Hollyland Solidcom C1 Pro User manual
Solidcom C1 Pro Wireless Stereo Headset
User Manual
V２．0.0
Product Inteaces
1
Volume + Button
Volume - Button
TALK/MUTE Button
(Press the button to switch
between the TALK and MUTE
modes/Press and hold the button
to use the PTT function.)
B Button (Only Functions with a Hub)
(Press the B button to switch to group
B headsets in a system with a hub.)
USB-C Inteace (for Upgrade)
ENC Switch
Batte Compament
Speaker
Power Toggle
A Button
(Press and hold the A button for 5 seconds
for pairing in a system without a hub/Press
the A button to switch to group A headsets
in a system with a hub.)
ENC Microphone
ENC/Battery/Connection Indicator
Operation Guide
Microphone Boom Indicator Description
The states are described below.
2
① ① Indicator light ashes: Unconnected (for remote headsets) *
② Indicator light ashes quickly: Pairing (The indicator light color is subject to the current state during
pairing.)
③ Indicator light stays ON: Master headset turned ON/Remote headset connected successfully
A. A. Steady green light: ENC OFF
B. . Steady blue light: ENC ON
C. Steady red light: MUTE
④ Red indicator light ashes twice: Low batte
Sound Description
① ① "Low batte": The device batte is low.
② Chime sound: The maximum volume is reached.
③ Tick sound: The microphone is turned ON or OFF by rotating the boom.
* The indicator light ashes when a remote headset is not connected, and it stays ON by default when
the master headset is turned ON.
Operation Guide
Button/Switch Description
① ① TALK/MUTE Button
1. Press the button to switch to the TALK mode, and press the button again to switch to the MUTE mode.
In this case, the indicator light turns red.
2. Press and hold the button to switch to the TALK mode (PTT function), and then release the button to
switch to the MUTE mode.
② ENC Switch
①
②
3
1. 1. When the switch is pushed to the ENC position, yellow is displayed and ENC is enabled.
2. When the switch is pushed away from the ENC position, black is displayed and ENC is disabled.
Parameters
Transmission Range 1,100ft (350m) LOS
Frequency Band 1.9 GHz (DECT) (varies by count and region)
Modulation Mode GFSK
TX Power ≤21dBm (125.9 mW)
RX Sensitivity <-90dBm
Batte Capacity 700mAh（2.66Wh）
Charging Time About 2.5 hours
Frequency Response ENC OFF: 150Hz–7kHz (uctuation range: ±6dB)
ENC ON: 150Hz–7kHz (uctuation range: ±10dB）
Signal-to-Noise Ratio
Distoion
Microphone Type Electret
Input SPL >115dBSPL
Output SPL 9４±3dBSPL (@94dBSPL, 1kHz)
ENC ２０dB±２ with two microphones
(relative to environmental noise in all directions)
Net Weight About 170g (6oz) with batteries included
Temperature Range 0℃ to 45℃ (working condition)
–１0℃ to 60℃ (storage condition)
Note: The frequency band and TX power va by count and region.
4
7１±2dB@94dBSPL,1kHz
<1%@94dBSPL, 150Hz–7kHz
5
Safety Precautions
Do not place the product near or inside heating devices (including but not limited to microwave ovens,
induction cookers, electric ovens, electric heaters, pressure cookers, water heaters, and gas stoves) to
prevent the batte from overheating and exploding.
Do not use non-original charging cases, cables, and batteries with the product.
The use of non-original spare pas may cause electric shock, re, explosion, or other dangers.
6
Suppo
If you encounter any problems in using the product or need any help, please contact Hollyland Suppo
Team via the following ways:
HollylandTech
HollylandTech
HollylandTech
suppo@hollyland-tech.com
www.hollyland-tech.com
Hollyland User Group
Statement
All copyrights belong to Shenzhen Hollyland Technology Co., Ltd.
Trademark Statement
Without the written approval of Shenzhen Hollyland Technology Co., Ltd., no organization or individual
may copy or reproduce pa or all of any written or illustrative content and disseminate it in any form.
Note:
Due to product version upgrades or other reasons, this User Manual will be updated from time to time.
Unless otherwise agreed, this document is provided as a guide for use only. All representations,
information, and recommendations in this document do not constitute warranties of any kind,
express, or implied.
7
Any changes or modications not expressly approved by the pay responsible for compliance could
void the user's authority to operate the device. This device complies with Pa 15 of the FCC Rules.
Operations are subject to the following two conditions:
(1) This device may not cause harmful inteerence.
(2) This device must accept any inteerence received, including inteerence that may cause undesired
operations.
The device has been tested and complies with FCC SAR limits.
FCC Radiation Exposure Statement:
This device has been tested and found to comply with the limits for a Class B digital device, pursuant
to Pa 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
inteerence in a residential installation. This device generates, uses, and can radiate radio frequency
energy, and if it is not installed and used in accordance with the instructions, it may cause harmful
inteerence to radio communications. However, there is no guarantee that inteerence will not occur
in a paicular installation. If this device does cause harmful inteerence to radio or television reception,
which can be determined by turning the device o and on, the user is encouraged to t to correct the
inteerence by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the distance between the device and the receiver.
–Connect the device to an outlet on a circuit dierent from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
Note:
FCC Requirement
8
Other manuals for Solidcom C1 Pro
5
Table of contents
Other Hollyland Headset manuals
