Hobby MQ600 User manual

MQ600 quadcopter Guide Manual
- 1 -
DISTRIBUTORE UFFICIALE PER L’ITALIA

MQ600 quadcopter Guide Manual
- 2 -
Guide List
1. Foreword .....................................................................................................3
2. Important Statement ........................................................................................3
3. Safety Precautions .....................................................................................3
3.1. Far away from Obstacles and the Crowd ...........................................3
3.2. Avoid bad weather conditions in flight .............................................3
3.3. Far away from Heat and Strong Radiation ........................................3
3. . Proper use of the Copter ....................................................................4
3.5. Proper Operation Specification .........................................................4
. MQ600 Configuration ................................................................................4
5. MQ600 Install Steps .................................................................................6
6. Operation Specification ...........................................................................12
6.1. Pre check before Fly .........................................................................12
6.2. Check on power..................................................................................13
6.3. Calibration of Sensors.....................................................................13
6.4. Turn on/ off ......................................................................................13
6.5. Flying Practice ...................................................................................14
7. Extra camera mount & Specifications.....................................................16

MQ600 quadcopter Guide Manual
- 3 -
1. Foreword
To honorable users, thank you for purchasing MQ600 quad copter from
MMC Hobby( TQ-TECH ) in Shenzhen China. Make sure to read the
manual before using quad copter.
2. Safety Statement
MQ600 product is for FPV hobbies, it is not a toy.
Notice: Proper use of this product.
MQ600 is a high tech product which combined with mechanic, electronic,
communication and aeronautic. PNeed to correct assembly and debugging to
fly. This product is suitable for has rich e perience and operation model
aircraft more than 14 years old model aircraft enthusiasts. Please any novice
or beginner should be guided and supervised by e tensive flying e perience
pilot..
MMC Hobby will not responsible for the damages caused by improper
Operation Specification or Install Steps.
Reading the notice and Safety Caution information before assembly
Assemble the product according to the manuals.
Please contact with our distributor if any enquiry.
3. Safety Precautions
Please install, adjust and test are ok before fly out side.
3.1.
3.1.3.1.
3.1.Far away from Obstacles and the Crowd
Make sure to fly the MQ600 in the wide place. Fly it Far away from
Obstacles and the Crowds, high building, high voltage tower.
3.2.
3.2.3.2.
3.2.Avoid bad weather conditions in flight
MQ600 is configured with electronic equipment. Do not fly in rain, snow,
lightening, fog, hail or gust. Do not fly in the moist environment.
3.3.
3.3.3.3.
3.3.Far away heat source and radiation
MQ600 is equipped with flammable materials, can not be used under heat,

MQ600 quadcopter Guide Manual
- 4 -
strong sunshine, magnetic field or any radiation.
3.4.
3.4.3.4.
3.4.Proper use of the Copter
Please maintain, repair, and update with official components from MMC
Hobby. We are not responsible for any use of nonofficial components or
accessories. Use the MQ600 for legal purpose, we are not responsible for
any illegal use.
3.5.
3.5.3.5.
3.5.Proper Operation Specification
MQ600 is only for the adults more than 14 years old. The beginners should
be guided by experience pilot.
Use this product in good spirit condition
Far away from rotation motors and propellers.
Only fly it in good communication signal condition and fully charged
battery.
Switch on the radio system before power on
Disconnect the power supply after flight
Make sure the throttle stick is on the bottom position before power on.
Connect all components correctly
Follow the instructions. Do not do the dangerous flying actions.
Do not fly the MQ600 in low battery. Charge the battery in dry, insulating,
thermal resistant, antistatic field.
4. MQ600 Configuration
MQ600 includes the frame, flight controller, 4 brushless motors, propellers.
It did not include the remote controller and Lipo battery.
MQ600 configuration is below:
1x fuselage upper board fiber glass Fig: Spare parts Item Q01
1x fuselage lower board fiber glass Fig: Spare parts Item Q02
4x Carbon tube Diameter:15mm Length:16cm Fig: Spare parts Item Q03
2x Carbon tube Diameter:16cm Length:16cm Fig:Spare parts Item Q04
2x Carton tube Diameter:8mm Leight: 16cm Fig: Spare parts Item Q05
4x Carton tube fastner Plastic Fig: Spare parts Item Q06

MQ600 quadcopter Guide Manual
- 5 -
4x Motor fastner Plastic Fig: Spare parts Item Q07
2x No.1 fuselage fastner Plastic Fig: Spare parts Item Q08
2x No.2 fuselage fastner Plastic Fig: Spare parts Item Q09
4x Landing gear fastner Plastic Fig: Spare parts Item Q10
4x Landing gear shock absorber Silica gel Fig: Spare parts Q12
2x Removable landing gear Plastic Fig: Spare parts Item Q12
4x Brushless Motor: 4008, KV700 Weight: 80g Fig: Spare parts Item Q13
4x Propellers : MMC1245 Fig: Spare parts Item Q15
4x Propeller and motor fastner: Aluminium alloy CNC Fig: Spare parts Item
Q15
1x Flight controller: MMC10 quadcopter flight controller Fig: Spare parts
Item Q16
1x ESC: QBL10 quadcotper ESC 4 in 1 Fig: Spare parts Item: Q17
Q01 Q02 Q03 Q04
Q05 Q06 Q07 Q08
Q09 Q10 Q11 Q12
Q13 Q14 Q15 Q16

MQ600 quadcopter Guide Manual
- 6 -
Q17
To fly the quadcopter, the customers need to purchase the radio system and
battery by themselves. We recommend the battery 11.4V 2200mAh.
5. MQ600 Install Steps
MQ600 Install Steps steps:
1: Open the package and take out the spare parts.

MQ600 quadcopter Guide Manual
- 7 -
2 Assemble the landing gear
3. Take out the canopy and install the receiver
Notes: The system default setting is FUTABA definition connection. As
showing in the figure, it is connected with WFLY 6CH 2.4G receiver. If
connected with another brand receiver, pleasure refer to the following
connection methods:

MQ600 quadcopter Guide Manual
- 8 -
( Fig 1 )
Do not power on the ESC when connecting with receiver. Otherwise the
motor will run.
Please refer to the Fig 1, if connect with another brand receiver
Connect the receiver to the flight controller board by the servo lines. Fix the
receiver
Symbol "- " this row is GND. It should connect with power ground pin of
receiver
Symbol "+" this row is 5v power supply. It should connect with power ground
pin of receiver
Symbol "～"this row is signal pin. It should be connected with receiver signal
pin
The sequence of the receiver is below: ( Please refer to the radio Operation
Specification manual for the receiver channel definition)

MQ600 quadcopter Guide Manual
- 9 -
Connect the aileron channel of receiver with 1
st
channel of the flight
controller
Connect the elevate channel of receiver with 2
nd
channel of the flight
controller
Connect the throttle channel of receiver with 3
rd
channel of the flight
controller
Connect the rudder channel of receiver with 4nd channel of the flight
controller
Connect any selected 2- switches with 5
th
channel of the flight controller
Connect any selected knob channel of the receiver with the 6
th
channel of
the flight controller. This channel can adjust the flying actions scope. Need
to set the knob switch on your transmitter, and adjust it. When screw the
knob switch increasedly, the flying actions scope will be larger, it is suitable
for the experts pilot. When screw the knob switch decreasingly, the flying
actions scope will be small, it is suitable for the beginners. If not, please
reverse the channel. The users can adjust it accordingly.
4、Connect the landing gear to the frame

MQ600 quadcopter Guide Manual
- 10 -
5. Assemble the propellers
Firstly, set the propellers according to the rotation direction of picture
shown in Fig 2
( Fig 2 )
See the MQ600 below

MQ600 quadcopter Guide Manual
- 11 -
Set the gasket
Install the screws
6 Check the correspondence connection between the ESC and brushless motor
after installation
Connect each ESC with the corresponding motors with the No. See picture below

MQ600 quadcopter Guide Manual
- 12 -
No.1 ESC should connect with No.1 Motor. Be sure that the No.1 Motor
runs clockwise.
No.2 ESC should connect with No.2 Motor. Be sure that the No.2 Motor
runs counter-clockwise.
No.3 ESC should connect with No.3 Motor. Be sure that the No.3 Motor
runs clockwise.
No.4 ESC should connect with No.4 Motor. Be sure that the No.4 Motor
runs counter-clockwise.
6. Operation Specification
6.1. Pre check before Fly
Check whether all component parts are connected well, such as the frame,
landing gear, flight controller board, brushless motor and propellers.
Check whether the connection lines are arranged in the corrected sequence
Check whether the battery is fully charged and fixed under the frame.

MQ600 quadcopter Guide Manual
- 13 -
Check whether 4 motors rotates in correct directions, #1,#3 clockwise, #2,#4
counter clockwise.
Check whether the directions of the blades are corresponding to the motors.
#1,#3 clockwise, #2,#4 counter clockwise. Fix them with the motor shaft
Check whether the motors are assembly firmly, and nothing inside of motors
6.2. Check on power
Please turn on R/C transmitter, and keep throttle channel in the lowest
position and rudder channel is in the center position
Power on the flight controller, the lights on the flight controller will flash. It
means the flight controller works. If not, the flight controller does not work
6.3. Calibration of Sensors
After Check fly of switching on the power, you can calibrate the sensors as
below: Set the quadcopter on the floor, switchover the 5
th
channel for 5-8
times. The calibration sensor is suitable for the initial installation and
unstable flying. No need to calibrate it after flying well.
6.4. Turn on/ off
After sensor calibration, please turn on
Turn on:
Pull throttle to the lowest position, return the other channels to the central
position, and push the rudder to the right. Keep these actions for above 5 seconds,
the motors will turn on at a low speed. Motors will accelerate when push throttle

MQ600 quadcopter Guide Manual
- 14 -
up, until the quadcopter take off.
Turn off
Pull the throttle to the lowest position when motors run, push the rudder to
the left, the motors will decelerate until to stop. Motors should only be turn off
after landing. Please disconnect the battery after flight.

MQ600 quadcopter Guide Manual
- 15 -
6.5. Flight Practice
It's easy to fly MQ600 for hobbies. Please practise in large, keep far away
from the flight and never try to touch the rotating propellers.
Throttle Control Practice
After all checking, power on MQ600 and turn on motors, practice it with
low throttle in a low height, which is less than 1m.
Aileron and Elevate Control Practice
Take off the flight, use the aileron &elevate joysticks to control the MQ600
cruise front, back, left and right directions. Do not fly the flight too fast!
Rudder Control Practice
Take off the flight at 1m, turn the rudder stick to change heading direction.
After much practice, you may take fix-position-hover, all-direction-hover,
coordinated-turn, circle-waypoint, rectangle-waypoint practice.
Practice make perfect! You should practice more and more. Pay attention to
the safety during the practice. The simulator will be helpful.
Camera mount D

MQ600 quadcopter Guide Manual
- 16 -
. Feedback
MMC Hobby ( TQ TECH )
www.MMCHobby.com Email: [e-mail]
www.tq-tech.net.cn Email: [e-mail]
Tel: [phone]
Fax: [phone]
10
th
March, 2012