Hobbico FLITT HCAE11 Series User manual

INSTRUCTION MANUAL
Table of Contents
Safety Precautions 2
Battery Precautions 2
Product Features 3
Contents 3
Specications 3
Location Precautions 3
App 4
Setup 6
Fly 7
Photo/Video 9
Replacement Parts 10
Maintenance 10
Troubleshooting 11
Limited Warranty 11
ittcamera.com2017 © Hobbico HCAE11** OM
TM

2
SAFETY PRECAUTIONS
Follow these safety precautions when operating this or any drone.
●Adult supervision required.
●Always install the propeller guards before ying.
●Calibrate the Flitt accelerometers before each ying session.
●Do not touch the spinning propellers.
●Keep your face and body as well as all spectators away from
the propellers.
●Stay clear of buildings, high voltage wires, trees, shrubbery or
groups of people.
●Don’t y in bad weather conditions, such as in high wind, rain,
or snow.
●Operating Temperature Range: 32ºF to 104ºF (0ºC to 40ºC).
●Always keep Flitt in your line of sight.
●Maintain a safe pilot-to-device distance while ying.
●Flitt is not a toy. If not operated correctly, it could possibly
cause injury to you or spectators and damage to property.
●Do not alter or modify, as doing so may make it unsafe or
unyable.
●You must check the operation of Flitt before every ight to
ensure that it has remained structurally sound.
BATTERY PRECAUTIONS
The Flitt is equipped with a rechargeable 3.7V Lithium
Polymer (LiPo) battery. Please pay attention to the
following cautions for safe use:
●KEEP OUT OF REACH OF CHILDREN.
●LiPo batteries must be recycled or disposed of properly.
●Do not use this product if the Flitt was severely crashed and
the battery possibly damaged.
●Never disassemble, puncture, or modify the Flitt battery.
●Always turn off Flitt power after each use.
●Only charge using a USB 5.0V 2A max power supply.
●Do not charge inside your car.
●Do not leave unattended while charging.
●Allow Flitt to cool for 30 minutes before recharging.
●Always place Flitt battery on a reproof surface while charging.
●Keep away from combustible materials while charging.
●Unplug the charger immediately if it or the battery becomes
hot! However, it is normal for the charger and battery to get
warm. Disconnect from the charger and quickly move to a
reproof location if the battery begins to get hot or smoke!
●Keep a supply of sand accessible when charging. Dumping
sand on the battery will extinguish a LiPo chemical re.
●Always disconnect the charger after charging is complete.

3
PRODUCT FEATURES
●Portable: Fits in your pocket
●Simple operation
●Optical position hold technology
●6 axis gyro stabilization
●1.3MP camera/720P video
●SD Card compatible up to 32G with FAT32 format
●Auto take-off/land
●
Instant sharing of social media
CONTENTS
Flitt Drone
Micro USB Charge Cable
Charger
Battery
Spare Propellers (4)
Quick Start Guide
SPECIFICATIONS**
Weight: 4.06 oz. [115g]
Width: 5.71 in. [145mm]
Length: 5.55 in. [141mm]
Height: 1.26 in. [32mm]
Prop Size: 2.91 in. [74mm]
Size: 7.01 in. [178mm]
(diagonal: prop shaft to prop shaft)
Flight Time: Approximately 7-9 minutes
(**With arms extended, not including the propellers.)
LOCATION PRECAUTIONS
Flitt uses optical technology to hold in place. This works by
taking repeated pictures of the ground and comparing the pixels
from one picture to the next very fast. If it senses a change,
the sensor will command Flitt to adjust its position. While this
technology is incredible, there are some things to watch for that
can confuse the sensor:
●Floors that are shiny and reective may cause Flitt to drift as
as it tries to follow light reections.
●Surfaces that are very consistent, like black asphalt, snow,
or uniform tile oors, can also confuse the sensor and cause
drifting.
●Flying over water or anything that can move will cause Flitt
to drift.
●When it is windy outside and the grass or owers are moving,
it may cause Flitt to drift. If you nd Flitt drifting where you
are at, simply move to an area where the sensor can see
stationary objects.

4
APP
Search the App Store or Google Play for
Apple and the Apple logo are trademarks of Apple, Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.
Android
™
and Google Play are trademarks of Google Inc. Wi-Fi
®
and Wi-Fi Alliance
®
are registered trademarks of Wi-Fi Alliance.
Camera
Video Record
Speed Selector Flash
Gallery Settings
Fine Tuning Buttons
Controls
Altitude Slide Bar
Screen Gesture Swipe
& Frame Your Subject
Instant Share
Instant Share
Memory Card Capacity
Battery Wi-Fi Safety Unlock
One-Tap Take Off / Land
Emergency Landing
Swipe left or right to
rotate the camera
Swipe left or right to
rotate the camera
Camera
Single Shot: To take a picture, press the
camera icon, the volume buttons or “shake”
your mobile device.
Self-Timer: Push and “hold” the camera icon.
Choose timer and then either 3S or 10S.
Multi-Picture Burst: Push and “hold” the camera
icon. Choose Burst, and then choose the number
of pictures you want to take in a burst.
Video
To start recording a video, select the video
icon. To stop, push the square icon.
Speed Selector L
Push this icon to adjust your ight speed. Use
low (L) or medium (M) speeds indoors. If you
have plenty of room to y, use high (H) speed
to y fast.
Emergency
To land immediately, push this button.
Instant Share
This feature loads your pictures or videos to your
favorite social media quickly. You can set this up
before you y. Go to Settings and choose which
social media service you want to use and how you
want to add a caption. Then go back to the main
screen and select the instant share button and
then take another picture. You’ll be prompted to
sign in to your selected service.

5
When ready to y, rst select either instant share 1 or instant share 2.
Next, take pictures or videos as you y. During your ight (for iOS) or
after (for Android), your pictures will be sent over your chosen service.
Flash
Press the Flash Button to cycle through the three Flash modes.
1. Always on. This is the default mode and is recommended so
the LED can be used determine the orientation of the Flitt.
2. Camera ash. This mode turns the LED off except when
capturing a photo.
3. Always off.
Altitude Slide Bar
Slide this control up or down to change the Flitt altitude. When
the control is released, the Flitt will hover at the selected height.
Holding the control down while the Flitt is on the ground will
stop the motors.
Screen Gesture Swipe Control
This part of your screen shows you what the Flitt camera sees.
The image can be moved to the left or the right by swiping the
screen. This rotates Flitt so the camera will see the picture you
want to take.
Frame Your Subject
You can move the image you see on the screen from side to side
by swiping the open screen area. This rotates Flitt so that you
can easily frame your perfect shot! For framing up and down,
use the altitude slider in small movements.
Controls
Use the directional control stick, altitude slide bar, and left/right
swipe area to control the position of Flitt. For easiest control,
make small movements and then let go. To rotate, swipe the
screen left or right. If you want to rotate constantly, swipe one
direction and hold. There are ne tune buttons to compensate
for any slight drift.
The orientation of the controls are as if you were sitting inside Flitt.
So, if you rotate, you may nd that moving left moves Flitt towards
or away from you. With practice, this will become second nature.
Take Off
Push “Take off” when green. For your safety, Flitt will re-lock
after ve seconds to prevent unintentional takeoffs.
Land
The Take Off button will change to a Land button after the Flitt
takes off. Tapping this button will make the Flitt slowly land.
Landing can be stopped by sliding the Altitude Slide Bar up.
Gallery
Tapping this button will display the images and videos that have
been created by the Flitt.
Memory Card Capacity
When an optional memory card is loaded in Flitt, the available
free space is displayed. The Flitt uses a micro memory card
with a capacity of 2 to 32 GB (FAT32 format). A memory card
is not required for operation. However, if you desire high quality
images and video, we recommend using a card.
Battery Charge/Life
The battery life remaining is displayed by this indicator.
White indicates the charge is above 40%
Red (steady) indicates the charge is between 40% and 20%
Red (ashing) indicates the charge is below 20%. (Flitt will
land when battery life drops to 10%.)

6
Settings
This button opens
1. Instant Share Settings where the social media links are selected
2. Camera settings
A. Contrast
B. Brightness
C. Factory default settings for the camera
3. Device settings
A. Enter current name and password
B. Change the current name and password
C. Reset the app settings to the factory default values
4. Help Menu
A. Flitt Quick Start Guide
B. Start Up Slide Show
C. Flitt Manual
D. Go To ittcamera.com
E. About (provides the current app and rmware version)
5. Calibrate section has guides to help correctly calibrate the Flitt sensors.
Calibrate Accelerometer should be performed any time the Flitt
will not remain stable when hovering. Be sure to place Flitt on a level
surface before starting this procedure.
6. Camera Orientation
7. Full Screen Mode
8. Camera Timer.
Turn “ON” so the default camera action is always a 3 second delay.
SETUP
Charge the Battery
1. Unlock the battery.
2. Grip the battery from the
sides and push up.
3. Insert the battery into
the charger, then plug
the charger into any
USB power source.*
●The LED will be solid
while charging and
will ash when nished.
●Always disconnect when nished.
*If the Flitt is left on, it will automatically turn off for safety. If you try
charging the battery immediately, the LED may not turn on. This is
normal. It will reset automatically after approximately 1 hour or you
can do it quickly by unplugging and reconnecting the power cord
while the battery is in the charger.
4. Insert the battery and lock in place.

7
Turn On the Flitt
Push the power button and hold
for a few seconds until the LED
stays on. (The LED will ash while
waiting to connect to the app.)
Open the Arms
Open the arms fully.
Attach the Propeller Guards
Install a prop guard into the end of each
arm. Match A guards to A arms and B
guards to B arms.
Connect Your Phone
Go to Wi-Fi Settings on your phone and
look for the network Flitt-******.
Connect and enter Password: 12345678.
Open the App
Watch the slide show to learn about
the controls and features. The Flitt
LED will be steady when connected
to the app.
FLY
Get Ready
Position Flitt on a level surface with
the camera facing you.
NOTE: In settings, you can set the
camera to face away from you to
capture scenery.
Push “unlock” and hold for 2 seconds.
Wait for the sensors to automatically calibrate.
Push “Take off” when green. For your
safety, Flitt will re-lock after ve seconds to
prevent unintentional takeoffs. NOTE: We
recommend recalibrating the sensors after
a hard landing or crash. Access this feature
through the Settings menu.
Controls
Move slider to change altitude . Move controls in the direction
you want to travel.
A
A
A
B
B
B
6.5 feet [2M]

8
Flight
Flitt uses Optical sensors in order to stay in one area. However, In
order to keep orientation, it is best not to rotate Flitt too much until
you learn how to y comfortably. The front is always the camera
facing towards you or facing away from you (selectable in the app).
Therefore, your left, right, forward, and back movements always
follow the Flitt as if you were sitting inside.
Use Low speed (L) when ying in small areas. Once you get
comfortable, click the speed icon and try ying a little faster using
(M) for Medium speed. This is good for larger indoor rooms. For
outside, you may want to y faster yet. Choose (H) for High speed.
Click again, and you will be back to (L) speed.
When moving the controls, try to start your movements with your
nger in the center of the circle. Then, slowly slide the direction you
want to go. To change altitude, gently move the slider up and down.
To rotate, swipe the open area in order to frame your photo. Note:
We found that the best pictures are taken from 10 feet (3M) from the
camera or less, with the Flitt positioned a little higher and camera
angled down toward your subject.
Land
To land immediately, push
Power Off
Push and hold until the LED turns off.
It’s easiest to fold up Flitt starting with
the back arms rst.
Now head out to your next photo shoot!
Motor Overload Protection
When Flitt makes a hard landing, crashes into a solid object, or
a propeller cannot spin, the motors will turn off to protect the
control board. The app will display a “Motor Shaft Locked” error
when this occurs. Check Flitt for damage before ying.
Trimming
The ne tuning buttons will appear below and to the right of
the Directional Control. These buttons should be used if Flitt
constantly drifts in the same direction in calm conditions. Take
off and let Flitt hover for a few seconds to check its stability. If it
drifts in one direction, use the opposite trim button to correct it.
For example, if the drone drifts to the left, the right trim button
below the Directional Control should be tapped until the drone
stops drifting in that direction.
Land
TAP
The Flitt LED
will ash when
the battery is
getting low.

9
PHOTO/VIDEO
Camera Settings
Contrast and Brightness can be increased or decreased as
needed. NOTE: These settings will not change when the app
is closed and opened again. Factory Reset will center the
adjustments.
Still Photos
Tap the Camera button to take a single photo. The image will
be stored in the Photo Gallery on the phone and on an optional
memory card that can be loaded on the Flitt.
Hold the camera button for 2 seconds to put the Self-timer and
Burst Mode buttons on the screen.
●The Self-Timer has 3 second and 10 second timer options.
Tap the number to start the timer.
●The Burst Mode has options for taking 3, 5, 10 or 15 photos
at the rate of 2 photos per second. Tap the desired number
to start the camera.
Tap the camera button to remove the Self-timer and Burst Mode
buttons from the screen. For the best picture quality, make sure
the lens is clean.
Video
Tap the Video button to start recording a video which will be
stored in the phone’s Photo Gallery and also on the optional
memory card. A timer and Stop button will appear when the
video starts. Tap on the Stop button to end the video.
TIP:
The video camera works best when the Flitt is not moving.
Do not start a video until the Flitt is hovering at the desired height
and distance from you.
Memory Card
A memory card is not included.
For top quality photos and video, use a
micro memory card. (The photos and
video that stream to your device is
reduced quality in order to speed up
and smooth out transmission.)
NOTE: The Flitt is compatible with memory cards up to 32G in
FAT32 format. If you have a card with a different format, you will
need to reformat the card for FAT32 on any computer.
Optical Quality
If the Flitt is in an area where it cannot see a good optical signal,
a message saying “Optical Quality Low” will appear. If you see
this, move to another area.
use
a
a
n
d
s
up

1
0
REPLACEMENT PARTS
1. Propeller Shaft Bearings 1.5x4x2mm (4)
2. Propeller Set (4)
3. Propeller Guard Set (4)
4. Crown Gear w/Shaft Set(2)
5. A/B Motors w/Pinions (2)
6. Arm Set A/B (2)
HCAE6055
HCAE6301
HCAE6302
HCAE6350
HCAE6340
HCAE6370
Not Pictured:
Wall Adapter 100-240V 2A
Charging Box w/USB Cord
Battery 900 MAh
Replacement Parts:
HCAE6310
HCAE6311
HCAE6320
2
4
5
3
1
1
6
66
6
6
6
Short Gearshaft: A Arms
Long Gearshaft: B Arms
MAINTENANCE
Propeller Installation
Be sure to match the letter on the
propeller with the letter on the arm.
Motor/Gear/Bearing Replacement
The Motor, Gear, and Bearings can be replaced without removing
the arm from the Flitt. Remove the 6 screws on the arm cover and
replace the damaged part(s). NOTE: The “A” arms use the shorter
gearshaft and the “B” arms use the longer gearshaft.
Arm Replacement
1. Remove the parts from the damaged arm.
2. Remove the 4 large screws from the frame below each arm.
3. Carefully separate the cover from the frame enough to allow
the arm to be removed.
4. Remove the motor wire from the slot in the damaged arm.
5. Remove the damaged arm from the frame.
6. Install the new arm and reverse these steps.
Flitt Settings Reset
To reset the settings on the Flitt to
factory defaults, press the Reset
Button inside the arm storage
area on the left side of the Flitt (the
Flitt will need to be upside down
to do this). Resetting to factory
default will also restore factory
Wi-Fi name and password.

11
TROUBLESHOOTING
PROBLEM: The Flitt App will not connect to the drone
SOLUTION: (1) Completely close the Flitt app if it is open.
(2) Open the Wi-Fi setting for the phone and select
the Flitt network if not already connected.
(3) Open the Flitt app.
PROBLEM: I cannot remember the Wi-Fi password.
SOLUTION: The default password is 12345678. If the password
has been changed, reset the setting on the Flitt to
restore the default Wi-Fi name and password.
PROBLEM: The LED on the charger will not illuminate.
SOLUTION: With the battery in the charger, unplug the power
cord and reconnect.
PROBLEM:
The picture won’t show on the screen or is very choppy.
SOLUTION: Restart Flitt, re-connect to WiFi, once conrmed that
you are connected, only then open the app.
Other troubleshooting tips can be found at:
http://support.ittcamera.com/index.php
LIMITED WARRANTY
Warranty Overview
• Warranty period: 90 days from the original date of purchase.
• Warranty claims may only be made by the original purchaser.
• Receipt proving valid purchase date and location is required for warranty service.
• Support website: https://cmecamera.com/support
• This Warranty Overview does not include all parts of the warranty. Please read the
full warranty and disclaimers below.
Introduction and Your Rights.
Hobbico, Inc., (“We”) sincerely want our customers to be satised with the Flitt™ micro
folding ying camera products (each, a “Product”) that they purchase from us, but we
understand that despite our strict quality control efforts, on occasion a product could be
defective or cease to perform as warranted.
Set forth on the following pages is the Limited Warranty that applies to your Flitt Camera
Product, certain of its components, and certain accessories or spare parts that you may
purchase from us for use in connection with your Flitt Camera Product.
The next several pages are the Limited Warranty that applies to your Flitt Camera
Product, certain of its components, and certain accessories or spare parts that you may
purchase from us for use in connection with your Flitt Camera Product. Any components
of the Flitt Camera Product, such as motors, that are specically covered by this Limited
Warranty, and that you purchase from us as spares or replacements, are also covered
to the extent provided in this Limited Warranty. While not all parts or components are
covered by this Limited Warranty, as explained below, they may still be eligible for refund
or exchange under the terms of our Refund and Exchange Policy, also provided below.
Under this Limited Warranty, as more fully described in the “Warranty Disclaimers and
Limitation of Liabilities” Section below, we disclaim all implied warranties and, to the
extent that such implied warranties cannot be disclaimed under applicable law, we limit
the duration of such implied warranties. We also disclaim any obligation for certain types
of relief, like incidental and consequential damages. Please note:
• Some States do not allow limitations on how long an implied warranty lasts, so the
above limitation may not apply to you.
• Some States do not allow for the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
• This Warranty gives you specic legal rights, and you may have other rights which
vary from State to State.

12
By using your Product you are agreeing to be bound by the terms of the Limited Warranty
as set out below. Do not use your Product until you have read the terms of the Limited
Warranty. If you do not agree to the terms of the Limited Warranty, do not use the Product
and return it within the return period and in accordance with the Refund and Exchange
Policy, also provided below.
What does this Limited Warranty Cover?
This Limited Warranty (“this Warranty”) covers the original purchaser of a Hobbico, Inc.,
Flitt Camera Product (each, a “Product”) against defects in materials or workmanship
of certain components used in the manufacture of a Product for the duration of the
applicable Warranty Period (as dened below). This Warranty covers the Flitt Camera
Product and the Charger originally furnished with the Product.
Only the original purchaser of the Product is covered as this Warranty is not transferable
to subsequent purchasers or owners of the Product. This Warranty is for residents of the
United States only, and may be updated from time to time.
Excluded from warranty coverage are the Product’s propellers when damaged by a
crash. One set of spare propellers are included with the original product. Additional
propeller sets are available for purchase. Please also see the “What is Not Covered”
Section below for further exclusions.
This Warranty contains the entire agreement between you and Hobbico, Inc.(“we”) with
respect to any warranty and supersedes any and all other written or oral statements,
representations or agreements relating to the subject matter of this Warranty.
This Warranty is for residents of the United States only, and may be updated from time
to time.
How Long does the Warranty Coverage Last?
This Warranty lasts until the earlier to occur of
(a) end of the 90 day warranty period, measured from and beginning with the date
when you received the product or accessory, or
(b) the date when you sell, transfer, give away or otherwise divest ownership of the
covered Product or, if applicable, the part or accessory (the “Warranty Period”), at
which point this Warranty shall expire and be of no further force or effect.
What will Hobbico, Inc., do if I have a valid Warranty Claim?
If you have a valid warranty claim that is submitted during the applicable Warranty
Period, Hobbico, Inc., will repair or replace, at its option, any covered part, component
or system found to be defective in material or workmanship, subject to the exclusions
provided below. If a defect is found and determined to be covered, we will provide the
warranty service as described in this Warranty. The costs of parts and labor required to
return your Product to service if covered by this Warranty will be borne by Hobbico, Inc.
In the event that your Product and claim is covered by this Warranty but we determine
that repair of your Product is not possible or economically feasible, Hobbico, Inc., will
replace your Product with a refurbished Product that is the same as or as close to your
Product as practicable. Please note that any warranty service to be provided will be
provided at our repair facilities, not offsite at a customer’s location. You are responsible
for shipping your product to our repair facility.
By sending the Product, you agree to transfer ownership of the Product to us. We
may not return the original Product to you. When a Product is exchanged or replaced,
any replacement Product becomes your property and the replaced Product becomes
Hobbico’s property.
In the event that Hobbico, Inc., repairs or replaces a defective Product under warranty,
the repaired or replaced Product will continue to be covered by this Warranty through the
end of the original Warranty Period (if any time remains), but not beyond.
What will Hobbico, Inc., do if I Submit a Warranty Claim that is
Determined not to be Valid?
In the event that you send to us a Product that is found not to be eligible for warranty
service under the terms of this Warranty because it has been received after the expiration
of the Warranty Period, or because its coverage has been voided or is otherwise expressly
excluded under the terms set forth below in the “What is Not Covered” section, we
will use reasonable efforts to contact you if you have provided us with valid contact
information and advise you
(i) whether your Product can be repaired,
(ii) the estimated cost of such repair; and
(iii) the estimated time for completion of such repair. If we are able to reach you, we
will follow your instructions as to whether we should repair and return the Product
to you at your cost, or return the Product to you without repair.
In any case, if your warranty claim is determined not to be valid under the terms of this
Limited Warranty, you will be responsible for any costs that you incurred in sending
the Product to us for evaluation as well as any costs that we may incur in shipping
the Product back to you. If you authorize us to repair and return your Product, you will
need to make arrangements to conrm payment of the estimated repair and the cost of

1
3
shipping for returning your Product to you before we will undertake the work. By sending
the Product, you agree to transfer ownership of the Product to us. We may not return
the original Product to you. When a Product is exchanged or replaced, any replacement
Product becomes your property and the replaced Product becomes Hobbico’s property.
What is Not Covered?
In addition to the specic components or parts excluded from warranty coverage and
identied above in the “What Does this Limited Warranty Cover?” section, to the extent
permitted by applicable law, this Warranty excludes or disclaims “implied warranties”
and certain types of damage claims. This Warranty does not apply to cosmetic issues,
unless due to a defect in material or workmanship on a covered component, or to defects
resulting from normal wear and tear of the Product. Please note that Federal law limits or
prohibits the exclusion of implied warranties for “consumer products” and some States
do not allow for the exclusion or limitation of relief, special, incidental, consequential or
indirect damages, or the limitation of liability to specied amounts, so such exclusions
or limitations may not apply to you, but might apply if you have purchased your Product
for use in connection with business activities. The specic Warranty disclaimers and
limitations can be found in “Warranty Disclaimers” below.
Your Product is a sophisticated piece of equipment designed to be used in a certain
manner and only under appropriate conditions. We provide with each Product sold a
“Disclaimer” and “Safety Instructions” along with a “User Manual,” and you hereby
agree to follow the important instructions and warnings provided in those guides. Given
the nature of the Product, and the possible use or uses to which it may be put and the
conditions to which it may be exposed, this Warranty does not cover:
• Any damage, catastrophic failure or crash due to not properly calibrating the Flitt
Camera Device and conducting a “rst ight” in an open, outdoor setting.
• Any damage, catastrophic failure or crash due to your or any user’s failure to follow the
instructions for proper use or storage of your Product as set forth in the Flitt Camera
Disclaimer and Safety Instructions or User Manual.
• Any damage to the Product sustained as a result of dangerous or reckless ight of the
Product, or any operation of the Product that does not follow the usage guidelines set
forth in the Flitt Camera Disclaimer and Safety Instructions or User Manual.
• Any damage to the Product sustained as a result of ying the Product in extreme
or poor weather conditions as described in the Flitt Camera Disclaimer and Safety
Instructions or User Manual.
• Any damage to the Product sustained as a result of using the Product for any purpose
for which it was not designed or intended.
• Any damage to the Product sustained as a result of misuse, incorrect or abnormal
operation resulting in, by way of example only, a crash, collision, re, submersion (in
whole or in part) of the Product in water or any other liquid, or damage due to causing
the Product to carry any additional weight or payload in violation of the Flitt Camera
Disclaimer and Safety Instructions or User Manual.
• Any alteration, disassembly, modication or improper repair of the Product by
unauthorized parties.
• Any damage to the Product due (in whole or in part) to any use of unauthorized
accessories, products or software in combination with the Product.
• Any damage to the Product or any failure of the Product caused by improper storage
including, but not limited to, storing your Product in an unsuitable environment, or
exposing the Product to extreme environmental or weather conditions, such as storms,
strong winds, rain, snow, freezing rain, hail, sand, dust, oil, dirt or other unsuitable
conditions, whether similar or dissimilar to the conditions listed.
• Any damage to the Product caused by operator error or failure, including any issue
attributable to the physical or mental condition of the operator, or otherwise.
• Any damage caused by use, storage, or transportation of the Product in any strong
electromagnetic or electrostatic environments.
• Any damage (or liability) incurred as the result of your failing to comply with U.S.
Federal Aviation Administration (FAA) regulations, local laws or other ordinances
governing the use of drones or unmanned aerial vehicles as such laws, regulations or
rules are in effect from time to time.
• Any damage arising from the installation or removal of accessory retrots or peripheral
equipment constituting a part of the Product.
• Any damage resulting from any replacements, updates or “xes” of the Product’s
software not performed by us.
• Any damage resulting from your failure to keep the Product’s rmware or software
updated with the latest updates that we provide without charge to our customers.
• Any service necessary to restore operability not as a result of a defect in materials
or workmanship, but due to accident, misuse, abuse, neglect, improper handling,
servicing, maintenance or storage of the Product by users.

14
• Any repair or replacement of covers, plastics or appearance parts, such as interior or
exterior nishes or trim, unless such parts affect the Product’s operability and failed as
the result of a defect in material or workmanship within the Warranty Period.
• Any damage caused by the improper or unauthorized replacement of parts, the
installation of retrots, or any preventive maintenance not performed in accordance
with the User Manual.
• Any service made necessary by any external cause over which we have no control
including, without limitation, re, exposure to water or chemicals, alterations, problems
arising from the use of any products, software or hardware not supplied by us, power
failures, surges or shortages, lightning, or repairs by persons other than those expressly
authorized by Hobbico, Inc., to service the Product.
• Any service on any Product on which the FLITT CAMERA label or logo, rating label or
serial number has been altered, defaced or removed.
• Any on-site evaluation, service or repair of a Product.
• Any service made necessary by any modications to the Product not approved in
writing in advance by Hobbico, Inc.
• Any damage caused by using the Product with an inadequately charged battery.
• Any damage caused by the use of a third-party battery or third-party battery charger
(meaning a battery or a battery charger not provided by us along with the Product at
the time of your purchase).
• Any damage caused by the Product being own with known damaged or faulty
components, or with components that have exceeded their prescribed ight life as
described in the User Manual.
• Any reinstallation and recovery of user data, and 3rd party software applications.
• Any claim made by or on behalf of anyone other than the original purchaser of the
Product.
How do I Get Service?
In order to be eligible to receive service for your Product under this Warranty, you should
complete the Return Merchandise Authorization (“RMA”) form for application (download
the form online using the following link: https://cmecamera.com/support) through which
we will attempt to determine, in advance, whether your Product’s condition is covered
under this Warranty.We will require a purchase receipt or invoice with the name, location
and date of purchase. If we provisionally determine that the issue is covered under this
Warranty, you will be issued a case ID number after we receive your RMA form. After
you receive your case ID number, the printed RMA form needs to be included when you
securely wrap, package, and ship the Product to us. The address of the repair center will
be provided on the RMA form available for downloading.
Please take care to package your return carefully. We are not responsible for damage
or a lost Product caused by shipping. Any damage or subsequent failure of the Product
related to inappropriate packaging will result in additional charges for the repair of the
Product. If the Product is returned to us uninsured or under-insured, you assume all risks
of loss or damage to the Product during shipment. By sending the Product, you agree to
transfer ownership of the Product to us. We may not return the original Product to you.
If we provisionally determine that the issue with your Product is not or is unlikely to be
covered by this Warranty, we will examine and evaluate any Product submission that you
may make (which should include a written description of the problem(s)). If we conrm
our initial determination that warranty service or replacement is not available, the cost
(parts and labor) of effecting any repairs and shipping when returning your Product to
you (whether or not you choose to have the out-of-warranty Product repaired) will be
at your expense. Before sending any Product for warranty evaluation (whether or not
covered), you are strongly advised to back up any software, data, etc. stored on the
Product, as Hobbico, Inc., will not be responsible for the loss of, or any damage to or
corruption of, any of such software or data.
We will inspect your Product and use reasonable efforts to contact you within ve (5)
business days of our receipt of your Product. The time required to advise you of the
results of our warranty evaluation may vary case by case. Products covered by this
Warranty will be repaired and returned to you without charge and continue to be covered
by your original warranty based on your original date of purchase.
If your Product is no longer covered by this Warranty (because it is beyond the stated
Warranty Period) or if coverage under this Warranty is excluded or voided for one or
more of the reasons provided in “What is not Covered?” above, we will provide you
with an estimate of the costs required to repair your Product if it can be repaired. If
you authorize such repairs under those circumstances and provide us with necessary
payment information, we will make the repairs and return the repaired Product to you
promptly. If the product has no problem that we can identify, we reserve the right to
charge you for testing and return delivery.

15
WARRANTY DISCLAIMERS.
TO THE MAXIMUM EXTENT PERMITTED BY LAW, THIS LIMITED WARRANTY AND
THE PROCEDURES OR REMEDIES SET FORTH HEREIN ARE EXCLUSIVE AND IN
LIEU OF ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS, WHETHER
ORAL OR WRITTEN, EXPRESS OR IMPLIED. SHENZHEN HOBBICO, INC., MAKES NO
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF
MERCHANTABILITY, NON-INFRINGEMENT AND FITNESS FOR A PARTICULAR PURPOSE
ARE HEREBY DISCLAIMED. IF WE CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED
WARRANTIES UNDER APPLICABLE LAW, THEN ALL IMPLIED WARRANTIES COVERING
THIS PRODUCT, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER
APPLICABLE LAW. IF THE PRODUCT CONSTITUTES A “CONSUMER PRODUCT” UNDER
THE MAGNUSON-MOSS WARRANTY ACT (15 U.S.C. §2301, ET SEQ.) AND YOU ARE
A CUSTOMER RESIDING IN THE UNITED STATES, THE FOREGOING DISCLAIMER OF
IMPLIED WARRANTIES WILL NOT APPLY TO YOU. TO THE EXTENT THAT SUCH IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
CANNOT BE DISCLAIMED UNDER SUCH ACT,THEN SUCH IMPLIED WARRANTIES SHALL
BE VALID ONLY FOR THE WARRANTY PERIOD AND EXPIRE AT THE END THEREOF.
IN NO EVENT HOBBICO, INC., ITS AFFILIATES, OR ANY OF THEIR RESPECTIVE
OFFICERS, DIRECTORS, MEMBERS, PARTNERS, SHAREHOLDERS, EMPLOYEES,
AGENTS, LICENSORS OR SERVICE PROVIDERS (COLLECTIVELY, THE “PROTECTED
ENTITIES”), BE LIABLE FOR PUNITIVE, EXEMPLARY, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, OR FOR AN AMOUNT IN EXCESS OF THE PURCHASE
PRICE OF THE DEFECTIVE PRODUCT. THE PRECEDING LIMITATION WILL APPLY EVEN
IF THE REMEDIES OF REPAIR OR REPLACEMENT OF PRODUCTS COVERED BY THIS
WARRANTY COMPLETELY FAILS OF ITS ESSENTIAL PURPOSE AND EVEN IF THE
PROTECTED ENTITIES HAVE BEEN PREVIOUSLY ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES, WHETHER IN AN ACTION UNDER CONTRACT, NEGLIGENCE, OR ANY OTHER
THEORY, ARISING OUT OF OR IN CONNECTION WITH THE USE OF THE PRODUCT. IN
NO EVENT SHALL THE TOTAL AGGREGATE LIABILITY OF THE PROTECTED ENTITIES TO
YOU FOR ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT
OR TORT, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE OR OTHERWISE) IN THE
AGGREGATE, ARISING FROM THESE TERMS OR YOUR USE OF THE PRODUCT, EXCEED
THE AMOUNT PAID BY YOU FOR THE PRODUCT THAT IS THE SUBJECT OF THE CLAIM.
What about State Laws or Other Laws Governing Warranties
for Consumers?
This Warranty gives you certain specic legal rights, but you also may have other (greater)
rights that vary from State to State, and some of those rights do not allow for them to
be waived or diminished. For example, some States do not allow limitations on how long
an implied warranty lasts, so the above limitation may not apply to you. Similarly, some
States do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitations or exclusions may not apply to you.
This Warranty is not intended (nor would it be permitted) to deny you any warranty rights
to which you are otherwise entitled under applicable Federal law or the laws of the State
or country in which you reside.
Please note that this document may be updated from time by time, and you can always
nd the latest version at:
http://manuals.hobbico.com/hca/hcae11-warranty.pdf