manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Holzhof
  6. •
  7. Play Set & Playground Equipment
  8. •
  9. Holzhof SULTAN User manual

Holzhof SULTAN User manual

This manual suits for next models

4

Other Holzhof Play Set & Playground Equipment manuals

Holzhof ALADIN User manual

Holzhof

Holzhof ALADIN User manual

Holzhof SULTAN XS 312 User manual

Holzhof

Holzhof SULTAN XS 312 User manual

Holzhof LINEA ALADIN XA 100 RAP User manual

Holzhof

Holzhof LINEA ALADIN XA 100 RAP User manual

Holzhof OASIS XOA 100 User manual

Holzhof

Holzhof OASIS XOA 100 User manual

Holzhof MAX XM 100 R line User manual

Holzhof

Holzhof MAX XM 100 R line User manual

Holzhof MAX XM 100 LP PUR User manual

Holzhof

Holzhof MAX XM 100 LP PUR User manual

Holzhof MAX XM 202 RA User manual

Holzhof

Holzhof MAX XM 202 RA User manual

Holzhof XT 100 Dirondello User manual

Holzhof

Holzhof XT 100 Dirondello User manual

Holzhof MAX XM 100 RP line User manual

Holzhof

Holzhof MAX XM 100 RP line User manual

Holzhof MAX XM 100 RAP User manual

Holzhof

Holzhof MAX XM 100 RAP User manual

Holzhof LINEA ALADIN XA 100 RP User manual

Holzhof

Holzhof LINEA ALADIN XA 100 RP User manual

Holzhof MAX XM 209 P User manual

Holzhof

Holzhof MAX XM 209 P User manual

Holzhof MAX XM 208 LP PUR User manual

Holzhof

Holzhof MAX XM 208 LP PUR User manual

Popular Play Set & Playground Equipment manuals by other brands

FUNormous Disney Junior MICKEY MOUSE instruction manual

FUNormous

FUNormous Disney Junior MICKEY MOUSE instruction manual

Outward OUT116 user manual

Outward

Outward OUT116 user manual

GALOPIN ARC02 instruction manual

GALOPIN

GALOPIN ARC02 instruction manual

stilum levis Maintenance instructions

stilum

stilum levis Maintenance instructions

Costway NP10441 user manual

Costway

Costway NP10441 user manual

NOVUM 12124 Assembly instructions

NOVUM

NOVUM 12124 Assembly instructions

Sove 25-200-015 Assembly instructions

Sove

Sove 25-200-015 Assembly instructions

Ledon 1700 Assembly instructions

Ledon

Ledon 1700 Assembly instructions

Terra Bound Solutions Kennel Club Playground manual

Terra Bound Solutions

Terra Bound Solutions Kennel Club Playground manual

Palmako Marta MV100-3510 Assembly, installation and maintenance instructions

Palmako

Palmako Marta MV100-3510 Assembly, installation and maintenance instructions

FEI 32-2400 Assembly guide

FEI

FEI 32-2400 Assembly guide

stilum intera 2 Mounting instructions

stilum

stilum intera 2 Mounting instructions

Play & Leisure 2435507 Aassembly Instructions

Play & Leisure

Play & Leisure 2435507 Aassembly Instructions

Costway TS10033 user manual

Costway

Costway TS10033 user manual

Octonauts OCTOPOD SHARK ADVENTURE PLAYSET quick start guide

Octonauts

Octonauts OCTOPOD SHARK ADVENTURE PLAYSET quick start guide

BOERPLAY Castle Koeningsbourg installation instructions

BOERPLAY

BOERPLAY Castle Koeningsbourg installation instructions

Sove 16-102-070 Assembly instructions

Sove

Sove 16-102-070 Assembly instructions

wendi toys Nordic Lodge Installation and operating instructions

wendi toys

wendi toys Nordic Lodge Installation and operating instructions

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.

assembly instructions
SULTAN / OXI range
XS11 / XOXI11 "Casablanca"
ver.01 - 10.2014
Le misure sono espresse in cm.
firma esecutore :
data : 10.2014
denominazione
e/o cliente :
istruzioni di montaggio
XS11 / XOXI11
nr.
Colori e modelli rappresentati
sono puramente indicativi
pagina 2
PLEASE NOTE: It is advisable to only secure the
nuts and bolts permanently and insert the caps
once it has been checked that all the elements
have been positioned correctly.
Fasten the slide to the tower uprights, inserting
4 TEL M8x80 screws (two per side) for wooden
towers or 4 TEFR 6.3x80 screws for aluminum
towers into the holes at the beginning of the
slide.
Le misure sono espresse in cm.
firma esecutore :
data : 10.2014
denominazione
e/o cliente :
istruzioni di montaggio
XS11 / XOXI11
nr.
Colori e modelli rappresentati
sono puramente indicativi
pagina 3
PLEASE NOTE: It is advisable to only secure the
nuts and bolts permanently and insert the
caps once it has been checked that all the
elements have been positioned correctly.
Secure the climbing board to the tower
inserting from the inside of the tower 2x
TEL M8x130 for wooden towers or 2x
TEFR M6.3x120 for aluminium towers
(including nut covers and caps so that the
nuts and bolts are not exposed).
Article
no. Quantity CODE NO. NAME
IS07089 washer diam. 8
59x59x35 stainless steel angle bar
PE nut cover
PE cap
1. Position the upright and the angle bar on the support surface
and mark the position of the plug.
2. Drill the support surface and position the plug.
3. Secure the angle bar to the support surface and (if not done
previously) to the upright using the appropriate nuts and bolts,
as indicated in the figure.
TEFR 6.3x50 screw
washer diam.10
M10 self-locking nut
M10 self-locking plug
1. Drill a hole.
2. Thoroughly clean the hole using an air
pump and brushes.
3. Insert the anchor in the hole present
on the angle bar.
4. Tighten using a torque wrench.
PLEASE NOTE: It is advisable to only secure the nuts
and bolts permanently and insert the caps once it
has been checked that all the elements have been
positioned correctly.
1. Position the climbing board on the support surface,
marking the position of the plugs.
2. Drill the support surface and position the plugs.
3. Secure the angle bars to the support surface using
appropriate nuts and bolts, as shown in the figure.
Article
no. Quantity CODE NO. NAME
PE nut cover
PE cap
PE climbing board
59x59x35 stainless steel angle bar
M10 self-locking nut
Washer diam.10
M8x115 plug
NOTE: the combination of colours and
models shown is for illustration purposes
only.
The climbing board can measure
84-144-192 cm in height.
Article
no. Quantity CODE NO. NAME
59x59x35 stainless steel angle bar
PE nut cover
PE cap
M10 self-locking nut
M8x115 plug
Washer diam.10
1. Position the slide on the support surface, marking the
position of the plug.
2. Drill the support surface and position the plug.
3. Secure the angle bar to the support surface using the
appropriate nuts and bolts, as indicated in the figure.
NOTE: the combination of colours and models shown is for
illustration purposes only.
The slide can measure 84-144-192 cm in height.
1. Hook the (1) brackets, inserting in sequence:
(2) Pe nut cover, (3) M8 washer, (4) M8x25 hex
screw, (5) Pe cap
1. Make two holes that are 30 cm in diameter and 60 cm deep.
PLEASE NOTE: It is advisable to only secure the
nuts and bolts permanently and insert the caps
once it has been checked that all the elements
have been positioned correctly.
2. Cast a first layer of concrete that is 10 cm thick.
3. Once the concrete has hardened, position the climbing board
brackets in the hole, checking correct alignment of the bottom of the slide
with the level of the finished terrain.
4. Finish casting the concrete as shown in the diagram.
5. Once the concrete has hardened, fill the hole, tamping it with the
left over material until reaching the height of the finished terrain.
1.Make a hole that is 30 cm in diameter and 60 cm deep.
2. Cast a first layer of concrete that is 10 cm thick.
3. Once the concrete has hardened, position the slide brackets
in the hole, checking correct alignment of the bottom
of the slide with the level of the finished terrain.