Holzhof MAX XM 202 RA User manual

MAX XM 202 RA line
assembly
instructions

ASSEMBLY SEQUENCE:
. STRUTS AND PLATFORMS 5. TUBE SLIDE 9. SWING
2. ARCHWAYS 6. PARAPET 0. ROOF
3. CLIMBING BOARD 7. STEPS PANEL . UNDERGROUND LAYING/ANCHORAGE
4. CURVED SLIDE 8. BENCH OF THE STRUCTURE

Article
num.
fixing
CODE N.
NAME
2xpe Shaped PE nut protection cap
22xpe 0 PE nut protection cap
34xpe 6 PE cap
4
4
_
ISO7089 Ø8 washer
5
2
_
UNI7473 M8 self
-
locking nut
7
2
-
UNI40 7
M8X 55
HEX SCREW
NOTA BENE: it is recommended to fix the
bolts definitively and only insert the caps
once the correct positioning of the elements
has been verified.
NOTE:
-The colours and models in the
image are purely indicative.
-
The platform can be in engineered wood or
wooden planking.

NOTA BENE: it is recommended to fix the bolts definitively and only insert the caps once the correct
positioning of the elements has been verified.
. Position the archway between the struts and fix it by inserting: x M8 washer (3), x M8x260 TORX
screw (2), x Ø 25 mm. winged PE cap ( ) into the upper part;
x PE nut protection cap (4), x M8 washer (3),
x M8x260 TORX screw (2), x PE cap (5) into the lower part.
2. Repeat the operation for the opposite side.
Fix the other archways.

NOTA BENE: it is recommended to fix the bolts
definitively and only insert the caps once the
correct positioning of the elements has been
verified.
. Insert the (5) M8x70 threaded bars into the
bushes present on the (6) climbing board.
2. Attach the climbing board (6) by
introducing the threaded bars (5) into
the pre-drilled holes in the platform
frame; these were previously fixed by
inserting the PE nut protection cap (4),
M8 washer (3), M8 self-locking nut and
(2) and PE cap ( ).
) 2 x PE cap
2) 2 x M8 self-locking nuts
3) 2 x M8 washer
4) 2 x PE nut protection cap
5) 2 x M8x70 LG* threaded bar
6) 2 x M8x50 AL* threaded bar
7) PE climbing board
*LG: Wood
*AL: Aluminium

. After having fixed the PE archway (2], place the body of the
(3) curved slide on the platform of the tower ( ) and insert
the bolts necessary for fixing into the holes present on the
slide (3).
2. Check correct positioning, verticality and parallelism. Fix
the bolts definitively and position the caps.
3. Repeat the operation also on the other side of
the slide
NOTE: COLOURS AND MODELS
REPRESENTED ARE PURELY
INDICATIVE
Article
num.
Default/
Quantity
NAME
Aladin tower
2Aladin PE archway
3Curved slide h.84
44IS07089 Ø8 washer
54
M8x 80 TORX screw
64PE cap

) PE cap (6x)
2) PE nut protection cap (6x)
3) M8 washer (6x)
4) M8x 30 (6x) LG* TEL screw
5) M6 3x 00 TEFR screw (6x) AL*
.
Position the curved slide (5) assembled to the tower,
keeping the entry to the tube in correspondence
with the height of the platform,
2. Fix using the relevant bolts, as indicated in the figure.
The following instructions are also valid for the
tube bridge.
NOTA BENE: it is recommended to fix the
bolts definitively and only insert the caps
once the correct positioning of the elements
has been verified.
*
LG: wood
*AL: aluminium

NOTA BENE: it is recommended to fix the
bolts definitively and only insert the caps
once the correct positioning of the elements
has been verified.
. Position the PE parapet between the
struts, resting the two lower fixing
wings on the platform and then fix
using:
4 x M8 washer (3)
4 x M8x80 TEL screw (2) WOOD
4 x M6 3x60 TEFR screw (2) ALUMINIUM
4 x Ø25 winged PE cap
2. If necessary, repeat the operation on the other parapets.

NOTA BENE: it is recommended to fix the
bolts definitively and only insert the caps
once the correct positioning of the elements
has been verified.
. Fix the steps panel ( ) under the tower
platform measuring 44 cm using the bolts
indicated in the figure.
) x steps panel
2) 4 x PE cap \
3) 4 x M8x80 TEL screw LG*
4) 4 x M6 3x60 TEFR screw AL*
5) 4 x M8 washer
6) 4 x PE nut protection cap
*LG: Wood
*AL: aluminium
height from
the ground
h – 80 cm.

) PE cap (4x)
2) PE nut protection cap (4x)
3) M8 washer (4x)
4) M8x 30 TEL screw (4x) LG*
5) M6 3x60 TEFR screw (4x) AL*
6) Assembled bench
NOTA BENE: it is
recommended to fix the bolts
definitively and only insert the
caps once the correct
positioning of the elements
has been verified.
*
LG: wood
*AL: aluminium

Proceed with fixing, following the instructions illustrated in
the next pages.
2) Fix the beam to the structure strut
) Fix the struts to the
beam
4) Fix the
flower-shaped
gable board in
PE
3) Fix the swing,
which can be the
plank, cage or palm
type
NOTA BENE: it is recommended to fix the
bolts definitively and only insert the caps
once the correct positioning of the elements
has been verified.

Article num.
Quantity
CODE N.
NAME
14
- M10X120 HEX CREW
24
- 10X110 CUP QUARE CREW
312 XPE116 PE CAP
412 _Ø10 WA HER
54XPE11 HAPED PE NUT PROTECTION CAP
68XPE10 PE CAP
78
- M10 ELF-LOCKING NUT
1. Attach the struts to the beam
using the relevant
bolts as indicated in the figure. Repeat the operation
on all 4 struts.

. Attach the assembled swing body to the beam, introducing the bolts necessary for fixing into the
swing hangers, as indicated in the figure.
NOTE: colours and models represented are purely indicative. The following instructions can also be
applied to swings with iron beams.
Article num.
Quantity
NAME
assembled swing body
22UNI40 7 M8X25 HEX SCREW
32UNI7473 M8 self-locking nut

Article
num.
Quant
ity
CODE N.
NAME
14XPE116 PE CAP
24
- M8X80 HEX CREW OR M6,3X60 ELF-TAPPING CREW
34
- 08 WA HER
44XPE10 PE NUT PROTECTION CAP
52XPE174 ROTATIONALLY-MOULDED GABLE BOARD IN PE
Wooden struts:
Aluminium struts M8x80 TEL CREW:
M6,3x60 ELF-TAPPING CREW
1. Fix the gable board (5) to the struts using the relevant bolts as indicated in
the figure and repeat the operation on the opposite side and for the second
gable board.
NOTE: the models represented are purely indicative.

NOTE:
The models represented are purely
indicative.
These instructions are applicable to
Max, ultan and Aladin roofs.
1. Position the roof on top of the struts with the brackets positioned as in figure
A.
2. Insert the bolts necessary for fixing in sequence, as indicated in figure B.
3. Repeat the operation on all 4 struts.
BOLT POSITION
Article
num.
Default/
Quantity
CODE N.
NAME
-PE roof
24xpe 0 PE nut protection cap
34xpe 6 PE cap
4
4
_
IS07089 Ø8 washer
6
4
_
M8x80 TEL screw

Concrete deck
rubber safety
flooring

. Attach the brackets ( ) by introducing the following in
sequence: PE nut protection cap (2), M8 washer (3), M8x25
HEX screw(4), PE cap (5)
. Excavate two holes with diameter of 30 cm and depth of 60 cm
NOTA BENE: it is recommended to fix the
bolts definitively and only insert the caps
once the correct positioning of the elements
has been verified.
3. When the concrete has set, position the climbing board brackets in
the hole, checking the correct alignment of the lower part of the
climbing board with the finished ground level.
4. Complete concrete casting as per layout.
5. When the concrete has set, fill the hole by compacting the
infill material up to the finished ground level.
2. Cast a first layer of concrete with thickness of 0 cm.

. Excavate a ho
le with diameter of 30 cm and depth of 60 cm
2. Cast a first layer of concrete with thickness of 0 cm.

3. When the concrete has set, position the slide bracket in the
hole, checking the correct alignment of the lower part of the
slide with the finished ground level.

4. Complete concrete
casting as per layout.
5. When the concrete
has set, fill the
excavation hole by
compacting the infill
material up to the
finished ground
level.