Home Accents Holiday 1006185189 User manual

Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a) READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
b) Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor
applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for
proper installation.
c) This seasonal use product is not intended for permanent installation
or use.
d)Donotmountorplaceneargasorelectricheaters,fireplace,candles
or other similar sources of heat.
e)Do not securethe wiring of the product with staples or nails,or place
on sharp hooks or nails.
f) Do not let lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, or when retiring for the
night, or if left unattended.
h) This is an electric product – not a toy! To avoid risk of fire, burns
personalinjury and electric shockitshould not beplayedwith or placed
where small children can reach it.
i) Do not use this product for other than its intended use.
j)Donothangornamentsorotherobjectsfromcord,wire,orlightstring.
k) Do not close doors or windows on the product or extension cords as
this may damage the wire insulation.
l) Do not cover the product with cloth, paper or any material not part of
the product when in use.
m) This product is equipped with push-in type lamps. Do not twist
lamps.
n) This product employs overload protection (fuse). A blown fuse
indicatesan overload or short-circuit situation.Ifthefuseblows,unplug
the product from the outlet. Also unplug any additional strings or
products that may be attached to the product. Replace the fuse as per
the user servicing instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse blows, a
short-circuit may be present and the product should be discarded.
o) Do not move the tree by pulling the tree tips or tree branches.
p) Read and follow all instructions that are on the product or provided
with the product.
q) SAVE THESE INSTRUCTIONS.
Use and Care Instructions
a) When the product is placed on a live tree, the tree should be well
maintained and fresh. Do not place on live trees in which the
needles are brown or break off easily. Keep the tree holder filled
with water.
b) If the product is placed on a tree, the tree should be well secured
and stable.
c) Before using or reusing, inspect product carefully. Discard any
productsthathavecut,damaged,orfrayedwire insulationorcords,
cracks in the lampholders or enclosures, loose connections, or
exposed copper wire.
5FT Snowfall Shimmer Fir Potted Tree
SKU# 1006185189
d) When storing the product, carefully remove the product from
whereverit is placed, including tree, branches, or bushes, to avoid
anyunduestrainorstressontheproductconductors,connections,
and wires.
e) Whennot in use, store neatlyinacool, dry location protected from
sunlight.
Package Contents
A. Tree top
Qty: 1 B. Tree bottom Qty: 1 C. Tree base Qty: 1
D. Fuse
Qty: 4
E. Replacement
bulb
Qty: 4
CAUTION!– ALWAYS UNPLUG YOUR TREE
FROM ITS POWER SOURCE BEFORE ASSEMBLING OR
DISASSEMBLING.
Assembling the tree
Pleaseremove protective covers from the base of the pole for each tree
section before assembling.
Step1.Carefullyinsertbottomsection(B)oftreeintotreebase. (SeeFig.
1)
Step2.Insertthe top section (A) intothe bottom section (B). (See Fig.2)
Step 3. Connect the plug of top section (A) with the end connector of the
bottom section (B) according to the magnified drawing. (See Fig.
3)
Step4. Gentlypullbranchesupandout.Whenadjustingbranchesbesure
that all wires are free of branch hinges. (See Fig. 4)
Step 5. Shape the branches. Starting with tips closest to the pole, shape
onetip to theright,one to theleft and oneat the centerof the main
stem. Repeat pattern for each branch. (See Fig. 5)
Step 6. Plug the power cord from the bottom section (B) into a proper
outlet.
Pre-Assembly
Assembly

User Servicing Instructions
Replace the fuse.
a) Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
b) Open fuse cover. Slide open fuse access cover
on top of attachment plug towards blades.
c) Remove fuse carefully.
d) Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided
with product).
e) Close fuse cover. Slide closed the fuse access cover on top of
attachment plug.
f) Risk of fire. Do not replace attachment plug. Contains a safety
device (fuse) that should not be removed. Discard product if the
attachment plug is damaged.
Replace the lamp.
1. Grasp plug and remove from its power source.
2. Unlock the lock on the bulb socket.
3. Pull bulb AND plastic base straight out of socket. Do not twist bulbs
while you are removing them.
4. Replace burned-out bulb with 3 V, 20 mA LED bulb ONLY.
(Additional bulbs are included for your convenience.)
5. Relock the lock on the bulb socket.
If the new bulb base does not fit in bulb holder, follow these steps:
 Remove the cover.
 Remove the base of the burned-out
bulb by straightening the bulb leads,
and gently pull bulb out.
 Thread leads of new bulb through
holes in old base with one lead in each hole (always match the long
lead of new lamp to the hook of lamp base).
 After bulb is fully inserted into base, bend each lead up so that the
leads will touch the contacts inside the bulb holder.
 Insert the cover.
If connecting to a lighting string that does not have a Wattage (W)
rating {found on the tag within6 inches of the plug} calculate the
wattage as follows: Multiply the current (0.04 A) which is on the
flag-type tag by 120.
For Example: Lighting string is rated 120V, 60Hz, 0.04 Amps.
0.04X120= 4.8 Watts
Add the wattage of each light string together for a total of 216 Watts or
less. (Do not exceed 216 Watts)
CAUTION:
1. To reduce the risk of overheating, replace burned-out lamps promptly.
Use 3.0 Volt, 20 mA LED lamps only.
2. Riskoffire.Thisproductdoesnotcontainlampshunts,whichallowthe
product to operate if one lamp burns out. Replace lamps only with the
spare lamps provided with this product.
3. To reduce the risk of fire and electric shock: a)Do not install on trees
having needles, leaves or branch coverings of metal or materials
which look like metal, and b) Do not mount or support strings in a
manner that can cut or damage wire insulation.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the cord from the wall outlet and then disconnect each
section of the tree.
Step 3. Gently lift the tree top straight up to remove from the bottom
section and fold all branches towards the pole.
Step4. Carefullyplacealltreesectionsintoashippingboxandtapeitshut.
Step 5. Store your tree in a cool, dry place away from sunlight.
CAUTION! – ALWAYS UNPLUG YOUR
TREE FROM ITS POWER SOURCE BEFORE
ATTEMPTING EITHER FUSE OR BULB
REPLACEMENT.
Troubleshooting
Problem Solution
The tree
does not
light
Ensure that connectors of all tree sections are
connected into each other well. Make sure power
cord plug is securely inserted into a working
electrical outlet.
Checkfor blown fuses at the power cordplug. Replace
as needed with the replacement fuses provided.
Check for loose, broken, or missing bulbs and replace
as needed with the replacement bulbs provided.
If you are still experiencing problems with the tree
please call 1-877-527-0313 for instructions.
UL Model No. L2M3-30W-A-L05, L2M3-60W/2F-A-L05