HMS Networks Intesis 700 Series User manual

Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels
IN704DAL1280000 GATEWAY
USER MANUAL
Version 1.0.0
Publicaon date 2023-10-31
ENGLISH

Copyright © 2023 Intesis
Disclaimer
The informaon in this document is for informaonal purposes only. Please inform HMS Networks of any
inaccuracies or omissions found in this document. HMS Networks disclaims any responsibility or liability for any
errors that may appear in this document.
HMS Networks reserves the right to modify its products in line with its policy of connuous product
development. The informaon in this document shall therefore not be construed as a commitment on the
part of HMS Networks and is subject to change without noce. HMS Networks makes no commitment to update
or keep current the informaon in this document.
The data, examples and illustraons found in this document are included for illustrave purposes and are only
intended to help improve understanding of the funconality and handling of the product. In view of the wide
range of possible applicaons of the product, and because of the many variables and requirements associated
with any parcular implementaon, HMS Networks cannot assume responsibility or liability for actual use
based on the data, examples or illustraons included in this document nor for any damages incurred during
installaon of the product. Those responsible for the use of the product must acquire sucient knowledge in
order to ensure that the product is used correctly in their specic applicaon and that the applicaon meets all
performance and safety requirements including any applicable laws, regulaons, codes and standards. Further,
HMS Networks will under no circumstances assume liability or responsibility for any problems that may arise as
a result from the use of undocumented features or funconal side eects found outside the documented scope
of the product. The eects caused by any direct or indirect use of such aspects of the product are undened and
may include e.g. compability issues and stability issues.

Table of Contents
1. General Informaon ................................................................................................................ 1
1.1. Intended Use of the User Manual ........................................................................................ 1
1.2. General Safety Informaon ................................................................................................ 1
1.3. Admonion Messages and Symbols ..................................................................................... 1
2. Descripon and Order Codes ..................................................................................................... 3
3. Overview ............................................................................................................................... 4
3.1. Inside the Package ............................................................................................................ 5
3.2. Main Features .................................................................................................................. 5
3.3. General Funconality ........................................................................................................ 6
3.4. Gateway Capacity ............................................................................................................. 6
3.5. DALI Supported Device Types .............................................................................................. 7
4. Hardware ............................................................................................................................... 8
4.1. Mounng ........................................................................................................................ 8
4.2. Connecon ..................................................................................................................... 9
4.2.1. Gateway Connectors .................................................................................................. 9
4.2.2. Connecon Procedure for DALI ................................................................................... 11
4.2.3. Connecon Procedure for Modbus .............................................................................. 11
4.2.4. Connecon Procedure for BACnet ............................................................................... 12
4.2.5. Connecon to a PC for Conguraon ........................................................................... 12
4.3. LED Indicators ................................................................................................................. 12
4.4. Buons ......................................................................................................................... 13
4.5. Technical Specicaons .................................................................................................... 15
4.6. Dimensions .................................................................................................................... 16
5. Available Applicaons ............................................................................................................. 17
5.1. DALI to BACnet/IP ............................................................................................................ 17
5.1.1. BACnet Objects ....................................................................................................... 17
5.2. DALI to Modbus TCP ........................................................................................................ 26
5.2.1. Modbus Registers .................................................................................................... 26
6. Late Conguraon: Change the Gateway's Protocol ..................................................................... 37
Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels
USER MANUAL Version 1.0.0

1. General Informaon
1.1. Intended Use of the User Manual
This manual contains the main features of this Intesis gateway and the instrucons for its appropriate
installaon, conguraon, and operaon.
The contents of this manual should be brought to the aenon of any person who installs, congures, or
operates this gateway or any associated equipment.
Keep this manual for future reference during the installaon, conguraon, and operaon.
1.2. General Safety Informaon
IMPORTANT
Follow these instrucons carefully. Improper work may seriously harm your health and damage the
gateway and/or any other equipment connected to it.
Only technical personnel, following these instrucons and the country legislaon for installing electrical
equipment, can install and manipulate this gateway.
Install this gateway indoors, in a restricted access locaon, avoiding exposure to direct solar radiaon, water, high
relave humidity, or dust.
All wires (for communicaon and power supply, if needed) must only be connected to networks with indoor
wiring. All communicaon ports are considered for indoor use and must only be connected to SELV circuits.
Disconnect all systems from their power source before manipulang and connecng them to the gateway.
Use a circuit breaker before the power supply. Rang: 250 V, 6 A.
Respect the expected polarity of power and communicaon cables when connecng them to the gateway.
1.3. Admonion Messages and Symbols
DANGER
Instrucons that must be followed to avoid an imminently hazardous situaon that, if not avoided,
will result in death or severe injury.
WARNING
Instrucons that must be followed to avoid a potenally hazardous situaon that, if not avoided,
could result in death or severe injury.
CAUTION
Instrucon that must be followed to avoid a potenally hazardous situaon that, if not avoided,
could result in minor or moderate injury.
General Informaon Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels
USER MANUAL Version 1.0.0 Page 1 of 37

IMPORTANT
Instrucon that must be followed to avoid a risk of reduced funconality and/or damage to the
equipment or to avoid a network security risk.
NOTE
Addional informaon which may facilitate installaon and/or operaon.
TIP
Helpful advice and suggesons.
NOTICE
Remarkable Informaon.
Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels Admonion Messages and Symbols
Page 2 of 37 USER MANUAL Version 1.0.0

2. Descripon and Order Codes
Intesis® IN704DAL1280000 Gateway.
DALI-2 to Modbus TCP or BACnet/IP Server Applicaon with 2 DALI Channels.
ORDER CODE INTESIS MAPS TEMPLATE APPLICATION
IN704DAL1280000
IN-MBS-DALI-128 Intesis DALI to Modbus Server Gateway
IN-BAC-DALI-128 Intesis DALI to BACnet Server Gateway
LEGACY ORDER CODES
INBACDAL1280200 / INMBSDAL1280200
Descripon and Order Codes Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels
USER MANUAL Version 1.0.0 Page 3 of 37

3. Overview
This IN704DAL1280000 gateway supports two applicaons.
Gateway's client interface ↔ Gateway's server interface
DALI to
BACnet/IP
Modbus TCP
IMPORTANT
This document assumes that the user is familiar with these technologies.
Figure 1. Integraon of DALI devices into BACnet/IP installaons
Figure 2. Integraon of DALI devices into Modbus TCP installaons
Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels Overview
Page 4 of 37 USER MANUAL Version 1.0.0

3.1. Inside the Package
Items included:
• Intesis IN704DAL1280000 gateway
• USB Mini-B type to USB Type-A cable
•Installaon sheet
3.2. Main Features
• DALI-2 cered
• UL cered
• BTL cered
• Two applicaons available: DALI to BACnet/IP and DALI to Modbus TCP
• New color control allows the BMS to control RGB channels and the tunable white funcon for human
centric lighng (HCL)
• New DALI data feature allows the obtaining of energy and diagnosc data directly from the luminaire
• New DALI local control allows push buons, absolute inputs, and occupancy and light sensor control from the
gateway itself
• Two DALI channels available
• BACnet advanced features available (calendars, schedules, trend logs, etc.)
• BACnet explorer funcon: Scan the network to nd all BACnet devices and objects
•Mulple ports:
– 2 x Pluggable terminal block for DALI (2 poles)
– Ethernet
– USB Type-A 2.0 port for ash drive
– USB Mini-B type 2.0 port for connecon to the PC
• DIN rail mounng housing
• 10000 signals of capacity
•Congurable with Intesis user-friendly soware tool (Intesis MAPS)
• 10 LED indicator matrix
Inside the Package Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels
USER MANUAL Version 1.0.0 Page 5 of 37

3.3. General Funconality
This Intesis IN704DAL1280000 gateway enables data exchange between installaons and devices based on the
DALI protocol and control systems based on BACnet or Modbus.
To do so, the gateway is connuously aware of both sides: the control system (supervisor, BMS, client device,
etc.) and the DALI installaons or devices to be integrated. The gateway obtains updated readings for the points
congured in it. With every read, the new values are updated in the gateway's memory and become available
for the control system side. When a change in any point congured as output in the gateway is detected (that is,
wrien from the control system side), the corresponding acon in the DALI device is performed.
3.4. Gateway Capacity
Table 1. For DALI-2 to BACnet server
Supported elements BACnet
Maximum number of independent DALI channels 2
Maximum number of DALI ECG addresses per line 64
Maximum number of DALI input devices per line 641
Maximum number of instances per input device 10
Maximum number of signals per gateway 100002
DALI guaranteed current 230 mA
Table 2. For DALI-2 to Modbus server
Supported elements Modbus
Maximum number of independent DALI channels 2
Maximum number of DALI ECG addresses per line 64
Maximum number of DALI input devices per line 641
Maximum number of instances per input device 10
Maximum number of simultaneous incoming sockets at Modbus TCP side 5
Maximum number of signals per gateway 100002
DALI guaranteed current 230 mA
NOTE
1 We recommend liming this number to 16 when integrang push buons. Realize that push
buons with several instances consume several signals.
The maximum number of DALI devices (ECGs and/or input devices) depends on the sum current
consumpon of the specic devices. The gateway supplies 230 mA to the bus to power the DALI
devices, so if all input devices (sensors) in the bus consume 5 mA, then we can connect 64 ECGs (the
standard denes the maximum consumpon allowed for these devices is 2 mA) and 16 sensors.
64 ECGs * 2 mA + 16 sensors * 5 mA = 208 mA < 230 mA * 90%
As the standard recommends, don’t use the guaranteed current to calculate the maximum number
of DALI devices, but leave 10% of the current for future expansion or tolerances.
2 This is the gateway's total number of signals regardless of wether they are ECGs, sensors, groups,
etc.
Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels General Funconality
Page 6 of 37 USER MANUAL Version 1.0.0

3.5. DALI Supported Device Types
Name Part Device type
Fluorescent lamp 201 0
Self-contained emergency lighng 202 1
LED module 207 6
Color control 209 8
Energy data 252 51
Diagnoscs and maintenance data 253 52
Consult all signals and their characteriscs in Available Applicaons (page 17).
DALI Supported Device Types Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels
USER MANUAL Version 1.0.0 Page 7 of 37

4. Hardware
4.1. Mounng
IMPORTANT
Before mounng, please ensure that the chosen installaon place preserves the gateway from direct
solar radiaon, water, high relave humidity, or dust.
IMPORTANT
Ensure the gateway has sucient clearances for all connecons when mounted. See Dimensions
(page 16).
NOTE
Mount the gateway over a DIN rail, preferably inside a grounded metallic industrial cabinet.
DIN rail mounng
1. Fit the gateway’s top-side clips in the upper edge of the DIN rail.
2. Press the low side of the gateway gently to lock it in the DIN rail.
3. Make sure the gateway is rmly xed.
NOTE
For some DIN rails, to complete step 2, you may need a small screwdriver or similar to pull the
boom clip down.
Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels Hardware
Page 8 of 37 USER MANUAL Version 1.0.0

4.2. Connecon
CAUTION
Disconnect all systems from the power source before manipulang and connecng them to the
gateway.
IMPORTANT
Keep communicaon cables away from power and ground wires.
4.2.1. Gateway Connectors
Connecon Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels
USER MANUAL Version 1.0.0 Page 9 of 37

Connectors' wiring:
IMPORTANT
For all connectors, use solid or stranded wires (twisted or with ferrule).
Cross-secon/gauge per terminal:
• One core: 0.2 .. 2.5 mm2 / 24 .. 11 AWG
• Two cores: 0.2 .. 1.5 mm2 / 24 .. 15 AWG
• Three cores: Not permied
Communicaon ports:
PORT USAGE WIRING
Port A DALI bus A1: N/A A2: N/A A3: DA+ A4: DA-
Ethernet
As a TCP/IP port: BACnet/IP and Modbus
TCP
As a console port: Connecon to a PC for
conguraon purposes
Ethernet cable (CAT5 or higher)
Port B DALI bus B1: DA- B2: DA+ B3: N/A
Port B
EIA-232 N/A N/A
Console Connecon to a PC for conguraon
purposes USB Mini-B type
USB port:
USB Type-A 2.0 connector for saving logs into a USB ash drive.
IMPORTANT
This USB connector does not support HDD devices.
Power supply:
IMPORTANT
The gateway's power supply is disabled by default to prevent the risk of having two power supplies
at the same me in the DALI bus.
The Intesis MAPS templates for this gateway enable the gateway's power supply by default, so if you
want the gateway's power supply to be the main power supply for the DALI bus, leave it enabled (see
the gure below) or uncheck the Power the DALI Bus parameter to disable it.
If the DALI bus is not powered, there will be no communicaon and an error will appear when
tesng the hardware.
If you are using an external power supply, ensure to comply with the following:
• It is a DALI-2 standard power supply cered under the DiiA guidelines.
• Polarity in the DALI bus is the same for both the gateway and the external power supply.
• Be sure you are following the standard DALI guidelines for bus powering.
Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels Connecon
Page 10 of 37 USER MANUAL Version 1.0.0

Figure 3. Gateway's power supply enabling parameter
The gateway's power supply is enabled/disabled from the DALI Channel root in the tree view
NOTE
If you change the status of the Power the DALI Bus parameter, send the project to the gateway
through the Receive/Send tab to apply the new status.
The power supply connector is a green pluggable terminal block (three poles) labeled as Power.
Power rang: 24 VDC, 12 W.
IMPORTANT
• Use SELV-rated NEC class 2 or limited power source (LPS) power supply.
• Respect the polarity.
• Connect the gateway's ground terminal to the installaon grounding.
• A wrong connecon may cause earth loops and damage the Intesis gateway and/or other system
equipment.
4.2.2. Connecon Procedure for DALI
1. Connect the rst DALI channel to the gateway's Port A using its A3 and A4 terminal connectors.
2. Connect the second DALI channel to the gateway's Port B using its B1 and B2 terminal connectors.
4.2.3. Connecon Procedure for Modbus
Connect the Modbus TCP Ethernet cable to the gateway's Ethernet Port. The correct cable to use depends on
where the gateway is connected:
•Connecng directly to a Modbus TCP device: use a crossover Ethernet UTP/FTP CAT5 or higher cable.
•Connecng to a hub or switch of the LAN of the building: use a straight Ethernet UTP/FTP CAT5 or higher
cable.
Connecon Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels
USER MANUAL Version 1.0.0 Page 11 of 37

NOTE
Some devices detect the dierence automacally and adjust themselves.
IMPORTANT
When commissioning the gateway for the rst me, DHCP will be enabled for 30 seconds. Aer that
me, the default IP address 192.168.100.246 will be set.
IMPORTANT
If communicang through the LAN of the building, contact the network administrator and make sure
trac on the used port is allowed through all LAN paths.
4.2.4. Connecon Procedure for BACnet
Connect the BACnet/IP Ethernet cable to the gateway's Ethernet Port. The correct cable to use depends on
where the gateway is connected:
•Connecng directly to a BACnet/IP device: use a crossover Ethernet UTP/FTP CAT5 or higher cable.
•Connecng to a hub or switch of the LAN of the building: use a straight Ethernet UTP/FTP CAT5 or higher
cable.
NOTE
Some devices detect the dierence automacally and adjust themselves.
IMPORTANT
When commissioning the gateway for the rst me, DHCP will be enabled for 30 seconds. Aer that
me, the default IP address 192.168.100.246 will be set.
IMPORTANT
If communicang through the LAN of the building, contact the network administrator and make sure
trac on the used port is allowed through all LAN paths.
4.2.5. Connecon to a PC for Conguraon
Use the supplied USB Mini-B type to USB Type-A cable to connect the gateway through its Console port to a PC
to congure it with Intesis MAPS.
NOTE
You can use the Ethernet Port to connect the gateway and the PC instead.
NOTICE
Find all you need to know about the gateway conguraon and Intesis MAPS in the Intesis MAPS
User manual for IN704DAL1280000.
4.3. LED Indicators
On the front side, ten LEDs indicate the dierent status of the gateway:
Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels LED Indicators
Page 12 of 37 USER MANUAL Version 1.0.0

LED Color Descripon
Run
O No power
Green The gateway is
connected and running
Error
O No error
Red Error
Eth. Link
O No connecon
Green Connecon established
Eth. Spd
O No transmission
Yellow Transming data
Port A TX/RX
O No acvity
TX blinking green
Data packet
transmied to the DALI
network
RX blinking yellow Data packet received
from the DALI network
Port B TX/RX
O No acvity
TX blinking green
Data packet
transmied to the DALI
B network
RX blinking yellow
Data packet received
from the DALI B
network
LED for Buon A Red
This LED turns to
steady red for 30
seconds when you
press Buon A
LED for Buon B
For the DALI-2 to
BACnet applicaon only
Green Link with BACnet/IP
established
O Buon B has been
pressed
4.4. Buons
Buon A
Press the buon once to broadcast a RECALL_MAX_LEVEL for 30 seconds. Press the buon again to broadcast an
OFF.
NOTE
When having a pen drive connected to the gateway's USB connector, press buon A to save the
project or/and the logs to the pen drive.
This behavior can be congured through Intesis MAPS. To know more, see the Intesis MAPS User
manual for IN704DAL1280000.
Buon B
Press the buon once to send an I-Am message to the network.
NOTICE
This funcon for buon B only applies to the DALI to BACnet applicaon.
Buons Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels
USER MANUAL Version 1.0.0 Page 13 of 37

NOTE
When having a pen drive connected to the gateway's USB connector, press buon B to download a
project or/and a rmware version from the pen drive to the gateway.
The gateway will download the last saved project. The project/rmware must be located in the pen
drive root memory, not inside a folder. This funcon of buon B works for BACnet and Modbus.
This behavior can be congured through Intesis MAPS. To know more, see the Intesis MAPS User
manual for IN704DAL1280000.
Buon A + buon B
Follow this procedure to reset the gateway to the factory sengs:
1. Reboot the gateway.
NOTE
To reboot the gateway, disconnect it from the power supply and connect it again.
2. Keep both buons pressed simultaneously while reboong the gateway.
3. Aer 5-10 seconds, all LEDs will light up and out in a cycle from top to boom.
4. Release the buons.
5. The LEDs cycle can take up to 90 seconds unl the process nishes.
Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels Buons
Page 14 of 37 USER MANUAL Version 1.0.0

4.5. Technical Specicaons
Housing
Material: Plasc, type PC (UL 94 V-0)
Color: Light grey (RAL 7035)
Net dimensions: 90x88x56 mm / 3.54x3.46x2.20"
Space needed for connecons: 130x100x100 mm / 5.11x3.93x3.93"
Mounng DIN rail EN 60715 TH35
Wiring
Cross-secon/gauge per terminal:
One core: 0.2 .. 2.5 mm2 (24 .. 11 AWG)
Two cores: 0.2 .. 1.5 mm2 (24 .. 15 AWG)
Three cores: Not permied
Use solid wires or stranded wires (twisted or with ferrule).
Power supply
1 x Green pluggable terminal block (three poles)
24 VDC ±10%, 12 W
Connect the ground terminal ( ) to the installaon grounding
Port A
1 x Green pluggable terminal block (two poles: A1, A2): Not used
1 x Orange pluggable terminal block (two poles) for DALI:
A3: DA+
A4: DA-
DALI guaranteed current: 230 mA
DALI maximum current: 250 mA
Voltage rang: 16 VDC
1500 VDC isolaon from other ports
Ethernet 1 x Ethernet RJ45 10/100BASE-T
Port B
1 x Green pluggable terminal block (three poles)
B1: DA-
B2: DA+
B3: Not used
DALI guaranteed current: 230 mA
DALI maximum current: 250 mA
Voltage rang: 16 VDC
1500 VDC isolaon from other ports (except Port B EIA-232)
Port B EIA-232 1 x DB9 male connector: Not used
USB port
USB A type 2.0 connector
Flash drives only (HDD not supported)
Power consumpon limited to 150 mA
Console port USB Mini-B type 2.0 connector
Baery
Type: Manganese Dioxide Lithium buon baery
Size: 20 mm x 3.2 mm (0.79" x 0.13")
Capacity: 3 V, 255 mA
Buons
2 x Push buons
Buon A
Buon B
LED indicators
10 x LEDs for gateway and communicaon status
2 x Run (Power/Error)
2 x Ethernet Link/Speed
2 x Port A TX/RX
2 x Port B TX/RX
1 x Buon A indicator
1 x Buon B indicator
DIP switches
2 x DIP switch blocks for EIA-485 serial port conguraon:
DIP switch A (SW A): Not used
DIP switch B (SW B): Not used
Operaonal condions Temperature: 0 .. 50°C / 32 .. 140°F
Humidity: 5 .. 95% (No condensaon)
Technical Specicaons Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels
USER MANUAL Version 1.0.0 Page 15 of 37

4.6. Dimensions
Figure 4. Gateway dimensions
Figure 5. Space needed for connecons
Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels Dimensions
Page 16 of 37 USER MANUAL Version 1.0.0

5. Available Applicaons
NOTE
Signals marked as Oponal signals are supported by the gateway but may not be supported by the
server devices of the installaon. Please refer to the technical documentaon of each server device
to know which signals they support.
5.1. DALI to BACnet/IP
NOTICE
Consult the Protocol Implementaon Conformance Statement (PICS) document at hps://
www.intesis.com/docs/bacnet-server-pic-statement.
5.1.1. BACnet Objects
NOTE
For a complete gateway conguraon guide, please refer to the Intesis MAPS User manual for
IN704DAL1280000.
Table 3. All ballasts
Object name Possible values Object type Object instance R/W
Uyxx_Ballast / Lamp Failure 0: OK
1: Ballast / Lamp Failure 3-Binary Input 7000*y+(100*xx)+0 R
Uyxx_Update All ECG Status 0: Update Finished
1: Trigger Update 3-Binary Input 7000*y+(100*xx)+0 RW
Uyxx_Ballast Status
b7: PwrCycle
b6: MissShAdd
b5: ResetSt
b4: FadeRun
b3: BallLimErr
b2: LampPwrOn
b1: LampFail
b0: BalFail
0-Analog Input 7000*y+(100*xx)+0 R
Uyxx_Actual Level 0 .. 100% 0-Analog Input 7000*y+(100*xx)+1 R
Uyxx_Device Type
0: Fluorescent
1: Emergency
6: LED
8: Color control
0-Analog Input 7000*y+(100*xx)+2 R
Uyxx_Physical Minimum Level 0 .. 100% 0-Analog Input 7000*y+(100*xx)+3 R
Uyxx_Min Level 0 .. 100% 0-Analog Input 7000*y+(100*xx)+4 R
Uyxx_Max Level 0 .. 100% 0-Analog Input 7000*y+(100*xx)+5 R
Uyxx_Power On Level 0 .. 100% 0-Analog Input 7000*y+(100*xx)+6 R
Uyxx_System Failure Level 0 .. 100% 0-Analog Input 7000*y+(100*xx)+7 R
Address formula:
y: Channel number (0 .. 1)
xx: Ballast short address (0 .. 63)
Available Applicaons Intesis DALI-2 Protocol Translator with IP Support - 2 DALI Channels
USER MANUAL Version 1.0.0 Page 17 of 37