Hobbico Novus UH-1D Huey User manual

❑1. Plug the wall transformer into an AC
outlet. The power indicator light on the wall
transformer will be green and the charge
indicator light will be solid red.
❑2. Plug the battery into the charger. When
the battery is completely charged, the charge
indicator light will turn green (solid or flashing).
Disconnect the battery from the charger.
❑3. Install (8) AA Alkaline batteries into
the transmitter.
❑4. Install the Flight Battery and connect
to the ESC. Close the battery cover.
❑1. Plug the wall transformer into an AC
outlet. The power indicator light on the wall
transformer will be green and the charge
indicator light will be solid red.
❑2. Plug the battery into the charger. When
the battery is completely charged, the charge
indicator light will turn green (solid or flashing).
Disconnect the battery from the charger.
❑3. Install (8) AA Alkaline batteries into
the transmitter.
❑4. Install the Flight Battery and connect
to the ESC. Close the battery cover.
™ ™
™ ™
QUICK START
CHECKLIST
QUICK START
CHECKLIST
WARNING!! The instruction manual must be read completely before operating
the Novus UH-1D Huey. It contains specific warnings about safety and use of the
LiPo flight battery supplied with the Novus UH-1D Huey. All of these warnings and safety
steps must be read and understood before proceeding to the next step.
WARNING!! The instruction manual must be read completely before operating
the Novus UH-1D Huey. It contains specific warnings about safety and use of the
LiPo flight battery supplied with the Novus UH-1D Huey. All of these warnings and safety
steps must be read and understood before proceeding to the next step.
Bell, UH-1D Huey, emblems, logos, and body
designs are trademarks of Textron Innovations
Inc. and are used under license by Hobbico®, Inc.
Bell, UH-1D Huey, emblems, logos, and body
designs are trademarks of Textron Innovations
Inc. and are used under license by Hobbico®, Inc.

❑5. Position throttle stick in lowest position.
❑6. Place the model on a flat surface and
turn the transmitter on. You will notice that
the trim tab indicators are moving and the
navigation lights on the helicopter remain
solid. This is an indication of the linking
process. Allow the helicopter to remain
still and do not move the transmitter sticks
during the linking process.
Two loud tones will be emitted from the
transmitter. After a couple of seconds the
navigation lights will begin flashing rapidly.
This indicates that the binding process is
taking place. The tail navigation light will stop
flashing and the anti-collision beacon on top
of the helicopter will begin operating. This
indicates that the transmitter and helicopter
have bound properly and the helicopter is
now ready for flight. Always step 15 feet
[4.5m] away from the Novus Helicopter
before operating the throttle.
❑5. Position throttle stick in lowest position.
❑6. Place the model on a flat surface and
turn the transmitter on. You will notice that
the trim tab indicators are moving and the
navigation lights on the helicopter remain
solid. This is an indication of the linking
process. Allow the helicopter to remain
still and do not move the transmitter sticks
during the linking process.
Two loud tones will be emitted from the
transmitter. After a couple of seconds the
navigation lights will begin flashing rapidly.
This indicates that the binding process is
taking place. The tail navigation light will stop
flashing and the anti-collision beacon on top
of the helicopter will begin operating. This
indicates that the transmitter and helicopter
have bound properly and the helicopter is
now ready for flight. Always step 15 feet
[4.5m] away from the Novus Helicopter
before operating the throttle.
© 2010 Hobbico®Inc. HMXE0808 Quick Start © 2010 Hobbico®Inc. HMXE0808 Quick Start
Your Novus helicopter has a safe start feature built in that prevents the motor from
activating unless the collective stick has been lowered to the lowest position. If the
motor won’t run and turn the main blades, please make sure the collective stick is all the
way down and leave it there for a couple of seconds. Then try moving the stick up slowly.
❑
7. Transmitter Controls:
Helicopter Climbs
Helicopter ClimbsHelicopter Climbs
Helicopter Moves Forward
Helicopter Moves ForwardHelicopter Moves Forward
Nose Rotates Left
Nose Rotates LeftNose Rotates Left
Helicopter Moves Left
Helicopter Moves LeftHelicopter Moves Left
Your Novus UH-1D Huey is now ready to fly. Please refer to the flying instructions on page
15 in the manual before operating the model.
Your Novus helicopter has a safe start feature built in that prevents the motor from
activating unless the collective stick has been lowered to the lowest position. If the
motor won’t run and turn the main blades, please make sure the collective stick is all the
way down and leave it there for a couple of seconds. Then try moving the stick up slowly.
❑
7. Transmitter Controls:
Helicopter Climbs
Helicopter ClimbsHelicopter Climbs
Helicopter Moves Forward
Helicopter Moves ForwardHelicopter Moves Forward
Nose Rotates Left
Nose Rotates LeftNose Rotates Left
Helicopter Moves Left
Helicopter Moves LeftHelicopter Moves Left
Your Novus UH-1D Huey is now ready to fly. Please refer to the flying instructions on page
15 in the manual before operating the model.