Homall T-OCRC811S1 User manual

Scan the QR code in the lower right corner for the installing video if you have any
assembly problem.
Contact us through E-mail: hofficeser[email protected] for more information.
INSTRUCTION

WARNING !
Please read the instructions carefully before assembly, and assemble the
product properly according to the instructions, don’t put in use of the
product before it is fully assembled. For any damage or defective, kindly
contact our online after-sale service staff.
* the features and specifications of the product are subjects to changes
without prior notice
* To avoid product damage and personal injury, assemble the product properly.
* To avoid product damage and personal injury, please check the product’s
load capacity and do not support user’s whole body on the chair arms.
* To avoid personal injury, place the product on the flat ground.
* Do not stand on the product.
* To avoid personally injury, don’t use the damaged product, and dispose
it properly
* Indoor use only
* Only trained people should repair or replace the back angle adjustment
component with energy accumulator contained.
* Please keep the instructions in case of further use.
Please be careful when unpacking, to avoid personal injury and other ricks,
do not touch the handle during assembly and keep the parts out of reach
of the children.
Please keep the product out of reach
of the children, it’s not a toy!
WARNING!

Parts
Check and make sure you get the components on the list, contact us for any missing
Backrest Seat Control unitBase
M6
M8
Casters
Gas lift
Plastic cover left
hand side
Plastic cover
right hand side
Left armrest
Right armrest
Plastic cover Lumbar cushion
M8*20
8
88
4
M8*25
4
M8*30
2
M6*18PQR

Installation step
1. Attach wheels
4. Fix the armrests to the
base of the seat
3. Fix the control unit to
the base of the seat
5.Insert the gas lift into
the control unit
(Please note the
direction of the
control unit should
be on the right)
Click!
2. Install the gas lift and plastic cover
QR
G
J

6.Attach the backrest
to the seat
9. Fix the plastic cover(H)
onto the side of backrest
10. Right Side
8. Right Side
7. Use the Allen key to
make the screws align
in the holes correctly
and screw them in tightly.
Installation step
P
P

Function
6
1 Load capacity up to 330lb
3 Rocking: Pull out the handle to
start rocking. Insert to stop rocking
2 Seat Height adjustment
（Adjusting knob on the right）
4 360 degree swivel

Rocking function
7

1.Please move the product gently to avoid collision;
2.Please keep out of direct sunlight;
3.Please ensure the centre of gravity is on the hydraulic until during use;
4.Please watch your fingers when you adjusting the backrest angle;
5.Please toggle the handle under your seat when adjusting the chair height. do
not to press it down roughly;
6.Please lift the lever gently to raise or lower the height of the chair. Do not pull
it roughly;
7.Do not place any heavy objects on the chair or armrest;
8.Plastic parts will split if chair is exposed to direct sunlight;
9.Please do not use abrasive cleaners on the chairs;
Instruction during use
8

Q &A
Warning!
Keep the chair out of reach of the children!
To avoid personal damage, do not pull the handle during assembly.
Q: How to assemble the chair seat and the chair back?
A: Put all the seat screws in position and do not tighten;
put all the back screws in position and do not tighten;
adjust the seat and back well and tighten all the screws.
Q: How to assemble the seat base and seat?
A: Find the mark “Front”
Find the base side with mark ” Front” , put
all the base screws in potion and tight them a
little, adjust the seat and seat base well, tighten
all the screws.
It is advised that the users check the screws and tighten them up every 6
months, for any parts missing or defective, kindly contact us and we will be
glad to be helpful.
9