HKS VIITS User manual

INSTRUCTION MANUAL
INSTRUCTION
E05253-E11020-00
September 2021
Ver. 3-1.01
Thank you for your purchase of BOOST CONTROLLER.
・ This manual indicates items that require attention in order to install this product
safely and lists precautions to avoid any possible damage and/or accidents.
・ This product was designed based on installation onto a specific factory vehicle
or a vehicle using other HKS products. The performance and/or safety cannot be
guaranteed if this product was installed onto other inapplicable vehicles.
・ Contact HKS dealer for any lost parts, replacement, and this manual.
・ HKS will not be responsible for any damage caused by incorrect installation and/or
use of this product.
・ This product works only with a vehicle with DC12V negative ground.
・ The specifications of this product are subject to be changed without notice.
・ This manual is subject to be revised without notice.
・ When removing factory parts, refer to the factory manual. The factory manual must
be purchased if you don't have it.
２. Safety Precaution
The following precautions for use of this product are to prevent possible
accidents and/or injuries and for proper use.
ー 1 ー ー ２ ー
VIITS BOOST CONTROLLER
VIITS-EL001
Boost up of turbocharged vehicle
ABARTH595 COMPETIZIONE [31214T]
Product
Code Number
Use
Application
１. Introduction
３. Product Features
１． Stop the engine of the vehicle and Disconnect the cable terminal from the
negative terminal of the battery.
２． Install the BOOST CONTROLLER main unit in an arbitrary place.
・ Avoid the following places.
- Places where the temperature becomes high like the engine body.
- Places where direct water is applied.
・ Confirm that the connection harness reaches the pressure sensor.
・ When using double sided tape, clean the surface to be pasted, paste it, and use
tie wraps together.
When pasting with double-sided tape only, it is dangerous when it peels off due
to aged deterioration.
３． Connect the BOOST CONTROLLER main unit and Connector for main unit.
４． Disconnect Manufacturer's original connector from Pressure sensor, and wire
the connection harness of BOOST CONTROLLER.
・ Longer harness is channel 1, shorter one is channel 2.
・ In factory default settings, the boost-up data in channel 1 and channel 2 are
same.
・ Please be aware of the channel order during modifying boost-up data by
Power Editor EasyWriter software.
５． Lock the connection harness of BOOST CONTROLLER with tie wrap so as
not to hinder
the running of the vehicle.
・ Places where the temperature becomes high like the engine body.
６． After confirming that all connectors are correctly connected, connect the cable
terminal to the negative terminal of the battery.
７． Turn the ignition on and check that the LED of the BOOST CONTROLLER main
unit lights up.
・ Even if the ignition is turned on, if the LED does not light up, poor contact of the
connector may be considered.
Connection harness
BOOST CONTROLLER main unit
Pressure sensor
Pressure sensor
Operation confirmation LED
Lighting off ： Power off
Lighting on ： Power on
1 blink ： ch1 data is broken
2 blinks ： ch2 data is broken
3 blinks ： ch1/ch2 data is broken
When the LED flashes the boost
will not rise, it will behave like a
normal vehicle.
Manufacturer's
original connector
５. Installation procedure
・ By connecting this product between Pressure sensor and Manufacturer's
original connector, boost can be easily raised.
・ Even after installing this product, you can return to the normal state by
connecting the "return connector" instead of the BOOST CONTROLLER main
unit.
・ You can change the data for the boost up of the main unit by connecting to the
personal computer with USB harness included in the product and using Easy Writer
for Power Editor.
Easy Writer for Power Editor is available for free on the HKS website.
２
１pc.
Connection harness
１
１pc.
BOOST CONTROLLER
３
１pc.
USB harness
４. Parts List
４
１pc.
Connector to return to normal
６
２pc.
Tie wrap (large) ７
２pc.
Double-sided tape ８
１pc.
Instruction Manual
Connector for connecting USB harness
・ Make it stuck with tie wraps or the like so that
it will not be shaken during driving
Connector for main unit
Channel 1
Channel 2
Indicates risk of serious injury and/or possible death.
Indicates risk of serious injury or property damage.
WARNING ：
CAUTION ：
● Make sure to work on the vehicle in a well-ventilated area to prevent possible
explosion or a fire.
● Make sure to hold connectors when removing them to avoid possible damage to
other electronics parts and/or a fire caused by disconnection or a short circuit.
● Stop using the product if any unusual situation is noticed. Consult the dealer
immediately. Failure to do so may cause an electric shock, burn out, or damage
to the vehicle.
● Make sure to work on the vehicle in area where a vehicle can be parked safely.
WARNING
CAUTION
● Do not install this product by yourself.
● Do not modify, disassemble, and/or remodel the product and attached parts to
avoid any damage to the unit and/or harness.
● To avoid possible malfunction and damage to the engine, install the unit away
from excessive heat or water/moisture.
● Make sure all connections and wiring are not disconnected, short circuited,
or incorrect. If so, it may cause an electric shock, burn out, or damage to the
vehicle.
● If any unusual noise, scents, and/or vibrations are noticed, consult the dealer
immediately.
● If any unusual noises, scents, and/or vibrations are noticed while driving, please
refer to a factory repair manual.
● Confirm the following before reading the ECU data with this product:
・ The ECU is a factory standard.
・ Data on the ECU is not modified.
● Desorption of the connector, please go Always hold the connector.
・ If you pull the cable, there is a possibility of disconnection.
● Before an automobile inspection and/or repair,It is necessary to remove this
product.
● Daily maintenance on the vehicle is the responsibility of the owner.
Manufacturer's
original connector
５
４pc.
Tie wrap (small)
（Male 4pin Connector）
（Male 3pin Connector）
（Female 4pin Connector）
（Female 3pin Connector）
BOOSTCONTROLLERforABARTH595
取扱説明書
E89671-T41010-00
2018.01発行
Ver. 3-1.01
BOOSTCONTROLLERforABARTH595

ー ３ ー ー ４ ー
１１.Revision of Manual
For questions about this product, any optional, lost, defective and/or damaged
parts, please contact your dealer.
８. Maintenance
９. Repair Service
１０. Product Specifications
BOOST CONTROLLER installation
location
Pressure sensor location (Channel 1)
Connect the harness of BOOST
CONTROLLER
Install BOOST CONTROLLER main
unit
６. Recommended BOOST CONTROLLER installation location and Pressure sensor location
Direction of view
Direction of view
● Do not try to repair the product yourself. Consult with your dealer.
● If any unusual noises, scents, and/or vibrations are noticed while driving,
please refer to a factory repair manual.
● Do not use this product if unusual occurrences should occur to avoid risk of
electrical shock and/or fire. Consult with the dealer immediately.
● Operating Voltage ………………………… DC5V - 16V
● Operating Temperature …………………… -20 - 100℃
● Outer Size …………………………………… 90.0 x 84.0 x 35.0mm
WARNING
CAUTION
Details
1st Edition
Date
2021/09
Rev. Number
3-1.01
Symptom
The check lamp blinks only
when the BOOST CONT
ROLLER is connected.
Or boost does not go up.
BOOST CONTROLLER's
LED is blinking.
Factory boost meter
doesn't display an increase
in pressure.
Cause
The connector is
disconnected.
Wire harness is broken.
BOOST CONTROLLER is
out of order.
Data writing failed with
Easy Writer exclusive
for Power Editor.
Features of factory boost
meter.
Measure
Reseat connector of BOOST
CONTROLLER main unit and
pressure sensor connector.
Request repair of BOOST
CONTROLLER.
Write data again with Easy Writer
exclusive for Power Editor.
Factory boost meter might not
display an increase in pressure.
This issue doesn't affect vehicle
operation.
When the product does not function properly, check the following to see if there
is any measure against the symptom appeared.
７. Troubleshooting
Direction of view
Pressure sensor location (Channel 2)
Connect the harness of BOOST
CONTROLLER
※Sensor is under the circle.
We recommend to remove the air intake before installation.
※Sensor is right under the battery case.
Please remove the battery and battery case to exchange.