Home Accents Holiday TG76M2X38D00 User manual

Christmas Tree
Model: TG76M2X38D00
Sku # 1001 052 896
Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
a. READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
When using electrical products, basic precautions should
always be followed, including the following:
b.Do not use seasonal products outdoors unless marked
suitable for indoor and outdoor use. When products are
used in outdoor applications, connect the product to a
Ground Fault Circuit Interrupting (GFCI) outlet. If one is
not provided, contact a qualified electrician for proper
installation.
c. This seasonal product is not intended for permanent
installation or use.
d.Do not mount or place the product near gas or electric
heaters, fireplaces, candles, or other similar sources of
heat.
e. Do not secure the wiring of the product with staples or
nails, or place on sharp hooks or nails.
f. Do not let lamps rest on the supply cord or on any wire.
g. Unplug the product when leaving the house, when
retiring for the night, or if left unattended.
h. This is an electric product and not a toy! To avoid risk of
fire, burns, personal injury and electric shock it should not
be played with or placed where small children can reach it.
i. Do not use this product for other than its intended use.
j. Do not hang ornaments or other objects from cord, wire,
or light string.
k. Do not close doors or windows on the product or exten
sions cords as this may damage the wire insulation.
l. Do not cover the product with cloth, paper, or any materi
al that is not a part of the product when in use.
m.This product is equipped with push-in type lamps. Do not
twist lamps.
n. Read and follow all instructions that are on the product
or provide with the product.
o. SAVE THESE INSTRUCTIONS
Step 1 Grasp the power adapter or power cord plug, and than
unplug from the power outlet.Do not pull the power cord.
LAMP REPLACEMENT
Step 2 Lift up lamp lock tab, then pull the
lamp and plastic lamp base straight
out of the lamp-holder.
Step 3
Replace with a new spare lamp
provided with this product.
( Reference figure only)
USER SERVICING INSTRUCTIONS
80S
70S
40S
70S
40S
Section 3
Section 2
Section 1
Do Not Tamper
Internal Parts
Open the
protective
cover
Do Not Tamper
Internal Parts
Open the
protective
cover
Adaptor
To Be Plugged
Into Wall
Outlet
Control box
*Electrical Rating For The Tree
(For Indoor Use Only)
Input:120V, 60Hz, 0.16A Max.
Output: 29V 0.28A
Pre-Assembly
Package Contents
Part Description Quantity
A Tree top, tag 3 1
B Tree center, tag 2 1
C Tree bottom, tag 1 1
D Tree stand 1
Assembling the tree stand
Assembly
Step 1 Choose a location near a wall outlet.
Step 2 Unfold the legs of the tree stand (D) and lay the stand on
the floor.
Step 3 Slide the locking disk of the tree stand (D) down until it
snaps into place.
This tree assmebles with Quick Set® technology ---Set up and
light up your tree in less than 10 minutes!
Step 1 Remove the protective caps from the tree bottom (C) and
insert the pole into the tree stand (D).
Step 2 Remove the protective caps from the tree center (B) and
insert the pole into the tree bottom (C) .
Step 3 Insert the tree top (A) into the tree center (B).
Step 4 Shape the branches to your preference by working from the
bottom to the top. When adjusting branches, ensure that all
wires are free of branch hinges.
Step 5 Insert the green label extension cord plug into the wall outlet.
All your lights should now be lit.
Step 6 When finished shaping the branches, slightly upsweep all
branch tips for a uniform look.
Assembling the tree

CAUTION:Use only power adaptor that was provided
with this product. Using a different power adaptor will damage
the lights and cause fire, electrical shock hazard.
Christmas Tree
Model: TG76M2X38D00
Sku # 1001 052 896
Troubleshooting
Problem Solution
The tree does
not light
Ensure that all tree sections are
plugged into each other and that the
tree is plugged into the wall. If your
tree came with a foot pedal, step on
the On/Off button.
Check for loose, broken, or missing
bulbs and replace as needed with the
replacement bulbs provided
1. Before using or reusing, inspect product carefully. Discard any
products that have cut, damaged or frayed wire insulation or
cords, cracks in the lampholders or enclosures, loose
connections, or exposed copper wire.
2. Before disassembling the tree, unplug the tree and remove all
ornaments and decorations.
3. Gently lift the tree top straight up to remove from the center
section and fold all branches towards the pole.
4. Repeat this step for the center and bottom tree sections.
5. When storing the product, carefully remove the product from
wherever it is placed, including tree, branches, or bushes, to
avoid any undue strain or stress on the product conductors,
connections, and wires. Cover the
protective cap on the poles to avoid
damaging the internal parts.
6. When not in use, store neatly in a cool,
dry location protected from sunlight.
Use and Care Instructions
NOTE: If some bulbs do not light or flicker, search for any
loose plugs and/or broken, loose, or missing bulbs. Replace
bulbs promptly with the replacement bulbs provided in
order to maintain the performance and life expectancy of
your tree.
Step 1 Connect the light strings of the tree together and
plug the power cord into a wall outlet.
Step 2 If the tree comes with a foot pedal, step on the
On/Off button.
Operation
Turning on the tree
This tree package includes hinge pins, washers and bulbs
for any replacement or repair that you need to perform on
your tree. If extra parts are needed, contact the Customer
Service Team at 1-877-527-0313 between the hours of 8 am
and 5 pm EST, Monday through Friday.
Repairing Loose Hinges
Step 1 Place the branch into the slot of the bracket
Step 2 Insert a new hinge pin through the holes of the
bracket and secure with a washer.
Maintenance
Spare parts
Press the selector button on the “Dual Color Light
Controller” or “Remote Controller” to select among:
(1) CLEAR - MULTI: FADING (2) CLEAR: FADING
(3) CLEAR - MULTI: ALTERNATING (4) CLEAR: STEADY
(5) CLEAR - MULTI: SLOW FADING (6) MULTI: STEADY
(7) MULTI: FADING (8) COMBINATION
HOW TO USE THE DUAL COLOR LIGHT CONTROLLER
AND REMOTE CONTROL:
User servicing instructions
Light Controller
Selector
Button
Remote
Controller
Insulation
Tab Battery
CR2032
Cover
HOW TO USE THE REMOTE CONTROLLER :
The remote control is for the wired controller only:
(1) REMOVE THE INSULATION TAB OF THE REMOTE
CONTROLLER.
(2) PRESS THE BUTTON TO SELECT DIFFERENT
FUNCTIONS, REFER TO “HOW TO USE THE DUAL
COLOR LIGHT CONTROLLER”.
(3) TO REPLACE THE BATTERY, OPEN THE BATTERY
COMPARTMENT WITH A COIN. REPLACE WITH
A CR2032 BATTERY.
(4) DISPOSE USED BATTERY PROPERLY. OBSERVE LOCAL
REGULATIONS REGARDING DISPOSAL
OF HAZARDOUS WASTE.
(5) ENSURE THE BATTERIES ARE INSTALLED CORRECTLY
WITH REGARD TO POLARITY (+ AND -).
(6) WARNING: SMALL PARTS, KEEP AWAY FROM CHILDREN.
(ONLY FOR PRODUCTS WITH AAA BATTERIES).
(7) DO NOT EXPOSE LIGHT SET TO MOISTURE.
(8) REMOVE BATTERIES WHEN NOT USED FOR AN
EXTENDED PERIOD OF TIME, OR WHEN DEPLETED.
(9) CLEAN THE BATTERY CONTACTS PRIOR TO BATTERY
INSTALLATION.
(10) DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES
MAY EXPLODE OR LEAK.