Silvercrest SDM 1500 C2 User manual

IAN 280641
STEAM MOP SDM 1500 C2
STEAM MOP
Operating instructions
DAMPFMOPP
Bedienungsanleitung
GŐZÖLŐS FELMOSÓ
Használati utasítás
PARNI ČISTILNIK
Navodila za uporabo PARNÍ MOP
Návod k obsluze
PARNÝ MOP
Návod na obsluhu

GB Operating instructions Page 1
HU Használati utasítás Oldal 19
SI Navodila za uporabo Stran 37
CZ Návod k obsluze Strana 55
SK Návod na obsluhu Strana 73
DE/AT/CH Bedienungsanleitung Seite 91
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik
funkcióját.
Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.

C
AB

GB │ 1 ■
SDM 1500 C2
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Information concerning these operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . 2
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Intended use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Operating components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Unpacking and installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Package contents and transport inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Disposal of packaging materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Assembling the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Handling and operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Filling with water. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
After use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Maintenance/changing the filter . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Kompernass Handels GmbH warranty . . . . . . . . . . . . . . . . . . . . . . .15
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Importer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Ordering spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

■ 2 │ GB SDM 1500 C2
Introduction
Information concerning these operating instructions
Congratulations on the purchase of your new appliance.
You have selected a high-quality product. The operating instructions are part of
this product. They contain important information on safety, usage and disposal.
Before using the product, familiarise yourself with all operating and safety instructions.
Use the product only as described and for the specified areas of application.
Please also pass on these operating instructions to any future owner.
Copyright
This documentation is protected by copyright.
Any copying or reproduction, including in the form of extracts, or any reproduction
of images (even in a modified state), is permitted only with the written authorisation
of the manufacturer.
Intended use
This appliance is intended exclusively for cleaning indoor floors. The appliance is
not intended for any other purpose, nor for use beyond the scope described. The
appliance is not intended for use in commercial or industrial environments.
The manufacturer accepts no responsibility for damage caused by failure to observe
these instructions, improper use or repairs, unauthorised modifications or the use
of unapproved replacement parts. The operator bears sole liability.

GB │ 3 ■
SDM 1500 C2
Safety instructions
RISK OF ELECTRIC SHOCK!
► Connect the appliance only to mains power sockets supplying
a mains power voltage of 220 - 240 V ~, 50/60 Hz.
► In the event of operating malfunctions, and before cleaning
the appliance, disconnect the plug from the mains power
socket.
► To disconnect the power cable, always pull the plug from the
socket, do not pull the power cable itself.
► Do not kink or crush the power cable, and route the cable
so that it cannot be stepped on or tripped over.
► To avoid risks, arrange for defective plugs and/or power
cables to be replaced at once by qualified technicians or
our Customer Service Department.
► Make sure that the power cable does not become wet or
damp during use. Route the cable in such a way that it
cannot be crushed or damaged.
► To prevent risks, stop using the appliance immediately if it
is damaged.
► Disconnect the appliance from the mains power socket before
filling it with water, changing accessories or cleaning it.
Use the appliance only in dry indoor areas, not
outdoors.
► Never submerse the appliance in water or other liquids!
► Never aim the steam jet directly at electrical appliances or
equipment which contains electrical components, such as
the interior of ovens.

■ 4 │ GB SDM 1500 C2
RISK OF ELECTRIC SHOCK!
► Operate the appliance only with dry hands and never without
shoes (i.e. not barefoot). This will help reduce the effect of
an electric shock in the event of a malfunction.
► Never aim the appliance at moisture-sensitive objects.
► This appliance may be used by persons with limited physical,
sensory or mental capabilities or lack of experience and
knowledge, provided that they are under supervision or have
been told how to use the appliance safely and are aware of
the potential risks. Children must not use the appliance as a
plaything. Cleaning and user maintenance tasks may not be
carried out by children unless they are supervised.
WARNING! RISK OF INJURY!
► Some parts of the appliance may become hot during use!
There is a risk of scalding!
► Allow the accessories used to cool down before dismantling
them.
► Use only the original accessory parts for this appliance.
Other accessories may not meet the safety requirements.
► The appliance may not be used if it has been dropped, if there
are any obvious signs of physical damage or if it is leaking.
► The appliance must be kept out of the reach of children if it
is switched on or is cooling down.
► Never direct the steam at people or animals. Hot steam can
cause serious injuries!
► Always pull the plug out of the power socket during each
break in use, as well as after use and before any cleaning.

GB │ 5 ■
SDM 1500 C2
RISK OF BURNS!
Caution! Hot surface!
This symbol warns you about escaping steam.
Please follow the safety instructions!
CAUTION! MATERIAL DAMAGE!
► Use the appliance only on floors made of marble, stone, tile,
parquet flooring or hardwood that have been treated and
are impervious to water.
► Never use the appliance ...
–... on untreated or permeable floors,
–... on glass surfaces,
–... on soft plastic surfaces,
–... on floors that have been treated with wax,
–... on carpets with wool content.
► Always comply with the cleaning instructions of the carpet
manufacturer. Before cleaning, check also whether the car-
pet is suitable for steam cleaning. Use the appliance only
on parquet floors if they have been hard-sealed.
► Do not leave the appliance standing on wooden floors for
any length of time while it is switched on. This might cause
the wood to swell.
► Do not operate the appliance with an empty water tank.
Otherwise, the pump could run dry and overheat.
► Do not use an external timer switch or a separate remote
control system to operate the appliance.
► Never leave the appliance unattended during operation.
► Do not use the appliance outdoors.

■ 6 │ GB SDM 1500 C2
CAUTION! MATERIAL DAMAGE!
► Ensure that the appliance, the power cable and the plug do
not come into contact with heat sources such as hotplates or
naked flames.
Operating components
Figure A:
1“Handle” release button
2Carrying handle
3Main unit
4Connection nozzle
5Steam foot
6Pad
7Filter
8Water tank
9“Water tank” release button
0POWER control lamp
qRed control lamp “high steam level”
wGreen control lamp “low steam level”
eMODE button
r“Steam” button
Figure B:
tNotch
zUpper cable hook
uOn/off switch
iLower cable hook
Figure C:
oReplacement pad
pCarpet ring
aCarpet ring release aid

GB │ 7 ■
SDM 1500 C2
Unpacking and installation
Safety instructions
WARNING
During the first use of the appliance there is a risk
of injury and/or damage to property!
To avoid risks, observe the following safety instructions:
► Do not allow children to play with packaging materials.
There is a risk of suffocation.
Package contents and transport inspection
The appliance is supplied with the following components as standard (see fold-
out page):
● Main unit
● Steam foot
● Carpet cleaning ring
● 2 pads
● Operating instructions
NOTE
► Check the package for completeness and for signs of visible damage.
► If the delivery is incomplete or damage has occurred as a result of defec-
tive packaging or during transport, contact the service hotline (see section
Service).
Unpacking
♦ Remove all parts of the appliance and the operating instructions from the box.
♦ Remove all packaging materials and any films and labels.

■ 8 │ GB SDM 1500 C2
Disposal of packaging materials
The packaging protects the appliance from damage during transport. The packaging
materials have been selected for their environmental friendliness and ease of
disposal, and are therefore recyclable.
Returning the packaging into the material cycle conserves raw materials and
reduces the amount of waste generated. Dispose of packaging materials that
are no longer needed in accordance with applicable local regulations.
NOTE
► If possible, keep the appliance's original packaging during the warranty
period so that the appliance can be packed properly for return shipment
in the event of a warranty claim.
Assembling the appliance
♦ Push the main unit 3onto the connection nozzle 4on the steam foot 5and
press the main unit 3down until the round catch clicks into place.
♦ Attach a pad 6from below onto the steam foot 5.
NOTE
► If you intend to clean carpeting with the steam mop, fit the steam foot 5
onto the carpet ring p. Ensure that the carpet ring unlocking aid ais in
line with the connection nozzle 4. Push the steam foot 5onto the carpet
ring pso that it clicks audibly into place. This will allow the pad 6to
glide over the carpet.
► To remove the carpet ring p, press your foot onto the carpet ring release
aid aand pull the steam foot 5carefully off the carpet ring p.
Handling and operation
This section provides you with important information on handling and using the
appliance.
Filling with water
CAUTION – PROPERTY DAMAGE!
► Never operate the appliance without water in the water tank 8!
The pump could overheat and be damaged!
1) Push the “Water tank” release button 9downwards and simultaneously
pull the water tank 8towards the rear and off the appliance with a tilt
movement.
2) Turn the water tank 8and unscrew the cap.
3) Fill the water tank 8with tap water up to the MAX mark.

GB │ 9 ■
SDM 1500 C2
NOTE
If the mains water in your location is rated as hard, it is recommended that
you mix the mains water with some distilled water. Otherwise, the jets for
the steam blast function could calcify (become blocked) prematurely.
To extend the optimal steam blast function, mix mains water with
distilled water according to the table:
Water hardness Ratio of distilled
water to
tap water
very soft/soft 0
medium 1:1
hard 2:1
very hard 3:1
The water hardness level can be queried at your local water works.
4) Attach and hand-tighten the clamp.
5) Turn the water tank 8around again and place it back onto the main unit 3:
First fit the lower part into the main unit 3and then flip the top part into the
device. Push it firmly into place so that the water tank 8audibly clicks into
place and sits firmly on the main unit 3.
Operation
CAUTION – PROPERTY DAMAGE!
► If you are not sure whether the floor is suitable for cleaning, please carry
out a tolerance test using a concealed part of the floor.
► Always comply with the cleaning instructions of the carpet manufacturer.
Before cleaning, check also whether the carpet is suitable for steam clean-
ing.
► Never use the appliance without a pad 6on the steam foot 5.
Otherwise the floor could get scratched!
► Never operate the appliance without water in the water tank 8!
The pump could overheat and be damaged!
NOTE
► Before you clean the floor with the steam mop, we recommend that you
vacuum the floor to remove any loose particles of dirt.
Once the appliance is assembled and filled with water:
1) Press and hold in the “Handle” release button 1and flip the handle up-
wards so that it clicks into place.

■ 10 │ GB SDM 1500 C2
2) If not already done: Completely unwind the power cable from the cable
hooks z/i. To facilitate the unwinding of the cable, you can flip down the
upper cable hook zby pulling it out a little and turning it at the same time.
3) Run the cable through the notch ton the rear of the handle so that the
cable does not hang down into the working area.
4) Insert the plug into the mains power socket.
5) Set the on/off switch uto “I”. The on/off switch ulights up, the red
POWER control lamp 0flashes.
6) Use the MODE button eto select the desired level of steam generation:
–Press 1 x: low steam level, green control lamp wlights up.
–Press 2 x: high steam level, red control lamp qlights up.
–Press 3 x: no steam, standby, POWER control lamp 0lights up.
NOTE
► We recommend the high steam level especially for moisture- and heat-
resistant floor coverings, such as tiles.
► We recommend the low steam level especially for moisture- and heat-
sensitive floor coverings, such as parquet flooring.
7) Wait around 30 seconds while the appliance heats up.
8) Press the “Steam” button r. The appliance starts generating steam and,
after a short time, steam is emitted through the pad 6.
9) Wipe over the desired area.
If the water tank 8becomes empty during use:
NOTE
► Once the water tank 8has been pumped empty, the pump will continue
running a little while until the empty water tank 8is indicated by the simul-
taneous flashing of the red control lamp “high steam level” q, the green
control lamp “low steam level” wand POWER control lamp 0.
–Press the “Steam” button r again to stop steam production.
–Set the on/off switch uto “O”.
–Remove the water tank 8, fill it and replace the water tank 8as
described in the section “Filling with water”.
–Set the on/off switch uto “I”.
–Select the desired steam level as described above and press the
“Steam” button r.

GB │ 11 ■
SDM 1500 C2
10) When you are finished treating all of the surfaces, press the “Steam”
button rto stop steam production.
11) Set the on/off switch u to “O”. The POWER control lamp 0goes out.
12) Remove the power plug from the mains power socket.
NOTE
► If you see streaks on the floor after cleaning with the appliance, this may
be due to the previously used cleaning fluids. Simply clean the floor again
using the steam mop. The smears should now be gone.
After use
1) Allow the appliance to cool down.
2) Remove the pad 6.
3) Remove the water tank 8from the appliance and empty it.
4) Pull the upper cable hook zout a little and turn it back upwards.
Wind the cable back around the two cable hooks z/i.
Fix the end of the power cable using the cable clip located on the cable.
Cleaning and care
RISK OF ELECTRIC SHOCK!
► Always remove the mains power plug before cleaning the appliance!
WARNING – RISK OF INJURY!
► Allow the appliance to cool down before cleaning it. Risk of burns!
CAUTION – PROPERTY DAMAGE
► When cleaning the surfaces use neither abrasive or chemical cleaners,
nor sharp or scratchy objects.
■ Empty the water tank 8after every use.
■ After each use, remove the pad 6from the steam foot 5and wash it out.

■ 12 │ GB SDM 1500 C2
■ Note the following washing instructions when you wash the pad 6in the
washing machine:
Wash at max. 60°C
Do not tumble dry
Do not iron
■ If necessary, wipe the appliance with a damp cloth. For stubborn soiling use
a mild detergent on the cloth.
Maintenance/changing the filter
After 4–6 months or approximately 100 cleaning cycles (one cycle corresponds
to one water tank filling), you will need to change the filter 7. Please contact
our Service Department for replacement filters.
RISK OF ELECTRIC SHOCK!
► Before changing the filter 7, always pull out the mains plug!
1) To remove the filter 7, first remove the water tank 8from the appliance.
2) Pull the filter 7upwards out of the appliance.
3) Insert the new filter 7.
4) Replace the water tank 8.

GB │ 13 ■
SDM 1500 C2
Troubleshooting
Programme Possible causes Possible solutions
The appliance is
not working. The plug is not connected. Connect the appliance to a
mains power socket.
The appliance
produces no steam.
The "Steam" button rhas
not been pressed. Press the "Steam" button r.
There is no water in the
water tank 8.Fill the water tank 8with
tap water.
The filter 7is blocked. Change the filter 7.
No steam setting has
been selected. Use the MODE button eto
select the desired level of steam.
The pump makes
unusually loud
noises.
There is no water in the
water tank 8.Fill the water tank 8with
tap water.
A whitish edge
forms on the floor
when the appliance
stops briefly during
operation.
Lime has collected.
Wipe the limescale away with a
damp cloth. If necessary, add a
little descaler onto the cloth.

■ 14 │ GB SDM 1500 C2
Storage
■ Fold the handle by pressing the “Handle” release button 1.
■ Pull the upper cable hook zout a little and turn it back upwards.
Wind the cable back around the two cable hooks z/i.
■ Carry the appliance using the carrying handle 2.
■ Store the appliance in a dry and dust-free location.
Disposal
Do not dispose of the appliance in your normal domestic waste.
This product is subject to the provisions of European Directive
2012/19/EU-WEEE (Waste Electrical and Electronic Equipment).
Dispose of the appliance via an approved waste disposal company or your
municipal waste disposal facility. Please comply with all applicable regulations.
Please contact your waste disposal facility if you are in any doubt.
Appendix
Technical data
Voltage supply 220 - 240 V ~(AC) | 50 / 60 Hz
Power consumption 1370 - 1630 W
Protection rating
IPX4
Protected against water splashes
from any direction.
Information on the pads 6/o
Material composition 100% polyester
Wash at max. 60°C
Do not tumble dry
Do not iron

GB │ 15 ■
SDM 1500 C2
Kompernass Handels GmbH warranty
Dear Customer,
This appliance has a 3-year warranty valid from the date of purchase. If this product
has any faults, you, the buyer, have certain statutory rights. Your statutory rights
are not restricted in any way by the warranty described below.
Warranty conditions
The validity period of the warranty starts from the date of purchase. Please keep
your original receipt in a safe place. This document will be required as proof of
purchase.
If any material or production fault occurs within three years of the date of purchase
of the product, we will either repair or replace the product for you at our discretion.
This warranty service is dependent on you presenting the defective appliance
and the proof of purchase (receipt) and a short written description of the fault
and its time of occurrence.
If the defect is covered by the warranty, your product will either be repaired or
replaced by us. The repair or replacement of a product does not signify the begin-
ning of a new warranty period.
Warranty period and statutory claims for defects
The warranty period is not prolonged by repairs effected under the warranty.
This also applies to replaced and repaired components. Any damage and defects
present at the time of purchase must be reported immediately after unpacking.
Repairs carried out after expiry of the warranty period shall be subject to a fee.
Scope of the warranty
This appliance has been manufactured in accordance with strict quality guidelines
and inspected meticulously prior to delivery.
The warranty covers material faults or production faults. The warranty does not
extend to product parts subject to normal wear and tear or fragile parts such as
switches, batteries, baking moulds or parts made of glass.
The warranty does not apply if the product has been damaged, improperly used
or improperly maintained. The directions in the operating instructions for the product
regarding proper use of the product are to be strictly followed. Uses and actions
that are discouraged in the operating instructions or which are warned against
must be avoided.
This product is intended solely for private use and not for commercial purposes.
The warranty shall be deemed void in cases of misuse or improper handling, use
of force and modifications/repairs which have not been carried out by one of
our authorised Service centres.

■ 16 │ GB SDM 1500 C2
Warranty claim procedure
To ensure quick processing of your case, please observe the following instructions:
■ Please have the till receipt and the item number (e.g. IAN 12345) available
as proof of purchase.
■ You will find the item number on the type plate, an engraving on the front
page of the instructions (bottom left), or as a sticker on the rear or bottom of
the appliance.
■ If functional or other defects occur, please contact the service department
listed either by telephone or by e-mail.
■ You can return a defective product to us free of charge to the service address
that will be provided to you. Ensure that you enclose the proof of purchase
(till receipt) and information about what the defect is and when it occurred.
You can download these instructions along with many other manuals,
product videos and software on www.lidl-service.com.
Service
Service Great Britain
Tel.: [phone] (£ 0.10/Min.)
E-Mail: [email protected]
IAN 280641
Importer
Please note that the following address is not the service address. Please use the
service address provided in the operating instructions.
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com

GB │ 17 ■
SDM 1500 C2
Ordering spare parts
You can order the following replacement parts for product SDM 1500 C2:
► 2 x Replacement pad ► 1 x Filter
Order the replacement parts via the Service Hotline (see section „Service“) or
simply visit our website at www.kompernass.com.
NOTE
► Have the IAN number of the appliance ready (can be found on the cover
of these operating instructions) when you place your order.