Home Decorators Collection 1002099636 User manual

Page 1
1 Light Exterior Wall Lantern with Motion Sensor
Home Depot SKU 1002099636 (UPC 718212222119)
(Oil Rubbed Chestnut Finish)
INSTRUCTION MANUAL

Page 2
Thank you for purchasing this Home Decorators Collection exterior wall lantern.
This product has been manufactured with the highest standards of safety and
quality. The finish of this lantern is weather resistant but over time will naturally
weather and fade.
WARNING: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FEATURES:
1. MOTION SENSOR FUNCTION-The motion sensor activates at dusk and automatically turns the
light on when it detects a moving heat source such as people and vehicles are within its coverage
area. The motion sensor will remain active throughout the night and deactivate at dawn.
(Note: When power is first applied, the light will come on for about 20 sec. to allow the electrical
current to stabilize. Once stable the software in the Motion Sensor’s Test Mode and Auto Mode
functions can be carried. The sensor has 2 knobs one is to adjust the sensitivity and the second is a
shut off delay timer. (See fig.1) The motion sensor should be turned as Fig.2 to adjust the knobs
location from the back to the side for accessibility when needed to adjust the settings.)
TEST MODE AUTO MODE
Works at Day & Night Night only
Activated by Motions Motions
On time As motion existing As motion existing
Shut-off delay time 5Sec. 10Sec.～10Min.
1' 5'
10'
TIMER
13Ft
5Ft
21Ft
30Ft
Auto
Test
SENSITIVITY
Light Cap rotates to the right for easy
access to motion sensor settings
Fig.2
TURN
Fig.1

Page 3
2. Manual Override Mode (auto rest at dawn)
During night, by switching off the wall
switch for 2 seconds and then on again,
the light will be turned on to dawn. To
return to Auto Mode, simply switch the
power off and switch on again in the
same manner.
3. Uses medium-based incandescent light bulb.
SPECIFICATIONS:
1. Motion Sensor Range: Up to 30 ft (Varies with surrounding temperature).
2. Sensor Detection Angle: 220º.
Testing and Setting:
1. If installed at a height of 6.5′, the lantern will provide a
detection distance up to 30′ (See fig.4). The sensitivity
increases win cooler temperatures you may wish to make adjustment as seasons change.
2. The sensor is more sensitive to movements across its detection path rather than the movements
towards it directly. Walk at normal speeds across the detection area to set the desired detection
distance properly.
3. During Test Mode, the light will come ON for 5 sec. every time when movement is detected. Set
the Shut-off Delay Timer only when the light is in the Auto Mode.
4. Clean the sensor lens with soft cloth every 1 or 2 month to dust the sensor from less sensitivity.
Sensitivity:
1. The sensitivity was set at the maximum by the factory. By turning the knob in counterclockwise, the
detection distance can be decreased to the minimum of 5’.
2. The detection range can reach the coverage of 220 degrees (approx.).
Shut-off Delay time:
During Auto Mode, the light will stay ON as long as motion is detected. When no movement is
detected, the light will turn OFF after the delay time has elapsed. The time is 10 sec at the minimum;
By turning the knob in clockwise, it will increased the time up to 10 min. as the maximum.
SELECTING A LOCATION:
1. When selecting a location, be aware that the motion sensor is more sensitive to movement across
its coverage area and less sensitive to movement toward or away from the motion sensor. (Fig 5)
Fig.3
Manual Override O
p
eratin
g
Turn wall switch
OFF-ON within 2 sec
Auto
Mode
Manual
Override
Mode
Turn wall switch OFF-ON
within 2sec.or reset
automatically at dawn
Fig.4

Page 4
SELECTING A LOCATION (CONTINUED):
2. Select locations away from nighttime light sources, such as street lamps or other light fixtures. They
may shine light onto the fixture’s photocell sensor. This light might cause the circuit to “think” that
it is daytime and not allow the fixture’s functions to operate.
3. Be aware that shade from a porch or an eave may not allow enough daylight to shine onto the
motion sensor and may cause the circuit to “think” that it is nighttime, and subsequently cause the
light to come on during the daytime.
4. Be aware that motorized equipment, such as power tools, on the same electrical circuit may cause
oscillations on the electrical line which might cause the fixture to malfunction.
5. Select locations away from heat sources, such as heating vents, air conditioners, and heated
swimming pools.
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local Home Depot, please call our Customer Service Team at 1-
800-986-3460 or visit HOMEDEPOT.COM/HOMEDECORATORS.
Please reference your SKU 1002099636 Oil Rubbed Chestnut Finish fixture or UPC
718212222119 Oil Rubbed Chestnut Finish fixture.
CAUTION:
1. Before starting installation of this fixture or removal of a previous fixture,
disconnect the power by turning off the circuit breaker or by removing the fuse at
the fuse box.
2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL
QUESTIONS.
3. If you have any non-electrical questions about this fixture, please contact our
Customer Service Team at 1-800-986-3460 or visit
HOMEDEPOT.COM/HOMEDECORATORS. Please reference your SKU
1002099636 Oil Rubbed Chestnut Finish fixture or UPC 718212222119 Oil
Rubbed Chestnut Finish fixture.
4. Keep your receipt and these Instructions for Proof of Purchase.
SENSOR
Least Sensitivity
Fig 5
SENSOR
Best Sensitivity

Page 5
TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION (Not included):
Light Bulb Safety goggles Silicon Rubber Sealant Wire strippers
SKU 1002099636 60 Watt maximum for exterior use
Flathead screwdriver Phillips screwdriver Electrical tape Wire cutters
PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):
2 screw (#1) 2 Cap Nuts (#3)
ASSEMBLY INSTRUCTIONS:
1. Shut off power at the fuse box or circuit breaker box, if necessary remove old fixture and all
mounting hardware from outlet box.
2. Carefully unpack your new fixture and lay out all the parts on a clear area, take care not to lose
any small parts necessary for installation.
3. Install light bulbs in accordance with the fixtures specifications. (DO NOT EXCEED THE
MAXIMUM WATTAGE RATING!!)
4. Glass panel is pre-assembled, if doing glass replacement, unscrew Screws (#1), separate
Fixture frame (#7) from cover (#2) and take off broken glass panel, then insert the Glass Panel
(#6) into the Fixture frame (#7). Finally screw the Screws (#1) back to secure the fixture frame
with the cover.

Page 6
ASSEMBLY:
PARTS INCLUDED FOR INSTALLATION (parts are not to scale):
1 Ground Screw (#12) 2 Outlet Box Screws (#13) 2 Mounting Screws (#10)
1 Cross Bar (#11) 3 Wire Connectors (#8)
INSTALLATION INSTRUCTIONS:
1. Screw the two Mounting Screws (#10) into the cross bar (#11). Mount the cross bar (#11) to the
Outlet Box (#9) using the two provided Outlet Box Screws (#13). [Make sure the threads of the
Mounting Screws (#10) are facing outside when the cross bar (#11) is attached to the Outlet Box
(#9).] The side of the Cross Bar (#11) marked “GND” must face out.
2. Connect the white wire from the fixture to the white wire from the Outlet Box (#9), and the black
wire from the fixture to the black wire from the Outlet Box (#9). Cover the two wire connections
using the provided Wire Connectors (#8). Wrap the two wire connections with electrical tape for
a more secure connection. If your outlet box has a ground wire (green or bare copper), connect
fixture’s ground wire to it using the wire connector (#8). Otherwise connect the copper ground
from the fixture to Ground screw (#12) on the Cross bar (#11). Note: If you have electrical
questions, consul
t your local electrical code for approved grounding methods.
3. Cap Nut
4. Back Plate
1. Screw
5.Light Bulb
7. Fixture Frame
6.Glass Panel
2. Cover

Page 7
INSTALLATION INSTRUCTIONS (CONTINUED):
3. Mount the body of the fixture on the wall by aligning the protruding Mounting Screws (#10) all
the way through the holes on the Back Plate (#4). Be careful not to pinch any of the wires
between the fixture and the Outlet Box (#9). Tighten the fixture to the wall by screwing the two
cap nut (#3) onto the two protruding Mounting Screws (#10).
4. Once the fixture is mounted on the wall, caulk the space between the wall and the upper 3/4 area
of the Back Plate (#4) to prevent water seeping into the Outlet Box (#9). Leave the bottom 1/4
area un-caulked for drainage of any water which might leak into the enclosure.
5. Installation is complete. Turn on the power at the circuit breaker or fuse box. Turn the light
switch on to activate the fixture.
INSTALLATION:
PRODUCT MAINTENANCE:
1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water,
never a solvent) to wipe the glass and surface of the fixture.
2. To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit
breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth
(use clean water, never a solvent) to wipe the inside glass and interior surface of the fixture.
3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft cloth to
dust or wipe carefully.
8.Wire Connector
9.Outlet Box
10.Mounting Screw
12.Ground Screw
13.Outlet Box Screw
11.Cross Bar
3.Cap Nut

Page 8
TROUBLESHOOTING:
LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period
of three (3) years from date of purchase. This warranty applies only to the original consumer purchaser and only to
products used in normal use and service. If this product is found to be defective, the manufacturer’s only
obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion,
provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations,
neglect or mishandling. This warranty shall not apply to any product that is found to have been improperly
installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This
warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration,
or faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not
apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal
wear and tear. The manufacturer does not warrant and specially disclaims any warranty, whether express or
implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer
specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage,
including but not limited to any labor / expense costs involved in the replacement or repair of said product.
SYMPTOM Possible Cause Solution
In motion sensing mode,
the light does not turn
on when there is motion
Wall switch or circuit breaker is off Turn on a switch or circuit breaker.
Light bulb may be dead. Test the light bulb in a known working
light fixture
Light bulb is loose. Tighten the light bulb in the socket.
Incorrect or loose wire connections. Check wire connections.
Too much sunlight is shining into photocell
sensor in the early evening.
Relocate fixture away from a western
facing wall.
Too much light is shining onto photocell
sensor due to another light source, such as a
street lamp or other light fixture.
Eliminate or turn off other light source,
block other light source from shining
onto photocell sensor, or relocate
fixture.
In motion sensing mode,
the light stays on
continuously.
False triggering caused by a heat source,
such as a heater or dryer vent, or heated
swimming pool.
Eliminate heat source or relocate fixture
The light comes on for
no apparent reason
Street or sidewalk traffic is triggering
motion sensor Lower the sensitivity.
False triggering caused by a heat source,
such as a heater or dryer vent, or heated
swimming pool.
Eliminate heat source or relocate fixture
The light comes on
during the daytime or
too early in the evening
The fixture may be installed in a shaded
area, such as under a porch or eave,
preventing daylight from shining onto the
photocell sensor.
Relocate the fixture

Page 9
1 luz de la pared exterior de la linterna con sensor de movimiento
Home Depot SKU 1002099636 (UPC 718212222119)
(Castaña Aceitado)
MANUAL DE INSTRUCCIONES

Page 10
Gracias por la compra de este accesorio Home Decorators Collection Linterna de
pared para el exterior Este producto ha sido fabricado con los más altos niveles de
seguridad y calidad. El acabado de esta linterna es resistente a la intemperie, pero
con el tiempo se va ir desvaneciendo naturalmente.
ADVERTENCIA: Este equipo ha sido probado y cumple con los límites para un dispositivo
digital de Clase B, según la Parte 15 de las normas de la FCC. Estos límites están diseñados para
proporcionar una protección razonable frente a interferencias perjudiciales en una instalación
residencial. Este equipo genera, utiliza y puede irradiar energía de frecuencia y, si no se instala y
utiliza de acuerdo con las instrucciones, puede causar interferencias en las comunicaciones de radio.
Sin embargo, no hay garantía de que no se produzcan interferencias en una instalación particular. Si
este equipo causa interferencias perjudiciales en la recepción de radio o televisión, lo cual puede
determinarse apagándolo y encendiéndolo, se recomienda al usuario que intente corregir la
interferencia mediante una o más de las siguientes medidas:
• Reorientar o reubicar la antena receptora.
• Aumentar la separación entre el equipo y el receptor.
• Conectar el equipo a una toma de un circuito distinto de aquel al que está conectado el receptor.
• Consulte al distribuidor oa un técnico de radio / TV para obtener ayuda.
Los cambios o modificaciones no aprobados expresamente por la parte responsable
del cumplimiento podrían anular la autoridad del usuario para operar el equipo.
CARACTERÍSTICAS:
1. SENSOR DE MOVIMIENTO DE FUNCIONES - El sensor de movimiento se activa
automáticamente al anochecer y se enciende la luz cuando detecta una fuente de calor en
movimiento, como personas y vehículos se encuentran dentro de su área de cobertura. El sensor de
movimiento se mantendrá activo durante toda la noche y desactivar en la madrugada.
(Nota: Cuando se aplica potencia en primer lugar, la luz se encenderá durante aproximadamente 20
segundos para permitir que la corriente eléctrica para estabilizar vez estabilizado el software en las
funciones del modo de prueba y el modo automático del sensor de movimiento puede ser llevada
El sensor tiene 2 perillas uno es para ajustar la sensibilidad y el segundo es un temporizador de
retardo de cierre. (Véase la figura 1) el sensor de movimiento se debe girar como Fig.2 para ajustar
la ubicación perillas de la parte posterior.)
Modo de prueba MODO AUTOMÁTICO
Trabaja en De día y de noche La noche solo
Activada por Mociones mociones
A tiempo A medida que el movimiento existente A medida que el movimiento existente
Tiempo de apagado de retraso 5 Sec. 10 seg. ~ 10 Min
Fig.2
La luz del casquillo gira hacia la derecha para facilitar
el acceso a los ajustes del sensor de movimiento
Vuelta
1' 5'
10'
TIMER
13Ft
5Ft
21Ft
30Ft
Auto
Test
SENSITIVITY
Fig.1