Holzhof MAX XM 100 RAP User manual

MAX XM 100 RAP line
assembly instructions

TIME SEQUENCE TO E FOLLOWED:
1. STRUTS AND PLATFORMS 6. ENCH
2. ARCHWAYS 7. ATTACHED SWING
3. PARAPETS 8. ATTACHED GYM
4. SLIDE 9. ROOF
5. CLIM ING OARD 10. UNDERGROUND LAYING/ANCHORAGE OF
STRUCTURE

NOTA ENE: it is recommended to fix the bolts
definitively and only insert the caps once the
correct positioning of the elements has been
verified.
NOTE:
-The colours and models in the image
are purely indicative.
-
The platform can be in engineered wood or
wooden planking.
Article
num.
fixing
CODE N.
NAME
1 2 xpe11 Shaped PE nut protection cap
2 2 xpe10 PE nut protection cap
3 4 xpe116 PE cap
4 4
_
ISO7089 Ø8 washer
5 2
_
UNI7473 M8 self-locking nut
7 2
-
UNI4017 M8X155 HEX SCREW

NOTA ENE: it is recommended to fix the bolts definitively and only insert the caps once the correct positioning of
the elements has been verified.
1. Position the archway between the struts and fix it by inserting: 1 x M8 washer (3), 1 x M8x260 TORX screw (2),
1 x Ø25 mm. winged PE cap (1) into the upper part;
1 x PE nut protection cap (4), 1 x M8 washer (3),
1 x M8x260 TORX screw (2), 1 x PE cap (5) into the lower part.
2. Repeat the operation for the opposite side. Fix
the other archways.

NOTA ENE: it is recommended to fix the
bolts definitively and only insert the caps
once the correct positioning of the
elements has been verified.
1. Position the PE parapet between the struts, resting
the two lower fixing wings on the platform and then
fix using:
4 x M8 washer (3)
4 x M8x80 TEL screw (2) WOOD
4 x M6,3x60 TEFR screw (2) ALUMINIUM
4 x Ø25 winged PE cap
2. If necessary, repeat the operation on the othe
r parapets.

Article num.
Default/
Quantity
NAME
1 1 Aladin tower
2 1 Aladin PE archway
3 1 Curved slide h.84
4 4 IS07089 Ø8 washer
5 4
M8x180 TORX screw
6 4 PE cap
1. After having fixed the PE archway (2), place the body of the curved
slide (3) on the platform of the tower (1) and insert the bolts,
necessary for fixing, into the holes present on the slide (3).
2. Check correct positioning, verticality and parallelism. Fix the
bolts definitively and position the caps.
3. Repeat the operation also on the other side of the
slide
NOTE: COLOURS AND MODELS
REPRESENTED ARE PURELY
INDICATIVE

NOTA ENE: it is recommended to fix the
bolts definitively and only insert the caps
once the correct positioning of the elements
has been verified.
1. Insert the (5) M8x70 threaded bars into the
bushes present on the (6) climbing board.
2. Attach the climbing board (6) by introducing
the threaded bars (5) into the pre-drilled holes in
the platform frame; these were previously fixed
by inserting the PE nut protection cap (4)
M8 washer (3), M8 self-locking nut and
(2) and PE cap (1).
1) 2 x PE cap
2) 2 x M8 self-locking nuts
3) 2 x M8 washer
4) 2 x PE nut protection cap
5) 2 x M8x70 LG* threaded bar
6) 2 x M8x50 AL* threaded bar
7) PE climbing board
*LG: Wood
*AL: Aluminium

1) PE cap (4x)
2) PE nut protection cap (4x)
3) M8 washer (4x)
4) M8x130 TEL screw (4x) LG*
5) M6 3x60 TEFR screw (4x) AL*
6) Assembled bench
NOTA ENE: it is recommended
to fix the bolts definitively and
only insert the caps once the
correct positioning of the
elements has been verified.
*
LG: wood
*AL: aluminium

NOTE:
The models represented are purely
indicative.
These instructions are applicable to
Max, Sultan and Aladin roofs.
1. Position the roof on top of the struts with the brackets positioned as in
figure A.
2. Insert the bolts necessary for fixing in sequence, as indicated in figure .
3. Repeat the operation on all 4 struts.
OLT POSITION
OLTS AND SCREWS:
wood: M8x80 TEL SCREW
aluminium: M6,3x60 TEFR SCREW
Article
num.
Default/
Quantity
CODE N.
NAME
1 1
-
PE roof
2 4 xpe10 PE nut protection cap
3 4 xpe116 PE cap
4 4
_
IS07089 Ø8 washer
6 4
-
M8x80 TEL screw

Proceed with fixing, following the instructions illustrated in the
next pages.
2) Fix the beam to the structure strut
4) Fix the
flower-shaped
gable board in
PE
1) Fix the struts to t
he beam
3) Fix the swing, which
can be the plank, cage
or palm type
NOTA ENE: it is recommended to fix the
bolts definitively and only insert the caps
once the correct positioning of the elements
has been verified.