HOLTKÖTTER 2560 P1 Series User manual

205 Hardman Avenue South, South Saint Paul, MN 55075
Voice: [phone] • Fax: [phone]
e-mail: [e-mail]
www.holtkoetter.com
ASSEMBLY INSTRUCTIONS FOR
Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.
Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN.
Holtkötter ®and Holtkötter Leuchten®are registered trademarks of Holtkötter. All Rights Reserved.
© Holtkötter
2560*P1
featuring “Dimm System Punkt 1”
(Dimming System Point 1)
Dimm System Point 1
CAUTION, IMPORTANT SAFETY INSTRUCTIONS
This portable luminaire has a polarized plug (one blade is wider than the other) as a feature to
reduce the risk of electrical shock. This plug will fit a polarized outlet only one way. If the plug does
not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
Never use with an extension cord unless plug can be fully inserted. Do not alter the plug.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC
SHOCK, EXPOSURE TO EXCESSIVE UV RADIATION OR
INJURY TO PERSONS
WARNING - To reduce the risk of FIRE, ELECTRIC SHOCK,
EXPOSURE TO EXCESSIVE UV RADIATION OR INJURY TO
PERSONS:
1. Turn off power/unplug and allow to cool before replacing bulb.
2. Bulb gets HOT quickly. Contact only switch/plug when turning on.
3. Do not touch hot lens, guard or enclosure.
4. Do not remain in light if skin feels warm.
5. Do not look directly at lighted lamp.
6. Keep lamp away from materials that burn.
7. Use only with a 150 Watt, bayonet base halogen bulb or smaller bulb.
8. Do not touch the bulb at any time. Use a soft cloth. Oil from skin may damage bulb.
9. Do not operate the portable luminaire with a missing or damaged guard, lamp containment
barrier or UV filter.
SAVE THESE INSTRUCTIONS
Congratulations, you have just purchased the leading-edge dimming technology from Holtkötter
International, Inc. We have specifically designed the “Dimm System Punkt 1” (Dimming System
Point 1 (P1)) to provide specialized features for ease and convenience of use.
Features of the “Dimm System Punkt 1”
Point Dimming - the lamp may be
turned on with a single click of the P1
dimmer.
Soft On - the lamp may be turned on
with a single click of the P1 dimmer. The
lamp will come on low and continue to
brighten to full brightness. This allows the
eye to adjust to a gradual increase in
light.
Soft / Delayed Off - turn the lamp off
with a single click of the P1 dimmer. The
lamp will dim to 60% brightness of the
original setting, remaining briefly at that
level to allow you to exit the room; then
the lamp gradually turns itself off. This
“soft” off provides a few moments of light
after turning the lamp off, rather than
immediate darkness as is the case with
other switches.
Dimming Cycle - to adjust the lamp to
the perfect light level for any situation,
press and hold the P1 dimmer. The dimmer will cycle through all dimming levels.
When the lamp achieves the light level of your choice, release the P1 dimmer.
Tilt Switch - a safety measure is provided with the “Dimm System Punkt 1”. In the
event that the lamp is tipped over, the tilt switch cuts off the power to the lamp.
Care Instructions
Use only a soft, dry cloth to clean. If necessary, a slightly damp, soft cloth can be used to spot
clean. Do not use common household cleaners on lamps or fixtures, as the lacquer on the
outside of the brass may be damaged as a result. Enjoy your new Holtkötter lamp.

e-mail: [e-mail]
www.holtkoetter.com
ASSEMBLY INSTRUCTIONS FOR
Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.
Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN.
Holtkötter ®and Holtkötter Leuchten®are registered trademarks of Holtkötter. All Rights Reserved.
© Holtkötter
Your “Dimm System Punkt 1” lamp must be assembled with the glass shade.
Install the Bulb and Glass Shade
1. Install the new bulb, being careful not to touch the bulb envelope with your bare
hands. Hold the bulb at the porcelain grip, insert it into the socket, push it down slightly
and turn it clockwise.
2. Once the bulb is installed, place the threaded end of the glass over the bulb and onto
the socket.
3. Screw the glass shade down on the fixture until it is firmly in place.
Note of Caution
The recommended replacement bulb for this fixture is the 150 Watt Osram Bayonet Base Halogen
bulb (frosted). Use of other brands of unknown quality may cause a risk of overheating.
Replace the Fuse
An integrated fuse to protect the dimming
circuit can be found in the base of the
lamp. Please check the fuse first, in case
the lamp does not come on. A four (4)
Amp replacement fuse can be found at any
hardware store or Radio Shack store.
2560*P1
featuring “Dimm System Punkt 1”