Hizero F801 User manual
4-in-1 Bionic Mop
4-in-1 Bionic Mop (F801)
User Manual
www.hizero.com
Bringing the
World into
Bionic Cleaning
Era
1
Take out the trash container Open the cleaning head cover to take out the trash container.
Insert the cleaning roller
Insert the battery
Place the lower body on its side, nd the drive motor and gently pull it out to a right angle (not to exceed 45°), insert
the cleaning roller onto the drive motor, then push into the cleaning head till the lateral button in place.
Note:
1. For the rst use, make sure to soak the cleaning roller till soft before inserting it onto the drive motor. (Refer to
Section 2 Assembling on Page 6)
2. During daily use, in case the cleaning roller becomes dry, soak the cleaning roller till soft.
Insert the trash container
Place the lower body in an upright position, open the cleaning head cover, insert the trash container and press it
in place, then place one new disposable trash container optional and close the cleaning head cover.
Assemble the upper and lower body
Remove the quick-mount screw from the handle, then insert the handle onto the lower body of the appliance
properly. Insert the quick-mount screw and tighten it with a coin or screwdriver.
Insert the battery into the battery compartment on the lower body and tighten the screw with a coin or screwdriver.
Assembling
Quick Start Guide
MAX
45°
Lock
2
Assemble the charging base
Ready for use
Fill the clean water tank Unlock the product
Insert the clean water tank Enjoy your cleaning Empty the dirty water tank
Take out the dirty
water tank
Throw away the
used disposable
trash container
Connect the two components of the charging base.
Connect the power adapter, and the excess power line can be stored in the cable slot.
To ensure effective cleaning, make sure that the hard waste to be
collected is in front of the cleaning head.
Maintenance & Cleaning
Maximise your Hizero's cleaning power by maintaining the product regularly. See Section 5
Maintenance&Cleaning on page 10 for more instructions and tips.
Check whether it is necessary to charge the product rst (blue battery indicator means a full battery)
before use. The charging time is a maximum of 4 hours.
Use Guidance
Use Guidance
MAX
40℃
Unlock
4 Hours
3
Handle
Display Panel
Upper Body
Lower Body
Decorative Light
Cleaning Head
Trash Container
Brush Roller
Lateral Button of Cleaning Roller
Cleaning Roller
Release Button for the
Cleaning Head Cover
Body
Li-ion Battery
Clean Water Tank
Dirty Water Tank
Cap of the clean water tank
Product Label
Power Contactor
Locating Stud
Charging Base
Hand Lifting Position
Charging Contactor
Latch Locator
Spindle
Release Button for
the Clean Water Tank
Cap of the dirty water
tank (With Sensor)
Release Button for the
Dirty Water Tank
Auxiliary Wheel
Body Quick-Mount Screw
Battery Quick-Mount Screw
Product View
Battery Indicator
Mode 2 (Extra water)
Mode 1 (Normal)
Indicator for empty
clean water tank
Indicator for full dirty
water tank
Cleaning Roller Status Indicator
Brush Roller Status Indicator
Mode Button
Power Button
Lock of Cleaning Head Cover
Lateral Button of
Brush Roller
Release button for the
Cleaning Head Cover
Filter Assembly
4
Charging
In Use
Flashing Red: The product is charging.
Flashing Blue: Something is wrong and contact the Customer Service Centre for a
solution.
Solid Blue: The product is charged fully.
Flashing red: Too low battery to continue working.
Solid red: Low battery and the product will automatically power off within 3 minutes.
Solid blue: Sufficient power.
Mode 2: Extra mode, the appliance will use more water. A full tank (500ml) of clean water can be used for approximately 5
minutes (half the time)
Mode 1: Normal mode, the appliance will use less water. A full tank (500ml) of clean water can be used for approximately 10
minutes (should be used for regular clean)
Flashing: The water in the clean water tank is insufficient. The product will stop working and automatically switch-off
after 30 seconds.
Solid red: Something is wrong and contact the Customer Service Centre for a solution.
Flashing: A. The dirty water tank is full.
B. The sensor on the cap of the dirty water tank is dirty.
Solid red: A. The dirty water tank may not be inserted properly.
B. Something is wrong and contact the Customer Service Center for a solution.
Flashing: Maybe the cleaning roller is jammed by foreign object.
Solid red: Replace the cleaning roller with a new one roller has reached end of life,to reset press the mode button till the
indicator goes out.
Flashing: The cleaning head cover is not closed properly.
Solid red: A. Maybe the brush roller is jammed by foreign object
objects. B. Something is wrong and contact the Customer Service Center for a solution.
Solid blue: All is normal
Solid red: Something is wrong and check the display panel for more information.
(Extra water)
(Regular)
5
Table of Contents
1 Introduction
1.1 Safety Instructions
1.2 Technical and Security Specications
1.3 Self-Protection System
1.4 Intended Use
1.5 Floor Maintenance
3 Preparation
3.1 Charging
3.2 Remove Large Objects Off the Floor 3.3
Filling the Clean Water Tank
3.4 Locking the Body
4 Operation
4.1 Unlock the Body
4.2 Start Cleaning
4.3 Indicator for A Full/Empty Water Tank
4.4 Empty the Dirty Water Tank
4.5 Empty the Trash Container
4.6 Self-Protection System
5 Maintenance & Cleaning
5.1 Maintenance
5.2 Clean the Water Tanks
5.3 Clean the Brush Roller
5.4 Clean the Cleaning Roller
5.5 Clean the Trash Container
5.6 Clean the Cleaning Head Cover
5.7 Clean the Water Sink Drain
5.8 Clean/Replace the Filter Assembly
6 Storing & Moving
6.1 Storing
6.2 Moving
7 Replacing
7.1 Replace the Brush Roller
7.2 Replace the Cleaning Roller
2 Assembling
5
5
6
6
6
6
7
7
8
8
8
8
8
9
9
9
9
10
10
10
10
10
10
11
11
11
12
12
12
12
12
12
13
6
8 Ordering Accessories
9 Caring for the Environment
10 Warranty & After-sales
11 Troubleshooting
13
13
13
14
1 Introduction
Thank you for choosing HIZERO 4-in-1 Bionic Mop!
HIZERO 4-in-1 Bionic Mop is an intelligent oor cleaning
machine based on innovative bionic technologies, which
perfectly integrates the functions of sweeping, mopping, drying
and cleaning roller's self-cleaning. Its advent is honored as “The
second revolution in the oor cleaning eld”. The product has
a built-in rechargeable battery and when cleaning the floor, the
cleaning roller while can separate the solid trash from the liquid
one, simultaneously,self-cleaning the roller. After use, all that
needed is to discard the disposable trash container and empty
the dirty water tank. It is featured by extremely high cleaning
efficiency, simple operation and easy maintenance.
In this user manual, you will learn some tips to make the cleaning
job as easy and efficient as possible.
Please read this user manual carefully before you use the
product and save it for further reference.
1.1 Safety Instructions
1.1.1 Danger
•To prevent electric shock, never move the product over
floor/wall/plugged power cords.
• Keep all parts of the human body or large objects such as
clothes away from the cleaning roller.
1.1.2 Caution
• The product must be removed from the charging base
before cleaning or maintaining.
• Always switch off the product before you remove water
tanks or open the cleaning head cover.
• To avoid any hazard, do not let the product clean
sharp objects.
• To avoid any damage, never immerse the body of the
product in water or any other liquid, nor rinse it
under the tap.
• Never use the product to clean ammable or combustible
liquid and do not put ammable or combustible liquids in the
clean/dirty water tank.
•
•
•
Regularly check the product and all parts, stop using if the
product or the charging base is damaged, and bring it to an
authorized service center.
This product is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction to use the product by a
person responsible for their safety.
Children should be supervised to ensure that they do not play
with the product.
• Never store the product at a temperature lower than 0°C/32°F.
6
• Use only clean water or clean water with HIZERO cleaning
solution in theclean water tank of the product.
•Do not put acetic acid (vinegar) or unauthorized detergent in
the water tanks nor use the product to clean them.
• Do not put wax, oil or floor maintenance products that cannot
be diluted in the clean water tank, or use the appliance to clean
them.
• The model of the battery pack is F8Z-BTA01/F8Z-BTA02/F8Z-
BTA03.
•Only change the product on original Hizero charging base.
• Never use the battery for other purposes other than this
product, and never expose it to heat (50°C/122°F+), outdoor or
wet conditions.
•When removing or replacing the battery, keep the terminals
away from other metal objects like nail clips, keys, bails, screws,
etc. to avoid any thermal effect, smoke, fire or even explosion.
• Stop using the battery in case of leakage and call the Customer
Service Center for special battery treatment immediately.
•Do not disassemble the battery without authorization in case of
any abnormal situaton.
•Do not discard used batteries at will as special battery
treatment or recycling shall be required.
• Use only HIZERO authorized cleaning solution to prevent any
damage to internal components.
•Never clean the cleaning roller with a sharp object, or the roller
may be damaged while the cleaning performance may be
reduced.
•When there is water in the water tanks, never put the product
on its side or upside down in order to prevent any leakage.
• Clean the dirty water tank after every use to prevent the
bacteria breeding or odour.
•Do not clean the cleaning roller, brush roller or water tanks in a
dishwasher or washing machine.
• This product is intended for the indoor use only.
1.2 Technical and Security Specications
This product complies with the current recognized electrical
product technical specications and safety regulations.It is
safe to use the product if the user operates according to the
instructions of this user manual.
1.3 Self-Protection System
The product is equipped with an active protection system, and
it will stop working and alert automatically if large objects like a
towel or a patch of a curtain are rolled and stuck.
1.4 Intended Use
The product is used for water-proof
hard oors (tile, marble, wooden, etc.)
only. Do not use this product to clean
carpets or other oors that are water-
sensitive.
Note: Do not use the product for carpet.
1.5 Floor Maintenance
Follow the cleaning and maintaining instructions of the user
manual, and simultaneously refer to the maintenance description
of your oors.
HIZERO cleaning solution can be used to advance the cleaning
performance. Do not add any unauthorized oor-care product
into the water tank.
??
2 To open the cleaning head, press the "PRESS" button on
the cleaning head cover to open the cover, then take out the
trash container.
3 Close the cleaning head cover, put the lower body on its side
on at ground and make sure the lateral button of the cleaning
roller is on the upside.
2 Assembling
1 Open the package and take out the cleaning roller. Before
installation, please immerse the whole cleaning roller in clean
water (recommend 15°C-40°C), and evenly squeeze the entire
body of the cleaning roller until the body is completely soft.
Then, take out the soft cleaning roller and squeeze the excess
water out to prepare for the following installation.
1
2
3
7
Note: If the appliance fails to start after the
connection, please try again to insert the handle
onto the lower body and restart the appliance.
4 Insert the cleaning roller onto the drive motor (note: the
maximum open angle of the drive motor is 45°), gently push and
x it into the cleaning head till the lateral button is in place.
8 Insert the quick-mount screw into the bolt hole on the
handle of the appliance and tighten it.
9 Insert the battery into the battery compartment on the lower
body, tighten the screw with a coin or screwdriver and make sure
the battery is installed well.
10 Assemble the two parts of the charging base . Connect the
power adapter and put the excess power line in the special cable
slot.
5 Place the lower body in upright position, open the cleaning
head cover, insert the trash container and press it into place,
then place a new disposable trash container optional. Close
the cover until you hear a click to ensure the cover is closed
well.
6 Push the lower body forward lightly until you hear a
click which means the product is locked in a right position.
7 Take out the handle and remove the body quick-mount
screw first. Then gently insert the handle onto the lower body
and make sure the handle and the lower body of the appliance
are connected closely.
12
3 Preparation
3.1 Charging
1 Make sure the charging base and power adapter are
connected well and plug the adapter in a properly grounded
outlet.
2 Place the product on the charging base and clasp the
latch locator onto the locating stud. The battery indicator will
flash red to indicate the product is charging.
1
23
4
12
3 4
12
1
2
1 2 3
4
3 4
8
3 Before first use, please check if it needs charge, and if
needed, charge the product to full power (it needs a maximum of
4 hours to a full charge).
3 Turn the cap clockwise to tighten it and install back the clean
water tank into the product and make sure it is installed well.To
prevent the product from toppling over, hold it upright with one
hand and place the clean water tank with your other hand.
12
Note: For your safety, please keep the charging base in a dry
situation and do not touch the charge port. Note: To avoid the water tank from sliding out during
cleaning, please make sure it is locked.
Note: If detergent is needed, only HIZERO cleaning solution is
allowed. And adding the cleaning solvent/tablet must follow the
related use instruction before lling in clean water.
Note: During locking or unlocking, the click sound is normal.
Hold the handle of the product, push it forward lightly until you
hear a click which means the product is locked well.Do not push
it any further, or it will damage the product.
Fill the clean water tank before every use.
3.2 Remove Large Objects Off the Floor
Before using the product, remove large objects such as toys,
power cords and shoes.
3.4 Locking the Body
3.3 Filling the Clean Water Tank
1 Press the release button while pulling the clean water tank
to take it out. To prevent the product from toppling over, hold it
upright with one hand and take out the clean water tank with
your other hand.
2 Turn the cap anticlockwise and remove it from the clean
water tank. Fill the clean water tank with cold or warm water
(should not be higher than 40°C/104°F). If needed, HIZERO
cleaning solution may be added (refer to Section 1.5 Floor
Maintenance).
12
12
4 Operation
Lift up the product from the charging base, hold the handle and
x the cleaning head with one foot, then slowly pull back the
body until you hear a click which means the body is unlocked.
Press the power button to start the product.
4.1 Unlock the Body
12
LOCK
12
9
Note: To avoid the water tank from sliding out during cleaning,
make sure it is placed and locked well. To avoid any bad
connection, make sure to wipe the metal sensor plate with a
soft and dry cloth.
4.3 Indicator for A Full/Empty Water Tank
4.4 Empty the Dirty Water Tank
4.2 Start Cleaning
1 Make sure that the hard waste to be collected is always in
front of the cleaning head, or it may not be cleaned effectively.
1 Press the release button for the dirty water tank to take it
out. To prevent the product from toppling over, hold it upright
with one hand and take out the dirty water tank with your other
hand.
2 To easily remove the cap of the dirty water tank, hold the
cap and pull it up lightly from the front to the back as the below
picture shows. Then slowly pour out the dirty water and be
careful of dirty water overow as well as spilling.
3 Rinse the empty dirty water tank and its cap under the tap
and and wipe the metal sensor plate with a soft and dry cloth.
Then place the tank back into the product. To prevent the
product from toppling over, hold it upright with one hand and put
the dirty water tank with your other hand.
2 To avoid inefcient cleaning, the cleaning path shown in the
following pictures is recommended.
3 To remove stubborn stains, move the product back and forth
repeatedly.
4 Do not lay the product as
the picture shows.
5 If the cleaning roller is stuck by foreign objects, press
the power button to switch off the product immediately.
1 The indicator will ash when
the clean water tank is empty. At
this time, switch off the product
and ll the clean water tank ( refer
to Section 3.3 Filling the Clean
Water Tank). Then re-start the
product.
2 The indicator will ash and the
product will stop working when the
dirty water tank is full. Empty the
dirty water tank (refer to Section
4.4 Empty the Dirty Water Tank
) and re-start the product.
12
10
2 If a disposable trash container was not used, take out the
trash container and use the cleaning brush to sweep the trash
into a dustbin.
a disposable trash container
is used
a disposable trash container is
not used
5.2 Clean the Water Tanks
We strongly advise you to empty the tanks before storing the
product.
To disassemble and assemble the clean water tank, refer to
Section 3.3 Filling the Clean Water Tank . To disassemble and
assemble the dirty water tank, refer to Section 4.4 Empty the
Dirty Water Tank.
The cap of the clean/dirty water tank can be rinsed under the
tap.
Note: The product must be removed from the charging
base and switched off before cleaning or maintaining.
4.6 Self-Protection System
The self-protection system has been designed to identify
abnormal conditions. When the system is activated, the product
will stop operating immediately to prevent damage to the object
and product.
To continue cleaning, follow the instructions below!
4.6.1 Self-Protection of the Cleaning/Brush Roller
The indicator for the cleaning/brush roller on the display panel
will ash if the cleaning/brush roller goes wrong.
1 Open the cleaning head cover and remove the jammed
object.
2 If the jammed object is not easy to find, disassemble the
brush roller to have a better look.
3 After clearing the obstruction, reinstall the cleaning/brush
roller and re-start the product. To disassemble and assemble
the cleaning/brush roller, refer to Section 7 Replacing .
5 Maintenance & Cleaning
5.1 Maintenance
1 Regularly clean the shell of the product with a soft damp
cloth. Do not use abrasive cleaning tools like wire balls as well
as corrosive detergents to clean the shell in case of scratches
or damage.
2 To avoid any damage, do not immerse the body in water or
any other liquid, nor rinse it under the tap.
4 Regularly check the power adapter to ensure the power
cable is intact and safe to use.
3 Regularly check the cleaning roller and brush roller.
Note: Clean the dirty water tank after each use to prevent
bacteria.
5.4 Clean the Cleaning Roller
Method 1: Make the cleaning roller do self-cleaning.
1 Fill up the clean water tank ( add some HIZERO original
cleaning solution) and install it back, empty the dirty water tank
and install it back, lock the product in an upright position and put
it on the charging base properly, then unplug the power adapter.
2 Start the product and switch to Mode 2. Let the product run
by itself until the clean water tank is empty.
5.3 Clean the Brush Roller
1 To disassemble and assemble the brush roller, refer to
Section 7.1 Replace the Brush Roller.
2 Cut tangled items such as hairs from the brush roller.
3 Clean the brush roller with clean water (mixing with
some cleaning solution is recommended) and let it dry
before reinstalling it.
12
4.5 Empty the Trash Container
1 Open the cleaning head cover, remove the disposable trash
container. And if needed, put a new disposable trash container
for the next use.
11
3 As per the following images, in addition to doing self-cleaning
on the power-off charging base, the product can also do self-
cleaning as long as its lifted off the floor (keep the product in an
upright position), but both conditions need to be under Mode 2.
4 To achieve a better cleaning effect, multiple self-cleaning is
recommended.with HIZERO detergent.
Note: Keep the product upright when the cleaning roller is self-
cleaning.
Note: Empty the dirty water tank before the aforementioned steps.
Method 2: Manual cleaning
1 Refer to Section 7.2 Replace the Cleaning Roller
to disassemble the cleaning roller and gently wash it by hand
under the tap.
12
5.5 Clean the Trash Container
5.6 Clean the Cleaning Head Cover
1 Take out the trash container, then empty and wash it under
the tap. The cleaning brush can be used to sweep off the trash.
Let it dry before reassembling.
5.7 Clean the Water Sink Drain
1 Open the cleaning head cover, take out the trash container
and lter assembly, then turn the cleaning head over and take
out the cleaning roller.
2 Find the removable water sink drain in the groove of the
bottom shell, then use the tip of the cleaning brush to gently
push the sink through the hole in the nozzle to take the sink
out.
3 Clean the water sink drain with clean water, and if
necessary, add some mild cleaning solvent.
1 Open the cleaning head cover, press the release button to
take it apart from the main body, then remove the brush roller
attached on the cover.
2 Clean the cover with a soft damp cloth.clean behind the brush
roller carefully.
3 Reinstall the brush roller onto the cover, then x the cover
back to the cleaning head.
12
1 2
2
23
1
12
1 Switch off the product and lock it in an upright position.
2 Open the cleaning head cover, press the square button at
the lateral side to take out the brush roller (Maximum open angle
of the drive motor is 30°. Please use appropriate strength and
method to avoid any damage).
If you want to continue to benet from the best cleaning results,
make sure you always use the original HIZERO brush roller, and
we recommend you to replace it every six months.
4 Install the water sink drain back correctly, make sure the
positioning holes on the water sink match rightly with the main
body, then slightly press the water sink from left to right to check
if it is fixed well, and lastly make both ends of the water sink
flush.
5 Finish the rest of the installation steps.
5.8 Clean/Replace the Filter Assembly
1 Take out the lter assembly.
1 Before storing, switch off the product, lock the body and
place it onto the charging base.
2 Please clean the inside of the cleaning head before storing
to avoid bacteria breeding.
3 Before storing, make sure the water tanks are empty.
4 If the product will be out of service for above one week, cut
off the power, take out the cleaning roller to dry it and then store
the product.
2 Clean/Replace the lter assembly.
3 Put back the lter assembly.
Note: Recommend to replace the lter assembly every 3 months.
Note: If there is sand or other sharp objects on the oor, do not
operate the product to avoid any possible scratch.
6 Storing & Moving
7 Replacing
6.1 Storing
7.1 Replace the Brush Roller
6.2 Moving
1 Make sure the product is switched off and locked in upright
position.
2 To move the product, use the hand lifting position on the
body's back, or tilt the product backwards to use the back
wheels.
2
23
1
13
1 Switch off the product and take out the trash container, then
empty or take out the water tanks.
2 Put the product on its side on at ground and let the side
which has the square button upwards. Press the lateral square
button to take the cleaning roller out.
3 Insert a new cleaning roller onto the drive motor, push and
x it into the cleaning head till the lateral button is in place.
To insert a new cleaning roller, refer to Section 2 Assembling.
3 Insert a new brush roller onto the drive motor, push and x it
into the cleaning head till the lateral button is in place.
If you want to continue to benet from the best cleaning results,
make sure you always use original HIZERO cleaning roller, and
replace it every four months.
To purchase accessories for the product, please visit our website
www.hizero.com, or contact HIZERO Customer Service Centre
in your country/region.
When the product reaches its service life, it is highly advised for
you to take the product to the governmental recycle station to
contribute to the environment preservation.
For the detailed information of warranty and after-sales service,
please visit our website: www.hizero.com or contact HIZERO
Customer Service Centre in your country/region.
Your 4-in-1 Bionic Mop has been designed and developed
with the greatest possible care. In the unfortunate case that
the product needs repair, the Customer Service Centre in your
country/region will help you by arranging any necessary repairs
in the shortest possible time and with maximum convenience.
Note: The maximum open angle of the drive motor is 30°. Please
operate carefully.
Note:
1. The Maximum open angle of the drive motor is 45°,
please operate carefully.
2. The used cleaning/brush roller is classified as plastic
waste, so please take proper care according to your local
environmental protection regulations.
7.2 Replace the Cleaning Roller
8 Ordering Accessories
9 Caring for the Environment
10 Warranty & After-sales
Hizero Technologies Co., Ltd. will not be liable for any
damage resulting from improper use or disassembly
by customers.
67
2
34
1
56
A
B
C
D
14
11 Troubleshooting
This chapter summarizes the most common problems you could encounter with the product. If you are unable to solve the problem with
the information below, please contact the Customer Service Centre in your country/region or visit our FAQ page on www.hizero.com.
Problem
The cleaning roller status indicator
keeps lit, but the product works
normally.
The appliance leaks water
The product fails to start.
The brush roller status
indicator flashes red.
The Brush roller status
indicator is solid red.
The indicator for full dirty water
tank ashes in red while there is no
liquid in it.
Product failsto start for the self-
cleaning roller though the product
is on the charging base.
There is foam left in the trash
container.
Possible cause
B.The upper body and the lower
body of the appliance were not
assembled properly.
The cleaning roller has reached its
service life.
A. The cleaning roller is not
completely soft.
B. The cleaning roller deforms or is
installed incorrectly.
C. The lter assembly is clogged.
A.The battery power has run out.
C.The battery wasn't inserted
properly.
The cleaning head cover isn't
completely closed.
The brush roller is jammed
by something foreign.
The dirty water sensor on the
cap of the dirty water tank is
covered by some dirt.
The charging base is not
disconnected from power.
Some detergent other than
HIZERO original cleaning
solution was been used.
Solution
Reassemble the upper body and the lower body of
the appliance.
Please replace it with a new cleaning roller,
then long press the mode button until the indicator
goes out.
If a new cleaning roller is not available temporarily,
please directly long press the mode button until the
indicator goes out.
Refer to Section 2 Assembling for the instruction
about soaking and softening the cleaning roller.
Notice that squeeze excess water before installing.
Check the cleaning roller and its lateral button on
the side to see whether there is a misplacement or
deformation. If so, reinstall or replace the cleaning
roller.
Clean or replace the lter assembly.
Charge the product and restart it.
Reinsert the battery.
Check the cleaning head cover to see whether it is
open and if so, close it well.
Disassemble the brush roller to check whether the
cleaning roller, as well as its drive motor, is
tangled by trash and if so, carefully clean with
scissors.
Open the dirty water tank and remove the cap of
it, check to see whether the dirty water sensor on
the cap is covered by dirt and if so, clear promptly.
At the same time, please regularly clean the
dirty water tank to prevent ineffective dirty water
monitor.
Unplug the power adapter since the product won't
start while charging.
HIZERO 4-in-1 bionic mop allows only HIZERO
original cleaning solution, so please do not use
any unauthorized detergent which may cause
unexpected damage to the product.
www.hizero.com
M8900000104
英文用户手册
李晓平
2019.8.15
F801
148mm×210mm
M8900000104
V011
封面 128g 铜板纸，四色印刷
内页 80g 轻型纸，专色印刷 骑马钉
装订，正反面印刷
* 注：此页面无需印刷
Other manuals for F801
2
Table of contents
Other Hizero Steam Cleaner manuals
