Holis 4CH User manual

HD 4 Channel and 8 Channel
Digital Video Recorder
Quick Start Guide
8200-1368-01 A0

2
Notice
Please read this manual thoroughly and save it for future use before attempting to connect or operate
this unit.
The information in this manual was current when published. The manufacturer reserves the right to
revise and improve its products. All specifications are therefore subject to change without notice.
Copyright
Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced,
translated or reduced to any electronic medium or machine-readable form, in whole or in part, without
prior written consent of Tyco Security Products. © 2016 Tyco Security Products. All rights reserved.
Customer Service
Thank you for using Tyco Security Products. We support our products through an extensive worldwide
network of dealers. The dealer through whom you originally purchased this product is your point of
contact if you need service or support. Our dealers are empowered to provide the very best in
customer service and support. Dealers should contact Tyco Security Products at [phone] or
[phone] or on the Web at www.holisnvr.com
Trademarks
The trademarks, logos, and service marks displayed on this document are registered in the United
States [or other countries]. Any misuse of the trademarks is strictly prohibited and Tyco Security
Products. will aggressively enforce its intellectual property rights to the fullest extent of the law,
including pursuit of criminal prosecution wherever necessary. All trademarks not owned by Tyco
Security Products. are the property of their respective owners, and are used with permission or allowed
under applicable laws.
Product offerings and specifications are subject to change without notice. Actual products may vary
from photos. Not all products include all features. Availability varies by region; contact your sales
representative.

3
Table of Contents
Important Safeguard and Warning.................................................................................................4
Front Panel –4 channel and 8 channel .........................................................................................6
Rear Panel......................................................................................................................................7
Local Login.....................................................................................................................................8
Web................................................................................................................................................9

4
Important Safeguard and Warning
All installation and operation here should conform to your local electrical safety codes.
We assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
Improper battery use may result in fire, explosion, or personal injury!
When replaceing the battery, please make sure you are using the same model!
Note
All installation and operations should conform to your local electric safety rules.
1. Check Unpacked DVR
When you receive the DVR, please check whether there is any visible damage. The protective
materials used for the package of the DVR can protect most accidental clashes during
transportation. Then you can open the box to check the accessories.
Please check the items in accordance with the list on the warranty card (Remote control is
optional). Finally you can remove the protective film of the DVR.
2. About Front Panel and Rear Panel
The model in the front panel is very important; please check according to your purchase order.
The label in the rear panel will contain the serial number. Usually we need you to present the
serial number when we provide the service after sales.
3. HDD Installation
This series DVR has only one SATA HDD. Please use HDD of 7200rpm or higher.
Please follow the instructions below to install hard disk.
CAUTION
Shut down the device and then unplug the power cable before opening the case to replace
the HDD.

5
1. Loosen the screws of the upper
cover and side panel.
2. Fix four screws in the HDD.
3. Place the HDD in accordance with
the four holes in the bottom.
4. Turn the device upside down
and then turn the screws in
firmly.
5. Connect the HDD cable and
power cable.
6. Put the cover in accordance with the
clip and then place the upper cover
back. Secure the screws in the rear
panel and the side panel.
Note:
You can connect the HDD data cable and the power cable first and then fix the HDD in the
device.
Please pay attention to the front cover. It adopts the vertical sliding design. You need to push the
clip first and then put down.

6
Front Panel –4 channel and 8 channel
The front panel is shown in Figure 1.
Figure 1
Please refer to the following sheet for front panel button information.
Icon
Name
Function
STATUS
Status indicator light
The blue light is on when the device is working
properly.
HDD
HDD status indicator
light
The blue light is on when the HDD is malfunction.
NET
Network status indicator
light
The blue light is on when the network connection is
abnormal.
POWER
Power status indicator light
The blue light is on when the power connection is
OK.
USB2.0 port
Connect to peripheral USB 2.0 storage device,
mouse, burner and etc.

7
Rear Panel
The following figure is using the 8 channel for illustration. See Figure 2.
Figure 2
Please refer to the following sheet for detailed information.
SN
Name
SN
Name
SN
Name
1
Video input
3
Audio output
4
Audio input
5
Video VGA output
6
HDMI port
7
USB port
8
Network port
9
RS-485 input port
10
Power socket
11
On/Off button
12
GND port

8
Local Login
After system booted up, default video display is in multiple-window mode.
Click Enter or left click mouse, you can see the login interface. See Figure 3.
System consists of three accounts:
Username: admin. Password: admin. (administrator, local and network)
Username: default. Password: default. (hidden user) Hidden user “default”is for system interior
use only and cannot be deleted. When there is no login user, hidden user “default”automatically
login. You can set some rights such as monitor for this user so that you can view some channel
views without login.
Note:
For security reason, please modify password after you first login.
You can set to lock an account or not, password login attempt times, and account lock time.
Figure 3

9
Web
Open IE and input DVR address in the address column. For example, if your DVR IP is 10.10.3.16,
then please input http:// 10.10.3.16 in IE address column.
The system pops up a warning to ask you whether to install webrec.cab control or not. Please click
the yes button.
If you can’t download the ActiveX file, please modify your IE security setup.
After installation, the interface is shown as below. See Figure 4.
Please input your user name and password.
Default factory name is admin and password is admin.
Note:
For security reasons, please modify your password after you first login.
Figure 4
Note
This quick start guide is for reference only. Slight difference may be found in the user interface.
All the designs and software here are subject to change without prior written notice.
All trademarks and registered trademarks mentioned are the properties of their respective
owners.
If there is any uncertainty or controversy, please refer to the final explanation of us.
Please visit our website or contact your local service engineer for more information.