Home Automation Omni Pro II User manual

HOME AUTOMATION, INC.
Control & Security System
Includes the SIA CP-01 Control Panel Standard
Features for False Alarm Reduction
Installation Manual
Document Number 20I00-2 Rev. 3.2
August, 2009

Home Automation, Inc.
Installation Manual
Includes the SIA CP-01 Control Panel Standard
Features for False Alarm Reduction
Document Number 20I00-2 Rev. 3.2
August, 2009
Copyright © 2001-2009 Home Automation, Inc.
All Rights Reserved

CONTENTS
INTRODUCTION........................................................................................................................................... 1
PLANNING .......................................................................................................................................................................................1
INSTALLATION............................................................................................................................................ 2
CONTROLLER HOOKUP .............................................................................................................................................................2
ABOUT SECURITY ZONES ..........................................................................................................................................................4
BURGLAR ZONE HOOKUPS ..................................................................................................................................................4
ABOUT FIRE ZONES .....................................................................................................................................................................5
TWO-WIRE SMOKE DETECTORS.........................................................................................................................................6
FOUR-WIRE SMOKE DETECTORS .......................................................................................................................................6
TELEPHONE CONNECTIONS .....................................................................................................................................................9
DIGITAL SUBSCRIBER LINE (DSL) CONNECTIONS.........................................................................................................9
LCD CONSOLE HOOKUP...........................................................................................................................................................11
CONSOLE SETUP .........................................................................................................................................................................12
CONSOLE ADDRESS.............................................................................................................................................................12
SOUNDER................................................................................................................................................................................12
KEY CLICK .............................................................................................................................................................................12
KEY BACKLIGHT ..................................................................................................................................................................12
VIEWING ADJUSTMENT......................................................................................................................................................12
LANGUAGE ............................................................................................................................................................................12
EXIT SETUP MODE ...............................................................................................................................................................12
SOUNDER OUTPUTS ...................................................................................................................................................................14
INTERIOR SOUNDER HOOKUP...........................................................................................................................................14
EXTERIOR SOUNDER HOOKUP .........................................................................................................................................14
CONTROLLER OUTPUTS ..........................................................................................................................................................16
RESET OUTPUTS .........................................................................................................................................................................16
OUTPUT APPLICATIONS...........................................................................................................................................................16
GENERAL PURPOSE SWITCHING APPLICATIONS.........................................................................................................16
SOUNDER TRIGGERING ......................................................................................................................................................16
COMMUNICATOR OUTPUTS ..............................................................................................................................................17
"ARMED" AND "OK TO ARM".............................................................................................................................................17
SWITCHED OUTPUT .............................................................................................................................................................17
HAI COMMUNICATING THERMOSTATS..........................................................................................................................17
REMOTE ARM/DISARM SWITCH............................................................................................................................................17
HAI THERMOSTATS ...................................................................................................................................................................19
PROGRAMMABLE ENERGY SAVER MODULES .................................................................................................................20
TEMPERATURE, OUTDOOR TEMPERATURE, AND HUMIDITY ....................................................................................21
BUILT-IN SERIAL PORTS ..........................................................................................................................................................23
BUILT-IN ETHERNET PORT .....................................................................................................................................................24
CONTROLLER IP ADDRESS, PORT NUMBER, AND ENCRYPTION KEY.....................................................................24
CONTROLLER IP ADDRESS ................................................................................................................................................25
CONTROLLER PORT NUMBER...........................................................................................................................................25
ENCRYPTION KEY ................................................................................................................................................................25
OMNIPRO II ETHERNET CONNECTIONS..........................................................................................................................25
CONNECTING TO NETWORK VIA PC ACCESS................................................................................................................26
SYSTEM POWER UP PROCEDURE ....................................................................................................... 28
CONSOLE CHECK OUT..............................................................................................................................................................28
TELEPHONE CHECK OUT ........................................................................................................................................................28
BURGLAR ZONE CHECK OUT .................................................................................................................................................29
FIRE ZONE CHECK OUT ...........................................................................................................................................................29
CUSTOMER CHECKOUT ...........................................................................................................................................................29
IN CASE OF TROUBLE ...............................................................................................................................................................30
CONSOLES..............................................................................................................................................................................30
CONTROLLER ........................................................................................................................................................................30

DIGITAL COMMUNICATOR................................................................................................................... 32
DESCRIPTION OF CONTACT ID..............................................................................................................................................32
DESCRIPTION OF 4/2 FORMAT ...............................................................................................................................................33
3/1 FORMAT ..................................................................................................................................................................................33
OPENING AND CLOSING REPORTS.......................................................................................................................................33
INSTALLER SETUP.................................................................................................................................... 34
SETUP CONTROL ........................................................................................................................................................................34
X-10 HOUSE CODE................................................................................................................................................................34
UPB NETWORK ID ................................................................................................................................................................ 34
X-10 3-PHASE .........................................................................................................................................................................35
OUTPUT TYPES .....................................................................................................................................................................35
Z-WAVE NODE ID .................................................................................................................................................................36
SETUP ZONES............................................................................................................................................................................... 37
ZONE EXPANSION ................................................................................................................................................................37
ZONE RESISTORS..................................................................................................................................................................37
ZONE TYPES ..........................................................................................................................................................................38
LATCHING ZONE TYPES .....................................................................................................................................................38
DESCRIPTION OF ZONE TYPES..........................................................................................................................................39
SETUP DIGITAL COMMUNICATOR .......................................................................................................................................42
FIRST PHONE NUMBER, FIRST ACCOUNT NUMBER ....................................................................................................42
COMMUNICATOR TYPE ......................................................................................................................................................42
TWO-WAY AUDIO.................................................................................................................................................................42
REPORT OPEN/CLOSE..........................................................................................................................................................43
REPORT BYPASS / RESTORE ..............................................................................................................................................43
AUTOMATIC TEST TIME ..................................................................................................................................................... 43
ALARM CODES (4/2 and 3/1 Formats) ..................................................................................................................................43
SETUP AREAS............................................................................................................................................................................... 44
SETUP AREAS: CONTROL ...................................................................................................................................................44
SETUP AREAS: ZONES .........................................................................................................................................................46
SETUP AREAS: BUTTONS....................................................................................................................................................46
SETUP AREAS: CONSOLES .................................................................................................................................................46
SET-UP AREAS: THERMOSTATS........................................................................................................................................47
SETUP AREAS: MESSAGES ................................................................................................................................................47
SETUP TEMPERATURES ...........................................................................................................................................................48
TEMPERATURE DISPLAY....................................................................................................................................................48
THERMOSTAT TYPE.............................................................................................................................................................48
Z-WAVE THERMOSTAT NODE ID......................................................................................................................................48
SETUP MISCELLANEOUS .........................................................................................................................................................49
INSTALLER CODE.................................................................................................................................................................49
ENABLE PC ACCESS.............................................................................................................................................................49
PC ACCESS CODE..................................................................................................................................................................49
CALL BACK PHONE NUMBER............................................................................................................................................49
OUTSIDE SIREN DELAY ......................................................................................................................................................49
DIAL OUT DELAY .................................................................................................................................................................50
ALARM RESET TIME ............................................................................................................................................................50
ARMING CONFIRMATION................................................................................................................................................... 50
FIRE ALARM VERIFICATION .............................................................................................................................................50
SUPERVISE INT SNDR..........................................................................................................................................................51
SUPERVISE EXT SNDR.........................................................................................................................................................51
ENABLE EMERGENCY KEYS .............................................................................................................................................51
TIME DISPLAY.......................................................................................................................................................................51
DATE DISPLAY......................................................................................................................................................................51
AC POWER FREQUENCY.....................................................................................................................................................51
DEAD LINE DETECT.............................................................................................................................................................52
OFF HOOK DETECT ..............................................................................................................................................................52
PICKUP AFTER HANGUP..................................................................................................................................................... 52
CLOCK ADJUSTMENT.......................................................................................................................................................... 52
MODEL AND SOFTWARE VERSION..................................................................................................................................52

RESET SYSTEM EEPROM ....................................................................................................................................................52
RESET SYSTEM RAM............................................................................................................................................................53
ETHERNET MAC ADDRESS.................................................................................................................................................53
SETUP EXPANSION .....................................................................................................................................................................53
MODULE 1 TYPE ...................................................................................................................................................................53
MODULE 2 TYPE - MODULE 4 TYPE .................................................................................................................................54
SERIAL 1 RATE ......................................................................................................................................................................54
SERIAL 1 FUNCTION ............................................................................................................................................................54
SERIAL 2 - SERIAL 5 RATE..................................................................................................................................................54
SERIAL 2 FUNCTION ............................................................................................................................................................54
SERIAL 3 FUNCTION ............................................................................................................................................................55
SERIAL 4 - SERIAL 5 FUNCTION ........................................................................................................................................55
SERIAL 6 RATE ......................................................................................................................................................................55
SETUP ZONE OPTIONS ..............................................................................................................................................................56
SWINGER SHUTDOWN NUMBER.......................................................................................................................................56
CROSS ZONE WINDOW........................................................................................................................................................56
ZONE 1 OPTIONS – ZONE 176 OPTIONS............................................................................................................................56
SIA CP-01 COMPLIANCE ......................................................................................................................... 57
Minimum Equipment Requirements for a CP-01 Compliant Installation: ...............................................................................57
OMNIPRO II SPECIFICATIONS.............................................................................................................. 58
UNDERWRITER'S LABORATORIES (UL) INSTALLATION REQUIREMENTS .......................... 59
24-HOUR STANDBY BATTERY CAPACITY......................................................................................... 60
SMOKE DETECTOR INSTALLATION GUIDELINES ........................................................................ 61
APPENDIX A – CONTACT ID REPORTING FORMAT....................................................................... 62
APPENDIX B - DIGITAL COMMUNICATOR CODE SHEET ............................................................ 63
APPENDIX C - ZONE AND UNIT MAPPING ........................................................................................ 68
APPENDIX D – FIRMWARE UPDATES ................................................................................................. 69
FIGURES
FIGURE 1 - CONTROLLER HOOKUP............................................................................................................................................3
FIGURE 2 - OVERALL CONNECTIONS DIAGRAM ....................................................................................................................5
FIGURE 3 - TWO-WIRE FIRE ZONE CONNECTIONS .................................................................................................................7
FIGURE 4 - FOUR-WIRE FIRE ZONE CONNECTIONS ...............................................................................................................8
FIGURE 5 - RJ31X JACK CONNECTIONS...................................................................................................................................10
FIGURE 6 – DSL SPLITTER CONNECTIONS .............................................................................................................................11
FIGURE 7 - CONSOLE CONNECTIONS ......................................................................................................................................13
FIGURE 8 - SOUNDER CONNECTIONS......................................................................................................................................15
FIGURE 9 - RESETTING CONTROLLER OUTPUTS..................................................................................................................16
FIGURE 10 - REMOTE KEYSWITCH CONNECTIONS..............................................................................................................18
FIGURE 11 - HAI THERMOSTAT CONNECTIONS....................................................................................................................19
FIGURE 12 - TEMPERATURE / HUMIDITY SENSOR CONNECTIONS ..................................................................................21
FIGURE 13 - PESM CONNECTIONS ............................................................................................................................................22
FIGURE 14 - RS-232 CONNECTIONS...........................................................................................................................................23
FIGURE 15 - RS-485 CONNECTIONS...........................................................................................................................................24
FIGURE 16 - LOCAL NETWORK..................................................................................................................................................26
FIGURE 17 - LOCAL / WIDE AREA NETWORK ........................................................................................................................27
FIGURE 18 - 24-HOUR STANDBY CONNECTIONS ..................................................................................................................60

Page 1
INTRODUCTION
This installation guide is intended as an aid to installing the OmniPro II Control & Security System. The installer should also
have thoroughly reviewed and understood the OmniPro II Owner's Manual, which has important information regarding final setup
of the system. This manual assumes that the installer has a basic understanding of installing a security system.
This guide applies to the 20A00-2, -5, and -22 versions of the OmniPro II series controller. Refer to the Underwriters
Laboratories Installation Requirements section for details in the application of each. Failure to install the OmniPro II and its
accessories in accordance with the UL Requirements in this manual and in the Owner's Manual, is a violation of the Listing Mark.
PLANNING
Before you start, your system should be planned as follows:
1. Zones:
•Decide where each contact or detector will be located
•Decide which zone it will occupy
•Decide zone type for each zone
•Decide which area it will occupy
•With the customer, decide what text and voice descriptors will be used. Consult table of voice descriptors, so that you
can choose similar words for the text to avoid customer confusion.
•See SMOKE DETECTOR INSTALLATION GUIDELINES to plan locations for smoke detectors
2. Consoles:
•Consult the customer on the console location. The console should be easily accessible.
3. Interior Sounder and Outside Siren:
•Locate both where they cannot be tampered with.
4. Lighting and Appliance Switches and Modules.
5. Plan for thermostats, energy saver modules, or other options.
6. Give consideration to where the controller will go. Remember that it needs a duplex receptacle not controlled by a switch,
preferably on its own circuit, within 5 feet of the controller.

Page 2
INSTALLATION
Go over your plan with your customer.
1. Install the entire system. Refer to sections in this manual to see how to install various components.
2. Follow the Power-Up and Checkout procedures.
3. Explain the basics to the customer. Deliver all manuals and documentation.
4. Follow up with your customer to keep them satisfied.
CONTROLLER HOOKUP
1. When choosing a place to mount the controller, consider the following:
a. A duplex outlet, preferably on its own circuit, is required to be within 5 feet of the controller for the power transformer and
the UPB PIM or X-10 Interface Module.
b. The controller should be protected from weather, temperature extremes, and burglars.
2. GROUND THE CONTROLLER "EARTH GND" TERMINAL TO A COLD WATER PIPE OR TO A 4-FOOT GROUND
ROD TO PRESERVE ITS BUILT-IN TRANSIENT PROTECTION. USE 14 GAUGE WIRE. TRANSIENT
PROTECTION WILL NOT WORK IF THE CONTROLLER IS NOT PROPERLY GROUNDED.
3. Connect the 24 VAC power transformer to the 24 VAC INPUT terminals.
4. Connect the BLACK battery wire to the minus (-) terminal on the battery. DO NOT connect the red wire at this time. DO
NOT reverse the connections; the battery fuse will blow. Note that the unit will NOT START on the battery alone.
5. Connect the Powerline Interface Module to the OmniPro II controller:
a) UPB PIM (P/N: 36A00-1): Plug one end of the 6-conductor modular cable into the connector marked “J3” (SERIAL 3)
on the OmniPro II controller and plug the other end into the modular connector on the PIM.
b) X-10 Interface Module (P/N: TW523): Plug one end of the 4-conductor modular cable into the connector marked “J7”
(X-10) on the OmniPro II controller and plug the other end into the modular connector on the X-10 Interface Module.
6. Refer to FIGURE 1 (CONTROLLER HOOKUP) for this configuration.

Page 3
YUASA NP7-12
OR EQUIVALENT
BLACK WIRE TO -
RED WIRE TO +
12V 7AH
BATTERY
ELECTRIC CODE, ANSI/NFPA 70.
ACCORDANCE WITH THE NATIONAL
GOUNDING METHOD MUST BE IN
OR GROUND ROD
COLD WATER PIPE
14 GA. WIRE
OR EQUIVALENT
MODEL RT-2440SL
REVERE
24 VAC 40 VA
POWER TRANSFORMER
WIRING IN THE ENCLOSURE
ALL OTHER POWER LIMITED/CLASS II
MUST BE SEPERATED FROM
LIMITED. THE BATTERY LEADS
THE BATTERY IS NON-POWER
BY AT LEAST 1/4"
SPACING
1/4"
6 CONDUCTOR
Powerline Interface Module
Status
<Program
UPB™
FIGURE 1 - CONTROLLER HOOKUP

Page 4
ABOUT SECURITY ZONES
Each of the 176 security zone inputs on an OmniPro II system may be configured as a burglary zone, a fire zone, a temperature
zone, or an auxiliary input. Zones 1-4, however, are the only inputs that can be used with 2-wire smoke detectors. Zones 9-16
(on the controller) and Zones 49-176 (on expansion enclosures) are the only inputs that can be configured as a PESM.
An external 1000-ohm end-of-line zone resistor is required for all zones unless the Setup item ZONE RESISTERS is set to "No".
If the Setup item ZONE RESISTORS is disabled, all zones other than Supervised Fire and Gas (and all zone inputs on Expansion
Enclosures) will not use an end-of-line resistor. In this configuration, all zone switches (other than Supervised Fire and Gas) must
be normally closed (open for alarm). If any zone requires a normally open (closed for alarm) switch (other than Supervised Fire
and Gas), the Setup item ZONE RESISTORS must be set to "Yes" and all zones will require and external 1000-ohm end-of-line
resistor.
The zone type for each zone is selected through the INSTALLER SETUP menu or by using the PC ACCESS software.
The system supports a maximum zone resistance, excluding the end-of-line resistor, of 150 ohms. The default setting for ZONE
RESISTORS is "Yes". The default settings for all zone inputs on an OmniPro II controller are configured as Auxiliary inputs.
OmniPro II can be expanded to 176 zones by adding two 16 Zone Hardwire Expander Modules and up to eight 16 Zone
Expansion Enclosures or Wireless Receivers.
BURGLAR ZONE HOOKUPS
The OmniPro II system supports both normally open and normally closed switches. Most contacts designed for doors, windows,
motion detectors, glassbreak detectors and other security devices meet this requirement. An external 1000-ohm end-of-line
resistor must be used for all burglary zones if ZONE RESISTORS is set to "Yes".
1. When using a normally open switch, a 1000-ohm end-of-line resistor must be in parallel with the zone being used. Maximum
loop resistance excluding end-of-line resistor should not exceed 150 ohms. ZONE RESISTORS must be set to "Yes".
2. When using a normally closed switch, a 1000-ohm end-of-line resistor must be put in series with the zone being used if
ZONE RESISTORS are set to "Yes". If ZONE RESISTORS are set to "No", the 1000-ohm end-of-line resistor is not used.
Maximum loop resistance excluding end-of-line resistor should not exceed 150 ohms.
Note: The 1000-ohm end-of-line resistor is required on all zone inputs on Expansion Enclosures.
3. Power motion detectors from AUXILIARY 12V.
4. Unused zones may be left open, and should be left at the default setting of AUXILIARY zone types.
5. When Zones 1-4 are configured to anything other than a Supervised Fire or Gas zone, the corresponding Zone Jumpers
(JP11-JP14) must be in the NRM (normal) position.
6. See FIGURE 2 (OVERALL CONNECTIONS DIAGRAM) for configurations of burglary zones.