Home Accents Holiday 24SV24386 User manual

USE AND CARE GUIDE
12FT GIANT SIZED SKELLY
USA Item #1010749792
Model #24SV24386
THANK YOU
We appreciate the trust and confidence you have placed in Home Depot through the purchase of this 12ft Giant Sized Skelly. We strive
to continually create quality products designed to enhance your home. Visit us online to see our full line of
products available for your home improvement needs. Thank you for choosing Home Accents Holiday!
Video assembly
instructions
available online
1-855-HD-HOLIDAY (1-855-434-6543)
HOMEDEPOT.COM
Questions, problems, missing parts? Before returning to the store, call Home Accents Holiday
Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday

2
Table of Contents
Safety Information 2
Warranty
Assembly
Operation
3
Pre-Assembly 3
5
14
16
Safety Information
Care and Cleaning
Troubleshooting
WARNING
This item is not a toy and should be used for decoration only. This item contains small parts that can be a choking hazard. Keep all plastic and
wire parts away from children.
1. Please use the adapter supplied by manufacturer.
2. Please assemble item according to instructions. Connect all wires according to matching color.
3. Children should be supervised by adults. Item should not be grabbed, as it becomes a tipping hazard. Keep flammables away from the adapter,
as it heats up during operation.
Please view all instructions carefully before assembling. Save this instruction sheet for future reference.
□Lay product down before a storm or strong winds.
□Don't climb or pull on product.
□Do not add to or modify unless accessory is designed for product
□Assemble and place the product on level surfaces only.
□Don't push or tilt product.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
□Reorient or relocate the receiving antenna.
□Increase the separation between the equipment and receiver.
□Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
□Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's
licence-exempt RSS(s).Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
BATTERY WARNING:
Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium) batteries. Do not mix old and new batteries. Rechargeable
batteries to be removed from the product before being charged. Only batteries of the same or equivalent type as recommended are to be used.
Rechargeable batteries are only to be charged under adult supervision. Non-rechargeable batteries are not to be recharged. Batteries are to be
inserted with the correct polarity. Remove batteries if consumed or if product is to be left unused for a long time. The supply terminals are not
to be short-circuited. Dispose of batteries safely. DO NOT DISPOSE OF BATTERIES IN FIRE, BATTERIES MAY EXPLODE OR LEAK
16
16
Service Parts
....................................
............................................
........................................
Tools Required 3
Package Contents 4
...................................
................................
....................................
...................................
...................................
...................................
...................................

3 WWW.HOMEDEPOT.COM
Please contact 1-855-434-6543 (1-855-HD-HOLIDAY) for further assistance.
Pre-Assembly
PLANNING INSTALLATION
Estimate installation time: 1 Hour
Number of people required: 2 - 3 People
TOOLS REQUIRED
M6 hex wrench (included) Small phillips
screwdriver (not included)
Warranty
The 12ft Giant Sized Skelly is intended for seasonal use and does not have a warranty. In the event you experience a technical malfunc-
tion, damage, or missing parts upon purchase, please contact customer service (as noted on page 1 and 17) within 90 days of the date
of purchase. The customer service team will assist you with troubleshooting / replacement parts depending on the availability of the
item. Replacements do not cover normal wear and tear, damage incurred due to misuse, parts not assembled or installed in accordance
with the instruction manual, repairs or alternations made outside source, store display products, third party purchases, or full product
replacements. All part requests must be accompanied with proof of purchase.

4
Pre-Assembly (continued)
PACKAGE CONTENTS
Part Description Quantity
A Base 1
B Right Foot 1
C Left Foot 1
D Right Lower Support Pole 1
E Left Lower Support Pole 1
F Right Shin 1
G Left Shin 1
1
1
4
1
1
4
1
H Upper Support Pole 2
I Right Femur 1
J Left Femur 1
K Pelvis 1
L Spinal Support 1
M Rib Cage 1
N Right Humerus 1
O Left Humerus 1
P Right Forearm 1
Part Description Quantity
Q Left Forearm
R Head
S Base Stabilizer
T Loop Screw (M8*130mm)
U Cable
V Stake
W Adapter *
1
X Remote Control
MODE/
MODE/
MODO
ENCENDER
•APAGAR
MARCHE
•ARRÊT/
ON•OFF/
Power Adapter * Spec
Input: 120V~60Hz
Output: 5.9V 3A
Wattage: 17.7W
A
I
PQRSTUV W X
JK L M N O
B C D E F G H
FCC ID:2BEA3-24386
IC:10335A-24386
MODEL: HAL-24386

WWW.HOMEDEPOT.COM
Please contact 1-855-434-6543 (1-855-HD-HOLIDAY) for further assistance.
5
Assembly
1Placing the feet
□
2 Attaching the lower
support poles
□
NOTE: Throughout the instructions, Right and Left are
relative to the character. Hex wrench included for assembly.
3 Placing the shins
□
4 Attaching the upper
support poles
□
FRONT FRONT
BACK
BACK
RIGHT
RIGHT
LEFT
LEFT
Locking Pin
Means It's
Locked
Click
Place the Right Foot (B) and Left Foot (C) onto their
corresponding pole on the Base (A).
Slide the Right Shin (F) over the Right Lower Support Pole
(D) and slide the Left Shin (G) over the Left Lower Support
Pole (E).
Attach an Upper Support Pole (H) to both the Right Lower
Support Pole (D) and the Left Lower Support Pole (E).
Connect the Right Lower Support Pole
(D) and the Left Lower Support Pole (E)
to their corresponding pole available on
the Base (A).
NOTE: The Right Shin (F) and Left Shin (G) are designed to
only fit onto their corresponding Right Foot (D) and Left Foot (E).
B
C
A
F
DE
G
H
D
FG
E
H
A
D E

6
Assembly (continued)
5Placing the femurs
□
6 Attaching the pelvis
□
Slide the Right Femur (I) over the Upper Support Pole (H)
on the right side and fit onto the Right Shin (F). Slide the
Left Femur (J) onto the Upper Support Pole (H) on the left
side and fit onto the Left Shin (G).
Attach the Pelvis (K) to the Upper Support Poles (H) and fit
onto the Right Femur (I) and Left Femur (J).
NOTE: The Right Femur (I) and Left Femur (J) are designed to
only fit onto their corresponding Right Shin (F) and Left Shin (G).
NOTE: A ladder and more than 2 people are advised when
assembling the Pelvis (K) to the Upper Support Poles (H), Right
Femur (I), and Left Femur (J). If there is difficulty in assembling
the Pelvis (K), try adjusting the upper legs until they are
properly aligned.
NOTE: If connecting the Pelvis (K) is difficult, try attaching the
Pelvis (K) to the Upper Support Poles (H) in a lowered position.
Once the Upper Support Poles (H) are inserted, carefully raise
the assembly to a vertical position to help lock pins into place.
FG
HH
K
J I
K
H
I J

WWW.HOMEDEPOT.COM
Please contact 1-855-434-6543 (1-855-HD-HOLIDAY) for further assistance.
7
Assembly (continued)
7Laying down the assembly
□Lean the assembly onto the box it came in for easier assembly.
8 Attaching the spinal support
□Attach the Spinal Support (L) to the top of the Pelvis (K).
Outer box
NOTE: 3 adults are strongly recommended for this step.
K L

8
Assembly (continued)
9Attaching the rib cage
□10 Securing the loop screw
□
11 Attaching the right humerus
□
NOTE: After connecting the wires, hide the excess inside
the available cavity at the bottom of the Rib Cage (M).
NOTE: When connecting cables,
ensure that the arrow indicators on
each cable end are lined up with
and pointing at each other. There is
also a groove and a rod like
protrusion by these arrows that fit
into each other. Then firmly press
the cables together. Rotate the
cable cap clockwise onto the
threading of the corresponding
cable until firmly in place.
NOTE: Do not overtighten this screw. Overtightening may result in damage to the product.
If a screw is missing, check inside the box as it may have fallen out of the arm.
Slide the Rib Cage (M) over the Spinal Support (L). Then
connect the cable from the Rib Cage (M) to its
corresponding cable from the Pelvis (K). Then fit the Rib
Cage (M) onto the Pelvis (K).
With the Screw access hole facing the grooves on the shoulder shaft, set the Right Upper Arm (N) onto the right shoulder of the
Rib Cage (M). Use the Hex Wrench to tighten the screw in place. Do not overtighten. Arm position should be adjusted only after
arms are attached with screw facing grooves.
Grooves
Screw the Loop Screw (T) into the threading available in
the hole at the upper back of the Rib Cage (M).
Screw
M8*18mm
K
L
M
M
T
M
M
M
N
N

WWW.HOMEDEPOT.COM
Please contact 1-855-434-6543 (1-855-HD-HOLIDAY) for further assistance.
9
Assembly (continued)
12 Attaching the left humerus
□
13 Attaching the forearms
Set the Left Upper Arm (O) onto the left shoulder area of the Rib Cage
(M) so that the screw lines up with the grooves at the shoulder. Use a
Hex Wrench to tighten the screw in place.
□Connect the Right Forearm (P) to the Right Upper Arm (N) by using an insert and twist motion. Connect the Left Forearm (Q) to the
Left Upper Arm (O) by using an insert and twist motion. Arms can now be posed by raising or lowering. Follow cautions in Step 20.
Grooves
O
O
Q
p
O
O
M
M
M
N
N

10
Assembly (continued)
14 Securing the tether cable
□
15 Attaching the head
□
CAUTION: Cable may
have sharp ends, use
caution when assembling.
If cable cannot reach, the
upper body of the 12ft Giant
Sized Skelly needs to be
lifted while in its laying
position. This should enable
the cable to reach.
NOTE: The red cable is for
future accessories for the 12ft
Giant Sized Skelly. This red
cable does not have a use
otherwise and can be tucked
into the cavity at the top of the
Rib Cage (M).
Cable pairs are
color-coded to
ensure proper
color-matching
connections.
Set the Tether Cable (U) onto the hook available at the right side of the Base (A) and then thread the Tether Cable (U)
through the Loop Screw (T). Then set the other end of the Tether Cable onto the hook available at the left side of the
Base (A).
Connect the cables from the bottom of the Head (R) to their corresponding cables available at the top of the Rib Cage
(M). Tuck the excess cables into the cavity available at the top of the Rib Cage (M) and secure the Head (R) onto the Rib
Cage (M) using an insert and twist motion.
A
UU
M
M
M
R
R
R
T

WWW.HOMEDEPOT.COM
Please contact 1-855-434-6543 (1-855-HD-HOLIDAY) for further assistance.
11
Assembly (continued)
16 Plugging in the adapter
□
NOTE: When plugging the adapter into the 12ft Giant Sized
Skelly, ensure that the cap on the adapter cable is rotated
clockwise until firmly in place as shown.
17 Standing up the skeleton
□
CAUTION: The Tether Cable (U) must be secured before standing up the 12ft Giant Sized Skelly. It is strongly advised that
3 adults participate in the assembly, standing the skeleton up, setting the skeleton down, and disassembly. The item must
be laid down for disassembly.
ADAPTER
K
Plug the Adapter (W) into the adapter receiver available on
Control Panel or underside of the Pelvis (K).
Stand the assembly up with one person pressing down on the back of the Base (A) and another person lifting up by the
Rib Cage (M).
Control Panel
K
A
M
W

12
Assembly (continued)
18 Attaching the base extensions
□
19 Securing the base
□
NOTE: If your application requires additional stability,
add weights on top of the base (for example sand bags –
not included). You can also add guy wires (not included)
for added stability.
Attach the Base Extensions (S) to each corner of the Base (A).
If the Skeleton is assembled on soft ground, insert
the Stakes (V) through the holes and into the
ground at each corner of the Base (A).
S
VV
A
VA
V
V
S S
S
A

WWW.HOMEDEPOT.COM
Please contact 1-855-434-6543 (1-855-HD-HOLIDAY) for further assistance.
13
Assembly (continued)
20 Adjusting to preference
□
NOTE: The arms can be raised
or lowered to your preference.
Apply firm steady pressure on
the upper arm.
Do not apply pressure at the
hand or forearm to adjust arm
height, this may damage the
parts.
Loud 'clacking' is normal as the
arm moves. If you're unable to
move the arm, please contact
customer service for further
instructions.
Please pose arms before
standing up, otherwise a ladder
will be needed.
If you would like to add
additional lighting fun to your
skeleton, check out the 12 Foot
Skeleton Lighting Kit at The
Home Depot (sold separately).
IR SENSOR
Be sure nothing is
blocking the sensor.
The controls for turning on the LCD Eyes and toggling between the eye options are under the Pelvis (K). The Remote Control
(X) can also be used to change settings. Position the 12ft Giant Sized Skelly on flat surfaces only.
Your 12ft Giant Sized Skelly is now fully assembled. Plug in and turn on to let the fun begin!

14
Operation
1Controls
□
OPERATION INSTRUCTIONS
- CONTROL BOX:
Plug the power adapter into a standard power
outlet. Locate the 2 push buttons on the control
panel underneath the Pelvis (K). Middle Button is
for ON/OFF and Sensor/Timer. Button at corner
of panel is to select from 8 Eye options/modes.
NOTE: The 12ft Giant Sized Skelly is compatible with external timers and preserves its setting when the power is turned OFF/ON.
NOTE: The 12ft Giant Sized Skelly has 3
different function settings (ON, SENSOR/TIMER
and OFF) and 8 different Eye Options (MODES) to
chose from - see images on box.
Settings and Eye options can be controlled at the
Control Panel or by using the Remote Control.
Timer/Sensor setting is only available on the
Skeleton Control Panel, located on the underside
of the Pelvis (K). 5.9V









This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Cet appareil est conforme à la section 15 des
règlements de la FCC. Le fonctionnement est
sujet aux deux conditions suivantes : (1) Cet
appareil ne doit pas émettre d'interférences
dangereuses, et (2) cet appareil doit être en
mesure d'accepter toutes les interférences reçues
incluant celles qui peuvent provoquer un mauvais
fonctionnement.
Este dispositivo cumple con la Parte 15 de las
Reglas FCC. El manejo está sujeto a las siguientes
dos condiciones: (1) este dispositivo no debe
causar interferencias dañinas, y (2) este
dispositivo debe aceptar cualquier interferencia
recibida, incluyendo las interferencias que pueden
causar un funcionamiento indeseado.
© Seasonal Visions International Limited
All Rights Reserved
Tous droits réservés
Reservados todos derechos
CAN ICES-003(B)/NMB-003(B)
MODE/
MODE/
MODO



Made in China
Fabriqué en Chine
Hecho en China
1
4
2
3
Button Function Description
LIGHTS ONLY /
ÉCLAIRAGE UNIQUEMENT /
SÓLO LUCES
TIMER • SENSOR /
MINUTEUR • DÉTECTEUR /
TEMPORIZADOR • SENSOR
OFF • STEP PAD /
ARRÊT • TAPIS ÉLECTRONIQUE /
APAGAR • ALMOHADILLA DE PASO
Press middle button once to activate the LCD eyes indefinitely until the
settings are changed.
Press middle button twice to activate the LCD eyes for an 18 second
function cycle when the Infra-red (IR) sensor is activated. The Infra-red
(IR) sensor has a range of up to 4 m/13 ft. and will activate when
someone comes within an 80-degree angle from left to right as well as
from above and below.
Press middle button a third time to turn LCD eyes OFF, or if using the Step
Pad for activation, each press activates the 12ft Giant Sized Skelly for an
18 second cycle.
Corner button toggles through 8 LCD eye options.
MODE/
MODE/
MODO
1
2
3
4

WWW.HOMEDEPOT.COM
Please contact 1-855-434-6543 (1-855-HD-HOLIDAY) for further assistance.
15
Operation (continued)
2Remote control
MODE/
MODE/
MODO
ENCENDER
•APAGAR
MARCHE
•ARRÊT/
ON•OFF/
1.5V AAA
1.5V AAA
This Remote Control allows one to change the settings of the 12ft Giant Sized Skelly from up to
20 ft away. The Remote Control has an indicator light that lets you know if its working.
NOTE: Requires 2 x 1.5V AAA batteries (Included)
* You will need a small Phillips head screwdriver（Not included ).
Locate the battery compartment on the product. Remove the battery compartment cover by using a small Phillips head screwdriver to unscrew
the screw. After removing or installing the batteries, place the battery compartment cover into position, and secure the battery cover. If Skeleton
is being stored while not in use, please remove battery in Remote Control.
NOTE: Timer/Sensor setting can only be chosen from the Skeleton Control Panel, not with Remote Control.
1 2
Button Function Description
ON • OFF /
MARCHE • ARRÊT /
ENCENDER •APAGAR
This button turns the Skeleton on and off.
This button toggles through the 8 different LCD eye displays for the 12ft
Giant Sized Skelly.
MODE/
MODE/
MODO
1
2
FCC ID:2BEA3-24386
IC:10335A-24386
MODEL: HAL-24386

16
Care and Cleaning
□General Cleaning
□Power Adapter Spec
□Wipe with a clean, damp cloth. If packing, allow 12ft Giant Sized Skelly to fully dry before putting back in the box.
Troubleshooting
Problem Solution
NOTE: When not in use, store this product in its original packing. Keep away from heat and
moisture. Remove batteries from Remote Control.
The LCD eyes are not lighting up or are not functioning properly
(cannot switch between eye options).
The item does not turn on when activated.
The Remote Control is not working.
Ensure that all cables are firmly connected to their corresponding
cables. Make sure that the adapter is plugged into a live outlet and
that the adapter is plugged firmly into the adapter receiver. If the
issue persists, contact customer service.
Make sure that the adapter is plugged into a live outlet. Also make
sure that the adapter is firmly plugged into the adapter receiver. If
the issue persists, contact customer service.
Make sure you are withing a 20 ft. range of the 12ft Giant Sized
Skelly. If the issue persists, replace the batteries in the Remote
Contro with fresh batteries (2 x 1.5V AAA). If there is still a problem
with your Remote Control, contact customer service.
The sensor is not working. Make sure the sensor is not aimed at an area that is either a heat
source or any drafty areas. The Infra-red sensor works by detecting
changes in temperature and these environments can affect its
function. Make sure nothing is blocking the sensor and that the
sensor cable is firmly plugged into its corresponding cable. If the
issue persists, please contact customer service.
Service Parts
Replacement parts are available for most parts listed on page 4, but supplies are limited and restrictions do apply. Additional parts
(wiring, hardware, etc.) may also be available.
Please retain your receipt or proof of purchase from The Home Depot.
Contact Customer Support for details or if you have any question about assembly or operation. Contact information is at the front and
back of this manual.
Input:
Output:
Wattage:
120V~60Hz
5.9V 3A
17.7 W

Retain this manual for future use.
1-855-HD-HOLIDAY (1-855-434-6543)
HOMEDEPOT.COM
Questions, problems, missing parts? Before returning to the store, call Home Accents Holiday
Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday