučElmas disk Disc diamantat
#Megengedett kopás Mez opotřebení Aşınma sınırıLimităde uzură
$A szénkefe szöge Cvoček uhlíkového
kartáčku Kömür çivisi Capul periei din carbon
%A szénkefe kidudorodó
része Výstupek uhlíku Kömür çıkıntısıProeminenţa periei de
carbon
^Érintkezőrész a szénkefe
csövén kívül Dotyková část mimo trubičku kartáčku Kömür tüpünün dışındaki temas bölümü Porţiune de contact în exteriorul tubului periei
000TableG14DMREE.indd3000TableG14DMREE.indd3 2012/08/1011:00:162012/08/1011:00:16

4
Slovenščina Slovenčina Український Pyccкий
1Polnilni akumulator Nabíjateľný akumulátor Акумуляторна батарея Аккумуляторная батарея
2Zapah Západka Фіксатор Фиксатор
3Izvlecite Vytiahnuť Витягнути Вытащить
4Vstavite Zasunúť Вставити Вставить
5KljučKľúč Ключ Гаечный ключ
6Pesto kolesa Matica kotúčaГайка кріплення колеса
Гайка шлифовального круга
7Pritisnjeno osrednje kolo Kotúčs prelisom Шліфувальне коло із
заглибленим центром Шлифовальный круг с утопленным центром
8Blažilec kolesa Podložka kotúčaШайба
Шайба шлифовального круга
9Varovalo kolesa Ochranný kryt kotúčaКожух шліфувального
кола
Защитное приспособление
шлифовального круга
0Gred Hriadeľ Шпіндель Шпиндель
!Tipka Tlačidlo Аппаратна кнопка Нажимная кнопка
@Diamantno kolo Diamantový kotúčШліфувальний круг з
алмазною крайкою Шлифовальный круг с алмазной кромкой
#Meja obrabe Limit opotrebovania Межа зношування Предел износа
$Konica ogljikove ščetke Klinec uhlíkovej kefy Голка вугільної щітки Подпружиненный контакт
угольной щетки
%Izbočen del ogljikove
ščetke Posunutie uhlíkovej kefy Виступ вугільної щітки Выступающая часть угольной щетки
^Stični dekež izven cevi
ščetke Časťkontaktu mimo uhlíkovej kefy Поверхня контакту зовнішньої трубки щітки
Участок контакта
снаружи щеточной гильзы
000BookG14DMREE.indb4000BookG14DMREE.indb4 2012/04/2515:36:072012/04/2515:36:07

5
Symbols
WARNING
The following show symbols
used for the machine. Be
sure that you understand their
meaning before use.
Symbole
WARNUNG
Die folgenden Symbole werden
für diese Maschine verwendet.
Achten Sie darauf, diese vor der
Verwendung zu verstehen.
Σύμβολα
ΠΡΟΣΟΧΗ
Τα παρακάτω δείχνουν τα
σύμβολα που χρησιμοποιούνται
στο μηχάνημα. Βεβαιωθείτε ότι
κατανοείτε τη σημασίας τους
πριν τη χρήση.
Symbole
OSTRZEŻENIE
Następujące oznaczenia to
symbole używane w instrukcji
obsługi maszyny. Upewnij się, że
rozumiesz ich znaczenie zanim
użyjesz narzędzia.
Read all safety warnings and
all instructions.
Failure to follow the warnings
and instructions may result
in electric shock, fire and/or
serious injury.
Lesen Sie sämtliche
Sicherheitshinweise und
Anweisungen durch.
Wenn die Warnungen
und Anweisungen nicht
befolgt werden, kann es zu
Stromschlag, Brand und/
oder ernsthaften Verletzungen
kommen.
Διαβάζετε όλες τις
προειδοποιήσεις ασφαλείας
και όλες τις οδηγίες.
Ημη τήρηση των
προειδοποιήσεων και οδηγιών
μπορεί να προκαλέσει
ηλεκτροπληξία, πυρκαγιά και/ή
σοβαρό τραυματισμό.
Należydokładnie zapoznaćsię
ze wszystkimi ostrzeżeniami i
wskazówkami bezpieczeństwa.
Nieprzestrzeganie ostrzeżeń
oraz wskazówek bezpieczeństwa
może spowodowaćporażenie
prądem elektrycznym, pożar i/lub
odniesienie poważnych obrażeń.
Always wear eye protection. Tragen Sie immer einen
Augenschutz.
Φοράτε πάντα τον κατάλληλο
εξοπλισμό για την προστασία
των ματιών.Zawsze nosićokulary ochronne.
Only for EU countries
Do not dispose of electric tools
together with household waste
material!
In observance of European
Directive 2002/96/EC
on waste electrical and
electronic equipment and its
implementation in accordance
with national law, electric tools
that have reached the end
of their life must be collected
separately and returned to an
environmentally compatible
recycling facility.
Nur für EU-Länder
Werfen Sie Elektrowerkzeuge
nicht in den Hausmüll!
Gemäss Europäischer
Richtlinie 2002/96/EG über
Elektro- und Elektronik-
Altgeräte und Umsetzung
in nationales Recht müssen
verbrauchte Elektrowerkzeuge
getrennt gesammelt und
einer umweltgerechaten
Wiederververtung zugeführt
werden.
Μόνο για τις χώρες της ΕΕ
Μην πετάτε τα ηλεκτρικά
εργαλεία στον κάδο οικιακών
απορριμμάτων!
Σύμφωνα με την ευρωπαϊκή
οδηγία 2002/ 96/ΕΚ περί
ηλεκτρικών και ηλεκτρονικών
συσκευών και την ενσωμάτωσή
της στο εθνικό δίκαιο, τα
ηλεκτρικά εργαλεία πρέπει
να συλλέγονται ξεχωριστά
και να επιστρέφονται για
ανακύκλωση με τρόπο φιλικό
προς το περιβάλλον.
Dotyczy tylko państw UE
Nie wyrzucaj elektronarzędzi
wraz z odpadami z gospodarstwa
domowego!
Zgodnie z EuropejskąDyrektywą
2002/96/WE w sprawie zużytego
sprzętu elektrotechnicznego
i elektronicznego oraz
dostosowaniem jej do
prawa krajowego, zużyte
elektronarzędzia należy
posegregowaći zutylizowaćw
sposób przyjazny dla środowiska.
Jelölések
FIGYELEM
Az alábbiakban a géphez
alkalmazott jelölések vannak
felsorolva. A gép használata
előtt feltétlenül ismerje meg
ezeket a jelöléseket.
Symboly
UPOZORNĚNÍ
Následující text obsahuje
symboly, které jsou použity na
zařízení. Ujistěte se, že rozumíte
jejich obsahu před tím, než
začnete zařízení používat.
Simgeler
DİKKAT
Aşağıda, bu alet için kullanılan
simgeler gösterilmiştir.
Aleti kullanmadan önce bu
simgelerin ne anlama geldiğini
anladığınızdan emin olun.
Simboluri
AVERTISMENT
În cele ce urmeazăsunt
prezentate simbolurile folosite
pentru mașină. Înainte de
utilizare, asiguraţi-văcăînţelegeţi
semnificaţia acestora.
Olvasson el minden
biztonsági figyelmeztetést és
minden utasítást.
A figyelmeztetések és
utasítások be nem tartása
áramütést, tüzet és/vagy súlyos
sérülést eredményezhet.
Přečtěte si všechna varování
týkající se bezpečnosti a
všechny pokyny.
Nedodržení těchto varování a
pokynůmůže mít za následek
elektrický šok, požár a/nebo
vážné zranění.
Tüm güvenlik uyarılarını ve
tüm talimatları okuyun.
Uyarılara ve talimatlara
uyulmamasıelektrik
çarpmasına, yangına ve/veya
ciddi yaralanmaya neden
olabilir.
Citiţitoate avertismentele
privind siguranţașitoate
instrucţiunile.
Nerespectarea avertismentelor
și a instrucţiunilor poate avea
ca efect producerea de șocuri
electrice, incendii și/sau vătămări
grave.
Mindig viseljen
Védőszemüveget. Vždy noste ochranu očí Daima koruyucu gözlük takın. Purtaţi întotdeauna protecţie pentru ochi
Csak EU-országok számára Az
elektromos kéziszerszámokat
ne dobja a háztartási szemétbe!
A használt villamos és
elektronikai készülékekről szóló
2002/96/EK irányelv és annak
a nemzeti jogba való átültetése
szerint az elhasznált elektromos
kéziszerszámokat külön kell
gyűjteni, és környezetbarát
módon újra kell hasznosítani.
Jen pro státy EU Elektrické
nářadí nevyhazujte do
komunálního odpadu!
Podle evropské směrnice
2002/96/EG o nakládání
s použitými elektrickými a
elektronickými zařízeními a
odpovídajících ustanovení
právních předpisůjednotlivých
zemí se použitá elektrická
nářadí musí sbírat odděleně
od ostatního odpadu a
podrobit ekologicky šetrnému
recyklování.
Sadece AB ülkeleri için Elektrikli
el aletlerini evdeki çöp kutusuna
atmayınız!
Kullanılmışelektrikli aletleri,
elektrik ve elektronikli eski
cihazlar hakkındaki 2002/96/
EC Avrupa yönergelerine göre
ve bu yönergeler ulusal hukuk
kurallarına göre uyarlanarak,
ayrıolarak toplanmalıve çevre
şartlarına uygun bir şekilde
tekrar değerlendirmeye
gönderilmelidir.
Numai pentru ţările membre UE
Nu aruncaţi aceastăsculă
electricăîmpreunăcu deșeurile
menajere!
În conformitate cu Directiva
Europeană2002/96/CE
referitoare la deșeurile
reprezentând echipamente
electrice și electronice și la
implementarea acesteia în
conformitate cu legislaţiile
naţionale, sculele electrice
care au ajuns la finalul duratei
de folosire trebuie colectate
separat și duse la o unitate de
reciclare compatibilăcu mediul
înconjurător.
000BookG14DMREE.indb5000BookG14DMREE.indb5 2012/04/2515:36:072012/04/2515:36:07

6
Simboli
OPOZORILO
V nadaljevanju so prikazani
simboli, uporabljeni pri stroju.
Pred uporabo se prepričajte, da
jih razumete.
Symboly
VÝSTRAHA
V nasledujúcom sú zobrazené
symboly, ktoré sú vyobrazené
na náradí. Pred použitím náradia
sa oboznámte s významom
týchto symbolov.
Символи
ПОПЕРЕДЖЕННЯ
Тут показані символи,
використані вкерівництві.
Будь ласка, переконайтеся,
що правильно розумієте їхнє
значення.
Символы
ПРЕДУПРЕЖДЕНИЕ
Ниже приведены символы,
используемые для машины.
Перед началом работы
обязательно убедитесь втом,
что Вы понимаете их значение.
Preberite vas varnostna
opozorila in navodila.
Z neupoštevanjem opozoril
in navodil tvegate električni
udar, požar in/ali resne telesne
poškodbe.
Prečítajte si všetky
bezpečnostné výstrahy a
všetky pokyny.
Nedodržanie výstrah a
pokynov môže viesťk
zasiahnutiu elektrickým
prúdom, požiaru a/alebo
vážnemu poraneniu osoby.
Прочитайте всі правила
безпеки та вказівки.
Невиконання цих правил
та інструкцій може
призвести до удару
струмом, пожежі та/або
серйозної травми.
Прочтите все правила
безопасности и
инструкции.
Не выполнение правил
иинструкций может
привести кпоражению
электрическим током,
пожару и/или серьезной
травме.
Uporaba zaščite za oči je
obvezna. V
ž dy noste ochranu na oči. З
авж д и носіть захисні
окуляри.Всегда надева
й те сред ст ва
э ащиты гла э.
Samo za države EU
Električnih orodij ne zavržite
skupaj z gospodinjskimi
odpadki!
V skladu z evropsko direktivo
2002/96/EC o odpadni električni
in elektronski opremi in izvedbi
v skladu z državnimi zakoni,
je treba električna orodja, ki
so dosegla življenjsko dobo
ločeno zbirati in vrniti v z
okoljem združljivo ustanovo za
recikliranje.
Iba pre krajiny EÚ
Elektrické náradie nezneškodňujte
spolu s komunálnym odpadom z
domácností!
Aby ste dodržali ustanovenia
európskej smernice 2002/96/
ES o odpadových elektrických a
elektronických zariadeniach a jej
implementáciu v zmysle národnej
legislatívy, je potrebné elektrické
zariadenie po uplynutí jeho doby
životnosti separovaťa doručiťna
environmentálne prijateľné miesto
recyklovania.
Лише для країн ЄС
НЕ викидайте електричні
інструменти із побутовими
відходами!
Згідно Європейської
Директиви 2002/96/EC про
відходи електронного та
електричного виробництва
іїї запровадження
згідно місцевих законів,
електроінструменти, які
відслужили робочий строк
слід утилізувати окремо і
повертати до установ, що
займаються екологічною
переробкою брухту.
Только для стран ЕС
Не выкидывайте
электроприборы вместе с
обоычным мусором!
Всоответствии севропейской
директивой 2002/96/ЕС
об утилизации старых
электрических иэлектронных
приборов ивсоответствии
сместными законами
электроприборы, бывщие
вэксплуатации, должны
утилизовываться отдельно
безопасным для окружающей
среды способом.
000BookG14DMREE.indb6000BookG14DMREE.indb6 2012/04/2515:36:072012/04/2515:36:07

7
English
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodified plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the
risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase the risk
of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.
b) Use personal protective equipment. Always wear
eye protection.
Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the switch
is in the off position before connecting to power
source and/or battery pack, picking up or
carrying the tool.
Carrying power tools with your finger on the
switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off.
Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the risk
of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tools operation.
If damaged, have the power tool repaired before
use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, taking
into account the working conditions and the
work to be performed.
Use of the power tool for operations different from
those intended could result in a hazardous situation.
(Original instructions)
01Eng_G14DMR_EE 4/25/12, 15:137

8
English
5) Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer.
A charger that is suitable for one type of battery
pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically designated
battery packs.
Use of any other battery packs may create a risk
of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects like paper clips, coins,
keys, nails, screws, or other small metal objects
that can make a connection from one terminal
to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause
irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool
is maintained.
PRECAUTION
Keep children and infirm persons away.
When not in use, tools should be stored out of reach of
children and infirm persons.
SAFETY WARNINGS COMMON FOR
GRINDING OR ABRASIVE CUTTING-OFF
OPERATIONS
a) This power tool is intended to function as a grinder
or cut-off tool. Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
b) Operations such as sanding, wire brushing or
polishing are not recommended to be performed
with this power tool.
Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
c) Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
d) The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool.
Accessories running faster than their rated speed
can break and fly apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
f) The arbour size of wheels, flanges, backing pads
or any other accessory must properly fit the spindle
of the power tool.
Accessories with arbour holes that do not match
the mounting hardware of the power tool will run
out of balance, vibrate excessively and may cause
loss of control.
g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
the rotating accessory and run the power tool at
maximum no-load speed for one minute.
Damaged accessories will normally break apart
during this test time.
h) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping
flying debris generated by various operations. The
dust mask or respirator must be capable of filtrating
particles generated by your operation.
Prolonged exposure to high intensity noise may
cause hearing loss.
i) Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment.
Fragments of workpiece or of a broken accessory
may fly away and cause injury beyond immediate
area of operation.
j) Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord.
Cutting accessory contacting a ”live” wire may make
exposed metal parts of the power tool “live” and
shock the operator.
k) Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the
spinning accessory.
l) Never lay the power tool down until the accessory
has come to a complete stop.
The spinning accessory may grab the surface and
pull the power tool out of your control.
m) Do not run the power tool while carrying it at your
side.
Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your
body.
n) Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside the housing
and excessive accumulation of powdered metal may
cause electrical hazards.
o) Do not operate the power tool near flammable
materials.
Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
01Eng_G14DMR_EE 4/25/12, 15:138

9
English
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged
rotatingwheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power
toolto be forcedin the directionopposite of theaccessory’s
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering
into the pinch point can dig into the surface of the material
causing the wheel to climb out or kick out. The wheel may
either jump toward or away from the operator, depending
on direction of the wheel’s movement at the point of
pinching. Abrasive wheels may also break under these
conditions.
Kickbackis the result ofpower tool misuse and/or incorrect
operating procedures or conditions and can be avoided
by taking proper precautions as given below.
a) Maintain a firm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided, for
maximum control over kickback or torque reaction
during start-up.
The operator can control torque reactions or kickback
forces, if proper precautions are taken.
b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c) Do not position your body in the area where power
tool will move if kickback occurs.
Kickback will propel the tool in direction opposite
to the wheel’s movement at the point of snagging.
d) Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency
to snag the rotating accessory and cause loss of
control or kickback.
e) Do not attach a saw chain woodcarving blade or
toothed saw blade.
Such blades create frequent kickback and loss of
control.
SAFETY WARNINGS SPECIFIC FOR
GRINDING AND ABRASIVE CUTTING-OFF
OPERATIONS
a) Use only wheel types that are recommended for
your power tool and the specific guard designed
for the selected wheel.
Wheels for which the power tool was not designed
cannot be adequately guarded and are unsafe.
b) The guard must be securely attached to the power
tool and positioned for maximum safety, so the
least amount of wheel is exposed towards the
operator.
The guard helps to protect operator from broken
wheel fragments and accidental contact with wheel.
c) Wheels must be used only for recommended
applications. For example: do not grind with the
side of cut-off wheel.
Abrasive cut-off wheels are intended for peripheral
grinding, side forces applied to these wheels may
cause them to shatter.
d) Always use undamaged wheel flanges that are of
correct size and shape for your selected wheel.
Proper wheel flanges support the wheel thus
reducing the possibility of wheel breakage. Flanges
for cut-off wheels may be different from grinding
wheel flanges.
e) Do not use worn down wheels from larger power
tools.
Wheel intended for larger power tool is not suitable
for the higher speed of a smaller tool and may
burst.
ADDITIONAL SAFETY WARNINGS SPECIFIC
FOR ABRASIVE CUTTING-OFF OPERATIONS
a) Do not “jam” the cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive
depth of cut.
Overstressing the wheel increases the loading and
susceptibility to twisting or blinding of the wheel
in the cut and the possibility of kickback or wheel
breakage.
b) Do not position your body in line with and behind
the rotating wheel.
When the wheel, at the point of operation, is moving
away from your body, the possible kickback may
propel the spinning wheel and the power tool directly
at you.
c) When wheel is binding or when interrupting a cut
for any reason, switch off the power tool and hold
the power tool motionless until the wheel comes
to a complete stop. Never attempt to remove the
cut-off wheel from the cut while the wheel is in
motion otherwise kickback may occur.
Investigate and take corrective action to eliminate
the cause of wheel binding.
d) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully reenter the cut.
The wheel may bind, walk up or kickback if the
power tool is restarted in the workpiece.
e) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own
weight. Supports must be placed under the
workpiece near the line of cut and near the edge
of the workpiece on both sides of the wheel.
f) Use extra caution when making a “pocket cut” into
existing walls or other blind areas.
The protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kickback.
GENERAL SAFETY INSTRUCTIONS FOR
CORDLESS DISC GRINDERS
–Check that speed marked on the wheel is equal to
or greater than the rated speed of the grinder;
–Ensure that the wheel dimensions are compatible
with the grinder;
–Abrasive wheels shall be stored and handled with
care in accordance with manufacturer’s instructions;
–Inspect the grinding wheel before use, do not use
chipped, cracked or otherwise defective products;
01Eng_G14DMR_EE 4/25/12, 15:139

10
English
–Ensure that mounted wheels and points are fitted
in accordance with the manufacturer’s instructions;
–Ensure that blotters are used when they are provided
with the bonded abrasive product and when they
are required;
–Ensure that the abrasive product is correctly mounted
and tightened before use and run the tool at no-
load for 30 s in a safe position, stop immediately
if there is considerable vibration or if other defects
are detected. If this condition occurs, check the
machine to determine the cause;
–If a guard is equipped with the tool never use the
tool without such a guard;
–Do not use separate reducing bushings or adapters
to adapt large hole abrasive wheels;
–For tools intended to be fitted with threaded hole
wheel, ensure that the thread in the wheel is long
enough to accept the spindle length;
–Check that the work piece is properly supported;
–Do not use cutting off wheel for side grinding;
–Ensure that sparks resulting from use do not create
a hazard e.g. do not hit persons, or ignite flammable
substances;
–Ensure that ventilation openings are kept clear when
working in dusty conditions, if it should become
necessary to clear dust, first disconnect the tool
from the mains supply (use non metallic objects)
and avoid damaging internal parts;
–Always use eye and ear protection. Other personal
protective equipment such as dust mask, gloves,
helmet and apron should be worn;
–Pay attention to the wheel that continues to rotate
after the tool is switched off.
–Always charge the battery at a temperature of 0
– 40°C.
A temperature of less than 0°C will result in over
charging which is dangerous. The battery cannot
be charged at a temperature greater than 40°C.
The most suitable temperature for charging is that
of 20 – 25°C.
–Do not use the charger continuously.
When one charging is completed, leave the charger
for about 15 minutes before the next charging of
battery.
–Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
–Never disassemble the rechargeable battery and
charger.
–Never short-circuit the rechargeable battery.
Short-circuiting the battery will cause a great electric
current and overheat. It results in burn or damage
to the battery.
–Do not dispose of the battery in fire.
If the battery burnt, it may explode.
–Do not insert object into the air ventilation slots of
the charger.
Inserting metal objects or inflammables into the
charger air ventilation slots will result in electrical
shock hazard or damaged charger.
–Bring the battery to the shop from which it was
purchased as soon as the post-charging battery life
becomes too short for practical use. Do not dispose
of the exhausted battery.
–Using an exhausted battery will damage the charger.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips
with the protection function to stop the output.
In the cases of 1 and 2 described below, when using
this product, even if you are pulling the switch, the
motor may stop. This is not the trouble but the result
of protection function.
1. When the battery power remaining runs out (The
battery voltage drops to about 12V (G18DL) /
about 8V (G14DL)), the motor stops.
In such case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In
this case, release the switch of tool and eliminate
causes of overloading. After that, you can use it
again.
Furthermore, please heed the following warning and
caution.
WARNING
In order to prevent any battery leakage, heat generation,
smoke emission, explosion and ignition beforehand,
please be sure to heed the following precautions.
1. Make sure that swarf and dust do not collect on
the battery.
䡬During work make sure that swarf and dust do
not fall on the battery.
䡬Make sure that any swarf and dust falling on the
power tool during work do not collect on the
battery.
䡬Do not store an unused battery in a location
exposed to swarf and dust.
䡬Before storing a battery, remove any swarf and
dust that may adhere to it and do not store it
together with metal parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such
as a nail, strike with a hammer, step on, throw
or subject the battery to severe physical shock.
3. Do not use an apparently damaged or deformed
battery.
4. Do not use the battery in reverse polarity.
5. Do not connect directly to an electrical outlets or
car cigarette lighter sockets.
6. Do not use the battery for a purpose other than
those specified.
7. If the battery charging fails to complete even
when a specified recharging time has elapsed,
immediately stop further recharging.
8. Do not put or subject the battery to high
temperatures or high pressure such as into a
microwave oven, dryer, or high pressure container.
9. Keep away from fire immediately when leakage
or foul odor are detected.
10. Do not use in a location where strong static
electricity generates.
11. If there is battery leakage, foul odor, heat
generated, discolored or deformed, or in any way
appears abnormal during use, recharging or
storage, immediately remove it from the equipment
or battery charger, and stop use.
CAUTION
1. If liquid leaking from the battery gets into your
eyes, do not rub your eyes and wash them well
with fresh clean water such as tap water and
contact a doctor immediately.
If left untreated, the liquid may cause eye-problems.
01Eng_G14DMR_EE 4/25/12, 15:1310