Hitachi CP-X8150 User manual

1
Projector
CP-X8150/CP-X8160/
CP-WX8240/CP-WX8255/
CP-SX8350/CP-WU8440/CP-WU8450
User's Manual (detailed)
Operating Guide – Technical
Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode
720 x 400 37.9 85.0 VESA TEXT
640 x 480 31.5 59.9 VESA VGA (60Hz)
640 x 480 37.9 72.8 VESA VGA (72Hz)
640 x 480 37.5 75.0 VESA VGA (75Hz)
640 x 480 43.3 85.0 VESA VGA (85Hz)
800 x 600 35.2 56.3 VESA SVGA (56Hz)
800 x 600 37.9 60.3 VESA SVGA (60Hz)
800 x 600 48.1 72.2 VESA SVGA (72Hz)
800 x 600 46.9 75.0 VESA SVGA (75Hz)
800 x 600 53.7 85.1 VESA SVGA (85Hz)
832 x 624 49.7 74.5 Mac 16” mode
1024 x 768 48.4 60.0 VESA XGA (60Hz)
1024 x 768 56.5 70.1 VESA XGA (70Hz)
1024 x 768 60.0 75.0 VESA XGA (75Hz)
1024 x 768 68.7 85.0 VESA XGA (85Hz)
1152 x 864 67.5 75.0 VESA
1152 x 864 (75Hz)
1280 x 768 47.7 60.0 VESA W-XGA (60Hz)
1280 x 800 49.7 60.0 VESA
1280 x 800 (60Hz)
1280 x 960 60.0 60.0 VESA 1280 x 960 (60Hz)
1280 x 1024 64.0 60.0 VESA SXGA (60Hz)
1280 x 1024 80.0 75.0 VESA SXGA (75Hz)
1440 x 900 55.9 59.9 VESA WXGA+ (60Hz)
Example of computer signal
(continued on next page)

2
Example of computer signal
Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode
*1 1280 x 1024 91.1 85.0 VESA SXGA (85Hz)
*2 1400 x 1050 65.2 60.0 VESA SXGA+ (60Hz)
*3 1680 x 1050 65.3 60.0 VESA WSXGA+ (60Hz)
*1 1600 x 1200 75.0 60.0 VESA UXGA (60Hz)
*4 1920 x 1200 74.0 60.0 VESA W-UXGA (60Hz)
Reduced Blanking
*1) Supported except for HDMITM input.
*2) Only for CP-X8150, CP-X8160 and CP-SX8350.
*3) Only for CP-WX8240, CP-WX8255, CP-WU8440 and CP-WU8450.
*4) Only for CP-WU8440 and CP-WU8450, but except for HDMITM input.
NOTE • Be sure to check jack type, signal level, timing and resolution
before connecting this projector to a computer.
• Some computers may have multiple display screen modes. Use of some of
these modes will not be possible with this projector.
• Depending on the input signal, full-size display may not be possible in some
cases. Refer to the number of display pixels above.
• Although the projector can display signals with resolution up to UXGA
(1600x1200) or with W-UXGA only for CP-WU8440 and CP-WU8450, the
signal will be converted to the projector’s panel resolution before being
displayed. The best display performance will be achieved if the resolutions of
the input signal and projector panel are identical.
• Automatic adjustment may not function correctly with some input signals.
• The image may not be displayed correctly when the input sync signal is a
composite sync or a sync on G.

3
Initial set signals
Back porch (B) Front porch (D) Back porch (b) Front porch (d)
Active video (C)
Data Data
H. Sync. V. Sync.
Sync (A) Sync (a)
Active video (c)
Resolution
(H x V)
Horizontal signal timing (μs) Vertical signal timing (lines) Signal mode
(A) (B) (C) (D) (a) (b) (c) (d)
720 x 400 2.0 3.0 20.3 1.0 3 42 400 1 TEXT
640 x 480 3.8 1.9 25.4 0.6 2 33 480 10 VGA (60Hz)
640 x 480 1.3 4.1 20.3 0.8 3 28 480 9 VGA (72Hz)
640 x 480 2.0 3.8 20.3 0.5 3 16 480 1 VGA (75Hz)
640 x 480 1.6 2.2 17.8 1.6 3 25 480 1 VGA (85Hz)
800 x 600 2.0 3.6 22.2 0.7 2 22 600 1 SVGA (56Hz)
800 x 600 3.2 2.2 20.0 1.0 4 23 600 1 SVGA (60Hz)
800 x 600 2.4 1.3 16.0 1.1 6 23 600 37 SVGA (72Hz)
800 x 600 1.6 3.2 16.2 0.3 3 21 600 1 SVGA (75Hz)
800 x 600 1.1 2.7 14.2 0.6 3 27 600 1 SVGA (85Hz)
832 x 624 1.1 3.9 14.5 0.6 3 39 624 1 Mac 16" mode
1024 x 768 2.1 2.5 15.8 0.4 6 29 768 3 XGA (60Hz)
1024 x 768 1.8 1.9 13.7 0.3 6 29 768 3 XGA (70Hz)
1024 x 768 1.2 2.2 13.0 0.2 3 28 768 1 XGA (75Hz)
1024 x 768 1.0 2.2 10.8 0.5 3 36 768 1 XGA (85Hz)
1152 x 864 1.2 2.4 10.7 0.6 3 32 864 1 1152 x 864
(75Hz)
1280 x 768 1.7 2.5 16.0 0.8 3 23 768 1 W-XGA (60Hz)
1280 x 800 1.6 2.4 15.3 0.8 3 24 800 1 1280 x 800
(60Hz)
1280 x 960 1.0 2.9 11.9 0.9 3 36 960 1 1280 x 960
(60Hz)
1280 x 1024 1.0 2.3 11.9 0.4 3 38 1024 1 SXGA (60Hz)
1280 x 1024 1.1 1.8 9.5 0.1 3 38 1024 1 SXGA (75Hz)
1280 x 1024 1.0 1.4 8.1 0.4 3 44 1024 1 SXGA (85Hz)
1400 x 1050 1.2 2.0 11.4 0.7 3 33 1050 1 SXGA+ (60Hz)
1440 x 900 1.4 2.2 13.5 0.8 6 25 900 3 WXGA+ (60Hz)
1680 x 1050 1.2 1.9 11.5 0.7 6 30 1050 3 WSXGA+ (60Hz)
1600 x 1200 1.2 1.9 9.9 0.4 3 46 1200 1 UXGA (60Hz)
1920 x 1200 0.208 0.519 12.47 0.312 6 26 1200 3 W-UXGA (60Hz)
Reduced Blanking
The following signals are used for the initial settings. The signal timing of some
computer models may be different. In such case, adjust the items V POSITION
and H POSITION in the IMAGE menu.
Initial set signals

4
ACOMPUTER IN1, BMONITOR OUT
D-sub 15pin mini shrink jack
<Computer signal>
• Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive)
• H/V. sync. signal: TTL level (positive/negative)
• Composite sync. signal: TTL level
<Component video signal>
• Video signal: Y with composite sync, Analog, 1.0±0.1Vp-p, 75Ω terminated
Cb/Pb, Analog, 0.7±0.1Vp-p, 75Ω terminated
Cr/Pr, Analog, 0.7±0.1Vp-p 75Ω terminated
• System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60
Pin Signal Pin Signal
1Video Red, Cr/Pr 9(No connection)
2Video Green, Y 10 Ground
3Video Blue, Cb/Pb 11 (No connection)
4(No connection) 12 A: SDA (DDC data) B: (No connection)
5 Ground 13 H. sync / Composite sync.
6Ground Red, Ground Cr/Pr 14 V. sync.
7Ground Green, Ground Y 15 A: SCL (DDC clock) B: (No connection)
8Ground Blue, Ground Cb/Pb
Connection to the ports
① ⑤④③②
⑥ ⑩⑨⑧⑦
⑪ ⑮⑭⑬⑫ ①⑤④③②
⑥⑩ ⑨ ⑧ ⑦
⑪⑮⑭⑬⑫
Connection to the ports
B
A
NOTICE ►Use the cables with straight plugs, not L-shaped ones, as the
input ports of the projector are recessed.
►Only the signal that is input from the COMPUTER IN1 or IN2 can be output
from the MONITOR OUT port.

5
Connection to the ports (continued)
COMPUTER IN2 CG/Y, DB/Cb/Pb, ER/Cr/Pr, FH, GV
BNC jack x5
<Computer signal>
• Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive)
• H/V. sync. signal: TTL level (positive/negative)
• Composite sync. signal: TTL level
<Component video signal>
• Video signal: Y with composite sync, Analog, 1.0±0.1Vp-p, 75Ω terminated
Cb/Pb, Analog, 0.7±0.1Vp-p, 75Ω terminated
Cr/Pr, Analog, 0.7±0.1Vp-p 75Ω terminated
• System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60
HHDMI 1, IHDMI 2
HDMITM connector
• Audio signal: Linear PCM (Sampling rate; 32/44.1/48 kHz)
Pin Signal Pin Signal Pin Signal
1 T.M.D.S. Data2 + 8 T.M.D.S. Data0 Shield 15 SCL
2T.M.D.S. Data2 Shield 9 T.M.D.S. Data0 - 16 SDA
3 T.M.D.S. Data2 - 10 T.M.D.S. Clock + 17 DDC/CEC Ground
4 T.M.D.S. Data1 + 11 T.M.D.S. Clock Shield
18 +5V Power
5T.M.D.S. Data1 Shield 12 T.M.D.S. Clock - 19 Hot Plug Detect
6 T.M.D.S. Data1 - 13 CEC
7 T.M.D.S. Data0 + 14 Reserved (N.C. on device)
① ⑤
④
③
②⑥⑩
⑨
⑧
⑦⑪⑮
⑭
⑬
⑫
⑲
⑱
⑰
⑯①⑤
④
③
②⑥⑩
⑨
⑧
⑦⑪⑮
⑭
⑬
⑫
⑲
⑱
⑰
⑯
C ED
F
F G
H I

6
MS-VIDEO
Mini DIN 4pin jack
• S-video signal, Analog:
-Brightness signal with composite sync, 1.0±0.1Vp-p, 75Ω terminated
-Color signal, 0.286Vp-p (NTSC, burst), 75Ω terminated
0.300Vp-p (PAL/SECAM, burst) 75Ω terminated
• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL(60Hz)
Pin Signal
1 C (color signal)
2Y (brightness signal)
3 Ground
4 Ground
Connection to the ports (continued)
NVIDEO
RCA jack
• Composite video signal, Analog, 1.0±0.1Vp-p, 75Ω terminator
• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL(60Hz)
COMPONENT JY, KCb/Pb, LCr/Pr
RCA jack x3
• Component video signal, Analog:
-Y with composite sync, 1.0±0.1Vp-p, 75Ω terminated
-Cb/Pb, 0.7±0.1Vp-p, 75Ω terminated
-Cr/Pr, 0.7±0.1Vp-p 75Ω terminated
• System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60, 1080p@50/60
L JK
MN
①
④ ③
②
①
④③
②
1
2
3
4

7
Connection to the ports (continued)
OAUDIO IN1, PAUDIO IN2
Ø3.5 stereo mini jack
•
Analog, 500 mVrms, 47kΩ input impedance
AUDIO IN3 QL, RR AUDIO OUT SL, TR
RCA jack x2 RCA jack x2
•
Analog, 500 mVrms, 47kΩ input impedance • Analog, 500 mVrms, 1kΩ output impedance
U
CONTROL
D-sub 9pin plug
* About the details of RS-232C communication,
please refer to the next section.
Pin Signal Pin Signal Pin Signal
1(No connection) 4(No connection) 7 RTS
2 RD 5 Ground 8 CTS
3 TD 6 (No connection) 9(No connection)
① ②
⑥⑦⑧⑨
⑤④③
①②
⑥⑦⑧⑨
⑤④③
O
P
S T
RQ
U

8
REMOTE CONTROL YIN, ZOUT
Ø3.5 stereo mini jack
Connection to the ports (continued)
X
USB TYPE B
USB B type jack
Pin Signal
1 +5V
2 - Data
3+ Data
4Ground
V
LAN
RJ-45 jack
* About the details of network communication,
please refer to the Network Guide.
Pin Signal Pin Signal Pin Signal
1 TX+ 4 - 7 -
2 TX- 5 - 8 -
3RX+ 6 RX-
WUSB TYPE A
USB A type jack x2
Pin Signal
1 +5V
2 - Data
3+ Data
4Ground
①
④③
②
①
④③
②
① ⑤
④
③
② ⑥ ⑧
⑦①⑤
④
③
②⑥⑧
⑦
① ④③②
①④ ③ ②
① ④③②
①④ ③ ②
WX
YZ
V

9
To input SCART RGB signal;
ex.
Video
G
B
R
Audio L
Audio R
Connection to the ports (continued)
To input SCART RGB signal to the projector, use a SCART to RCA cable.
Connect the plugs refer to above ex. For more reference, please consult your
dealer.
SCART
connector
(jack)
SCART cable
(plug)
RCA plugs

10
① ②
⑥⑦⑧⑨
⑤④③
①②
⑥⑦⑧⑨
⑤④③
CD (1) (1) －
RD(2) (2) RD
TD (3) (3) TD
DTR (4) (4) －
GND (5) (5) GND
DSR (6) (6) －
RTS (7) (7) RTS
DTS (8) (8) CTS
RI (9) (9) －
RS-232C Communication
RS-232C Communication
When the projector connects to the computer by RS-232C communication, the
projector can be controlled with RS-232C commands from the computer.
For details of RS-232C commands, refer to RS-232C Communication / Network
command table (&19).
Connection
1. Turn off the projector and the computer.
2. Connect the projector's CONTROL port and the computer's RS-232C port
with a RS-232C cable (cross). Use the cable that ful lls the speci cation
shown in  gure
3. Turn the computer on, and after the computer has started up turn the projector
on.
4. Set the COMMUNICATION TYPE to OFF in the COMMUNICATION menu of the
OPTION - SERVICE menu.
1
9876
5432
1
9876
5432
CONTROL port
of the projector
RS-232C port
of the computer
RS-232C cable
(cross)
RS-232C CONTROL