Home Accents Holiday TG90P2621L06 User manual

Christmas Tree
Model: TG90P2621L06
Sku # XXXX XXX XXX
Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
a. READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
When using electrical products, basic precautions should
always be followed, including the following:
b. Do not use seasonal products outdoors unless marked
suitable for indoor and outdoor use. When products are
used in outdoor applications, connect the product to a
Ground Fault Circuit Interrupting (GFCI) outlet. If one is
not provided, contact a qualified electrician for proper
installation.
c. This seasonal product is not intended for permanent
installation or use.
d. Do not mount or place the product near gas or electric
heaters, fireplaces, candles, or other similar sources of
heat.
e. Do not secure the wiring of the product with staples or
nails, or place on sharp hooks or nails.
f. Do not let lamps rest on the supply cord or on any wire.
g. Unplug the product when leaving the house, when
retiring for the night, or if left unattended.
h. This is an electric product and not a toy! To avoid risk of
fire, burns, personal injury and electric shock it should not
be played with or placed where small children can reach it.
i. Do not use this product for other than its intended use.
j. Do not hang ornaments or other objects from cord, wire,
or light string.
k. Do not close doors or windows on the product or exten
sions cords as this may damage the wire insulation.
l. Do not cover the product with cloth, paper, or any materi
al that is not a part of the product when in use.
m. This product is equipped with push-in type lamps. Do not
twist lamps.
n. Read and follow all instructions that are on the product
or provide with the product.
o. SAVE THESE INSTRUCTIONS
Step 1. Grasp the power adapter or power cord plug, and than
unplug from the power outlet.Do not pull the power cord.
LAMP REPLACEMENT
Step 2. Lift up lamp lock tab, then pull the
lamp and plastic lamp base straight
out of the lamp-holder.
Step 3.
Replace with a new spare lamp
provided with this product.
( Reference figure only)
USER SERVICING INSTRUCTIONS
Step 1 . Choose a location near a wall outlet.
Step 2 . Unfold the legs of the tree stand and lay the stand on the floor.
Step 3 . Slide the locking disk of the tree stand down until it snaps into
place.
Assembling the tree
This tree assmebles with Quick Set® technology
---Set up and light up your tree in less than 10 minutes!
Step 1 . Remove the protective caps from the tree bottom and insert the
pole into the tree stand.
Step 2 . Continue by inserting the upper tree section(s) to the lower
section(s) until inserting the tree top.
Step 3 . Shape the branches to your preference by working from the
bottom to the top. When adjusting branches,
ensure that all wires
are free of branch hinges.
Step 4 . Insert the adaptor into the wall outlet. All your lights should now
be lit.
Step 5 . Shape the tree from the bottom to the top. Start with the
branches farthest from the pole – fan out in a star shape,
and continue until the entire tree is shaped.
Step 6. When finished shaping the branches, slightly
upsweep all branch tips for a uniform look.
Assembly
Assembling the tree stand
Top view Side view
TM
NEED HELP?
DO NOT RETURN TO STORE. PLEASE VISIT US AT:
www.polygroupstore.com OR 1-877-527-0313
Pre-Assembly
Package Contents
Part Description Quantity
A Tree top 1
B Tree center, Sticker 2 1
C Tree center, Sticker 1 1
D Tree stand 1

NOTE: If some bulbs do not light or flicker, search for any
loose plugs and/or broken, loose, or missing bulbs. Replace
bulbs promptly with the replacement bulbs provided in
order to maintain the performance and life expectancy of
your tree.
Step 1. Connect the light strings of the tree together and
plug the adaptor into a wall outlet.
Step 2. If the tree comes with a foot pedal, step on the
On/Off button.
Operation
Turning on the tree
This tree package includes hinge pins, washers and bulbs
for any replacement or repair that you need to perform on
your tree. If extra parts are needed, contact the Customer
Service Team at 1-877-527-0313 between the hours of 8 am
and 5 pm EST, Monday through Friday.
Repairing Loose Hinges
Step 1. Place the branch into the slot of the bracket
Step 2. Insert a new hinge pin through the holes of the
bracket and secure with a washer.
Maintenance
1. Before using or reusing, inspect product carefully. Discard
any products that have cut, damaged or frayed wire
insulation or cords, cracks in the lampholders or enclo
sures, loose connections, or exposed copper wire.
2. Before disassembling the tree, unplug the tree and
remove all ornaments and decorations.
3. Gently lift the tree top straight up to remove from the
center section and fold all branches towards the pole.
4. Repeat this step for the center and bottom tree sections.
Spare parts
Use and Care Instructions
Christmas Tree
Model: TG90P2621L06
Sku # XXXX XXX XXX
HOW TO USE THE REMOTE CONTROLLER :
The remote control is for the wired controller only:
(1) REMOVE THE INSULATION TAB OF THE REMOTE CONTROLLER.
(2) PRESS THE BUTTON TO SELECT DIFFERENT FUNCTIONS, REFER
TO “HOW TO USE THE DUAL COLOR LIGHT CONTROLLER”.
(3) TO REPLACE THE BATTERY, OPEN THE BATTERY
COMPARTMENT WITH A COIN. REPLACE WITH A CR2032
BATTERY.
(4) DISPOSE USED BATTERY PROPERLY. OBSERVE LOCAL
REGULATIONS REGARDING DISPOSAL OF HAZARDOUS WASTE.
(5) ENSURE THE BATTERIES ARE INSTALLED CORRECTLY WITH
REGARD TO POLARITY (+ AND -).
(6) WARNING: SMALL PARTS, KEEP AWAY FROM CHILDREN.
(7) DO NOT EXPOSE LIGHT SET TO MOISTURE.
(8) REMOVE BATTERIES WHEN NOT USED FOR AN EXTENDED
PERIOD OF TIME, OR WHEN DEPLETED.
User servicing instructions
Press the selector button on the “Dual Color Light Control
ler” or “Remote Controller” to select among:
TWINKLE, STEADY ON,
SLOW FADE, FAST FADE,
COMBINATION
REMOTE CONTROL INSTRUCTIONS
1. Remove the insultation tab.
2. Press the button to select from different light functions
(see
DUAL COLOR LIGHT CONTROLLER INSTRUCTIONS ).
Light Controller
Selector
Button
Remote
Controller
TM
5. When storing the product, carefully remove the product
from wherever it is placed, including tree, branches, or
bushes, to avoid any undue strain or stress on the
product conductors, connections, and wires. Cover the
protective cap on the poles to
avoid damaging the internal parts.
6. When not in use, store neatly in a cool,
dry location protected from sunlight.
Insulation Tab
DUAL COLOR LIGHT CONTROLLER INSTRUCTIONS:
BATTERY REPLACEMENT
1. Loosen the screw of the battery cover with a screwdriver (not included).
Control box
Adaptor
To Be Plugged
Into Wall
Outlet
Foot Pedal
on/off Switch
Section 2
Tree top
Section 1
Do Not Tamper
Internal Parts
Open the
protective
cap
Do Not Tamper
Internal Parts
Open the
protective
cap
50S
100S
110S
110S
80S
50S

Christmas Tree
Model: TG90P2621L06
Sku # XXXX XXX XXX
TM
CAUTION:
Use only power adaptor that was provided with this product.
Using a different power adaptor will damage the lights and
cause fire, electrical shock hazard.
IMPORTANT SAFETY
INSTRUCTIONS
1. WARNING: SMALL PARTS, KEEP AWAY FROM CHILDREN.
2. Do not expose light set to moisture.
3. Remove batteries when not used for an extended period
of time, or when depleted.
4. Dispose of used batteries properly by following directions
on batteries.
5. Use only CR2032 batteries for the remote controller.
6. Clean the battery contacts prior to battery installation.
7. DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES MAY
EXPLODE OR LEAK.
Troubleshooting
Problem Solution
The tree does
not light
Ensure that all tree sections are
plugged into each other and that the
tree is plugged into the wall. If your
tree came with a foot pedal, step on
the On/Off button.
Check for loose, broken, or missing
bulbs and replace as needed with the
replacement bulbs provided
2. Replace the used battery with a new CR2032 button cell
battery (not included). Make sure that the battery is
installed with the correct polarity (+ and -).
3. Retighten the screw to close and secure the battery cover.
Cover
Battery
CR2032