Home Decorators Collection MARTHA STEWART WSMSL-SKW User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Whalen Storage Factory No.: 15548 Page #1 of 9
MARTHA STEWART LIVING CLOSET STARTER
TOWER W/SHELF ANTIQUE WHITE / NATURAL
Assembly Instructions
HDC #:2944300410/2944300950
MFG #:WSMSL-SKW&WSMSL-SKN
Please read over the instructions; it will be a
time-saver in the long run.
Note: Before Assembly, please be sure to work on a soft flat
surface to avoid any damage to the finish.

Please call for replacement parts or assistance:1-866-942-5362
Whalen Storage Factory No.: 15548 Page #2 of 9
ASSEMBLY TIPS
Read all instructions BEFORE assembly.
Remove all hardware from box and sort by size.
Check to see that all hardware and parts are present BEFORE assembling.
Ask a friend to assist you with the assembly of this furniture.
To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
Please wait until all steps are completed before tightening bolts.
Make sure all bolts are tightly fastened before the unit is used.
This unit is intended for use only with the maximum weights
indicated. Use with products heavier than the maximum weights indicated may
result in instability causing possible injury.
MAXIMUM RECOMMENDED WEIGHT LOADS
SHELF & BOTTOM
MAXIMUM LOAD: 30 LBS. (13.6KG)

Please call for replacement parts or assistance:1-866-942-5362
Whalen Storage Factory No.: 15548 Page #3 of 9
Important
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat
and non-abrasive surface. You will need the parts identified on page 3 and 4 of this instruction
manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE
WIPED OFF WITH DAMP CLOTH.
Insert Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together;
making sure Cam Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the
face of Cam Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.
You are now ready to assemble the KD unit.
XX
FINAL
1 2 43

Please call for replacement parts or assistance:1-866-942-5362
Whalen Storage Factory No.: 15548 Page #4 of 9
Parts List
Please read completely through the instructions and verify that all parts listed are present before
beginning assembly.
A-Top Panel (x 1) B-Side Panel Left (x 1) C- Side Panel Right (x 1)
D- Shelf Panel (x 1) E- Bottom Panel (x 1) F- Stretcher (x 2) G- Back Panel (x 1)
Hardware List
Please read completely through the instructions and verify that all hardware listed are present
before beginning assembly.
1-Cam Lock (x 20+1 extra) 2- Cam Bolt (x 20+1 extra) 3- M8x30 mm Wood Dowel (x 20+1 extra)
4- M2x19 mm Pan Head Screw (x 34+1 extra) 5- Floor Protector (x 4) 6- Plastic Cover (x 8+1 extra)
7- Tipping Restraint Hardware (x 2) 8- Glue (x 1)
Tools required (not provided): Rubber mallet, Phillips screwdriver, Power drill

Please call for replacement parts or assistance:1-866-942-5362
Whalen Storage Factory No.: 15548 Page #5 of 9
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble
the unit on a carpeted floor or the empty carton to avoid any scratch.
2. Place the Bottom Panel (E), the Side Panel Left (B) and the Side Panel Right (C) on a
level and protective surface with the holes facing up. Securely screw the Cam Bolts (2)
into the designated small holes, as shown in the illustration.
3. Insert two Wood Dowels (3) into the inner end holes of Stretcher (F). Tap in with a mallet,
if necessary. Make sure you use a small amount of glue with both ends of all dowels.
NOTE: It is very important to use a small amount of glue on both ends of dowels.
4. Align the inserted Wood Dowels (3) on the Stretcher (F) with the drilled holes on the
Bottom Panel (E) and press them together. Make sure that the raw edge on the Stretcher
points towards the back of the unit and the Cam Lock holes will face inside. As shown
below. Fasten the Stretcher (F) to the Bottom Panel (E) by engaging 2 Cam Locks (1).
(Refer to page 3 on Cam Lock system operation supplement).
5. Repeat the same procedure to attach the other Stretcher (F) at the other end.
2
B
C
E
2
F
E
F
1
3
2

Please call for replacement parts or assistance:1-866-942-5362
Whalen Storage Factory No.: 15548 Page #6 of 9
Assembly Instructions
6. Insert Wood Dowels (3) into the inner end holes of Top Panel (A), Shelf Panel (D),
Stretcher (F) ,Bottom Panel (E) . Tap in with a mallet, if necessary. Make sure you use a
small amount of glue with both ends of all dowels.
NOTE: It is very important to use a small amount of glue on both ends of dowels.
7. Align the inserted Wood Dowels (3) on the Top Panel (A), Shelf Panel (D), Stretcher (F) ,
Bottom Panel (E) with the drilled holes on the Side Panel Left (B) and press them
together. Make sure that the raw edge on the Top Panel (A), Shelf Panel (D), Bottom
Panel (E), Side Panel Left (B) points towards the back of the unit and the Cam Lock
holes will face at the floor. As shown below. Fasten the Top Panel (A), Shelf Panel (D),
Stretcher (F), Bottom Panel (E) to the Side Panel Left (B) by engaging Cam Locks (1).
(Refer to page 3 on Cam Lock system operation supplement).
8. Repeat the same procedure to attach the Side Panel Right (C) at the other end.
9. Now, go back and tighten all Cam Locks and Screws. Make sure that all the parts are
tight and there are no gaps between the pieces. This will help keep the unit square.
1
1
3
B
A
D
E
C
F

Please call for replacement parts or assistance:1-866-942-5362
Whalen Storage Factory No.: 15548 Page #7 of 9
Assembly Instructions
10. Unfold the Back Panel (G) and lay it to the back edges of the assembled unit, as shown.
Make sure the overlaps on the panels are even all the way around. Secure the Back
Panel (G) in place using the M2x19 mm Pan Head Screw (4). We recommend attaching
the back panel with the screws at the corners first.
11. Gently tap the Floor Protectors (5) at the bottom of side panels avoiding crack or
damage of side panel.
12. Stand the assembled unit upright.
13. Plug Plastic Covers (6) to cover the visible Cam Locks inside the cabinet.
G
4
4
C
5
5
6
B

Please call for replacement parts or assistance:1-866-942-5362
Whalen Storage Factory No.: 15548 Page #8 of 9
Important Notice Please Read
Note: The unit is designed to combine with our other product at the same series as shown
below for your reference.
WSMSL-FSDKW
WSMSL-FSDKN
(Sold Separately)
WSMSL-HSDKW
WSMSL-HSDKN
(Sold Separately)
WSMSL-SS2W
WSMSL-SS2N
(Sold Separately)
WSMSL-FS2W
WSMSL-FS2N
(Sold Separately)
WSMSL-28PB
(Sold Separately)
WSMSL-V8CDW
WSMSL-V8CDN
(Sold Separately)
WSMSL-6CDW& WSMSL-FS2W
WSMSL-6CDN& WSMSL-FS2N
(Sold Separately)
WSMSL-8CDW& WSMSL-FS2W
WSMSL-8CDN& WSMSL-FS2N
(Sold Separately)
WSMSL-LHW
WSMSL-LHN
(Sold Separately)
WSMSL-4DCW
WSMSL-4DCN
(Sold Separately)
WSMSL-6DCW
WSMSL-6DCN
(Sold Separately)
WSMSL-HC3DW
WSMSL-HC3DN
(Sold Separately)
WSMSL-5DTCW
WSMSL-5DTCN
(Sold Separately)

Please call for replacement parts or assistance:1-866-942-5362
Whalen Storage Factory No.: 15548 Page #9 of 9
TIPPING RESTRAINT HARDWARE
We have included one Tipping Restraint Hardware bag (7) for this unit. You must install this hardware to
prevent accidents or injuries from falling unit.
When properly installed, this restraint can provide protection against the unexpected tipping of the storage
rack due to small tremors, bumps or climbing. We strongly recommended mounting this hardware to a
wall stud and your unit. Please carefully read the instructions printed on the bag.
Note: You must install the Tipping Restraint Hardware with the unit in use to prevent any accidents or
damage to the unit.
Tools Required: Phillips Screwdriver, Mallet, Power Drill, and 3/8” Drill Bit.
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting.
Use of furniture polishes is not necessary. Should you choose to use polishes, test in an
inconspicuous area first.
Using solvents of any kind on your furniture may damage the finish.
Never use water to clean your furniture as it may cause damage to the finish.
Always use coasters under beverage glasses and flowerpots.
Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid
rubbing.
Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may
create spotting within the furniture finish.
Stains or marks from crayons or ink markers will be difficult to remove.
In the event that your furniture is stained or otherwise damaged during use, we recommend that you
call a professional to repair your furniture.
Check bolts/screws periodically and tighten them if necessary.
Further advice about wood furniture care
It is best to keep your furniture in a climate controlled environment. Extreme temperature and
humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep
furniture away from direct sunlight as may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Follow the important and
helpful tips that will enhance your furniture as it ages.
We hope you enjoy your purchase for many years.
Thank you for your purchase.