Holm dCrest-13 Quick start guide

ARCHITECTURAL & LANDSCAPE LIGHTING |holmlighting.com A Hunter Industries Company
INSTALLATION NOTES: dCrest-13
1. Caution and Safety Instructions
•Qualied personnel must install and/or service
product in a manner consistent with its intended
use and in compliance with the National
Electrical Code, Canadian Electrical Code, and/
or all local and provincial codes.
•Follow all product label information and
installation instructions.
•Turn o power at fuse or circuit breaker before
installation or servicing.
•The use of damaged components may cause an
unsafe condition and void product warranty.
•Do not block light emanating from product in
whole or part.
•Never operate the xture with missing or
damaged lens. Clean lens on a regular basis.
•Entire xture may become extremely hot. Do
not touch hot lens or xture body. Do not touch
the light source at any time.
•Keep all O-rings and sealing surfaces clean
during installation and servicing; failure to do
this may lead to premature failure of the
product.
2. Product Information
•Suitable for mounting within 1.2 meter (4 feet) o the ground.
3YJ8
11.5"/29.3 cm
5.0"/12.7 cm
11.6"/29.5 cm
Tools Needed:
•3/16"Allen wrench (installation)
•9/64"Allen wrench (servicing)
•#1 Phillips screwdriver (servicing)
•#2 Philips screwdriver (servicing)
1/2-14 NPSM

ARCHITECTURAL & LANDSCAPE LIGHTING |holmlighting.com Customer Service 1-844-200-4656
INSTALLATION NOTES: dCrest-13 2
3. Product Installation
Upon installation, use 3/16"Allen wrench to
adjust the angle of the xture according to plan
requirements.
Wiring Chart
BlackLine/Hot/Switching
WhiteCommon
Green (via stud or
green lead)
Ground
Gray*0-10V (-)
Purple*0-10V (+)
FIXTURE
BUILDING
Standard Voltage (SV) Universal Voltage (UV) High Voltage (HV)
Input Power 120V 110V to 277V 220V to 240V
Dimming Phase 0-10V 0-10V
Number of wires 3 5 5
Black, White, Green Black, White, Green,
Purple, Grey
Black, White, Green,
Purple, Grey
*For use with 0-10V driver only
Diagrams
Power Requirements
Note: Ground Mount
(GM-XX) shown
Allen Wrench
Gray Black
White
Purple Green

ARCHITECTURAL & LANDSCAPE LIGHTING |holmlighting.com Customer Service 1-844-200-4656
INSTALLATION NOTES: dCrest-13 3
4. Repair/Replacement Instructions
Standard Optics ( 20º, 40º and 60º)
Unfasten 8-32 x 7/16"screw, using a 9/64"Allen
wrench. Remove cap by liing cap outward. Avoid
using metal tools to protect the powder coat nish.
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:2
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:2
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
Rotate cartridge arm back into the neutral position.
Twist the optic counter clockwise and pull outward
to remove the optic.
Li cartridge arm and turn counter clockwise to
release lock. Pull complete cartridge out of
xture housing.
Unfasten one screw only inside the cartridge using
a Phillips #2 screwdriver.
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
①②
③ ➍
Note: Do not remove adhesive
thermal pads. Premature
failure may result.

ARCHITECTURAL & LANDSCAPE LIGHTING |holmlighting.com Customer Service 1-844-200-4656
INSTALLATION NOTES: dCrest-13 4
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
4. Repair/Replacement Instructions (continued)
Twist and agitate the upper cartridge component
to remove top portion.
Remove the driver clamp using a
#2 Phillips screwdriver.
Unfasten three LED module screws using Phillips #1
screwdriver. Remove reector adapter ring and LED
module from cartridge platform.
Push black, 6-pin connector downward to unlock it
from the cartridge.
⑤⑥
⑦ ⑧
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
NOTE: Remove adhesive label/cover from the
side of the cartridge to expose driver wiring.
Disconnect wire connectors between the
driver and the LED module before completely
removing the LED module.

ARCHITECTURAL & LANDSCAPE LIGHTING |holmlighting.com Customer Service 1-844-200-4656
INSTALLATION NOTES: dCrest-13 5
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
4. Repair/Replacement Instructions (continued)
Remove driver from cartridge.
Disassemble xture using steps 1 through 2 in
previous section.
Unfasten only one screw inside the cartridge using a
Phillips #2 screwdriver.
⑨
① ②
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
Very Wide and Wall Wash Options

ARCHITECTURAL & LANDSCAPE LIGHTING |holmlighting.com Customer Service 1-844-200-4656
INSTALLATION NOTES: dCrest-13 6
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
4. Repair/Replacement Instructions (continued)
Twist and agitate the upper cartridge component to
remove top portion.
Unfasten three LED module screws using Phillips #1
screwdriver. Remove reector adapter ring and LED
module from cartridge platform.
Remove reector from LED module by inserting a
precision slotted screwdriver between the module
and the reector and liing outward. Repeat in a
circular manner around the base of the reector
until reector is disconnected.
Remove the driver clamp using a #2 Phillips
screwdriver.
③④
⑤ ⑥
NOTE: remove adhesive
label/cover from the side
of the cartridge to expose
driver wiring. Disconnect
wire connectors between
the driver and the LED
module.
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
NOTE: use caution
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS

ARCHITECTURAL & LANDSCAPE LIGHTING |holmlighting.com Customer Service 1-844-200-4656
INSTALLATION NOTES: dCrest-13 7
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
E0000 AAA 7/22/2012
REV ECO REVISION DESCRIPTION DRFT DATE APVD
A
B
C
D
4
3
2 1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
CHECKED
BY:
DESIGNER:
SCALE:
DRAWING NO. REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
CREST, ASSEMBLY
JG
21110494XXXX
N/A
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2 1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
5/11/2016
DRAWN
BY:
PRODUCT:
MATERIAL:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
B1 FORMAT REVISION 08/27/12
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
4. Repair/Replacement Instructions (continued)
5. Warranty
Push black, 6-pin connector downward to unlock it
from the cartridge.
Remove driver from cartridge.
⑦⑧
HOLM-001-IN 6/16
STATEMENT OF LIMITED WARRANTY
Hunter®Industries Incorporated (“Hunter”) warrants Holm lighting products to be free of defects in materials or workmanship
under normal use for a period of ve (5) years from the date of invoice. If a defect in a Holm product is discovered during the applicable
warranty period, Hunter will repair or replace, at its option, the product or the defective part. This limited warranty does not extend to
repairs, adjustments, or replacement of Holm products or parts resulting from misuse, negligence, alteration, modication, tampering,
or improper installation and/or maintenance of the product. This warranty extends only to the original installer of the product. If a
defect arises in a Holm product or part during the warranty period, contact the local authorized manufacturer’s representative. Hunter’s
obligation to repair or replace its products as set forth above is the sole and exclusive warranty set forth by Hunter. There are no other
warranties, expressed or implied, including warranties of merchantability and tness for a particular purpose. Hunter will not be liable to
distributor or any other party in strict liability, tort, contract, or any other manner for damages caused or claimed to be caused as a result
of any design or defect in Holm products, or for any special, incidental, consequential, or exemplary damages or any nature, including
without limitation lost business or prots. Notwithstanding the foregoing, if for any reason Hunter is found to be liable, in no event shall
Hunter’s liability exceed the price of the product which gives rise to the claim, loss, or damage.
If you have any questions concerning the warranty or its application, please write to: Customer Service Department -
Holm, 1940 Diamond Street, San Marcos, CA 92078, U.S.A.