HOME RETAIL GROUP Winchester 656/7004 User manual

Dimensions
Width - 126.3cm
Depth - 42.5cm
Height - 90.8cm
Issue 1 - 10/03/10
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 160 1490
Winchester - Chest of 4+4 Drawers
Assembly Instructions - Please keep for future reference
656/6957
656/7004

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your oor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance

Large drawer front x 4
(71.3 x 19cm)
Components - Panels
Please check you have all the panels listed below
2
Top panel x 1 (126.3 x 42.5cm)
3
Left side panel x 1
(39.5 x 88.5cm)
2
Right side panel x 1
(39.5 x 88.5cm)
1
Vertical partition wall x 1
(38.9 x 77.6cm)
5
10
Back panel x 1
(114.1 x 80.4cm)
6
Right hinge frame x 1
(5.3 x 88.5cm)
7
Bottom panel x 1
(112.3 x 39.1cm)
4
Right drawer side x 8
(35 x 10cm)
11 Left drawer side x 8
(35 x 10cm)
12
Left hinge frame x 1
(5.3 x 88.5cm)
8
Large drawer back x 4
(70.6 x 10cm)
13
Bottom plinth x 1
(112.2 x 5.3cm)
9
Handle x 12
(10.5 x 1.9cm)
15
Large drawer base x 4
(71 x 33.9cm)
14
Small drawer back x 4
(31.3 x 10cm)
18 Small drawer front x 4
(37 x 19cm)
19 Small drawer base x 4
(31.7 x 33.9cm)
20
If you have damaged or missing components,
call the Customer Helpline: 0870 160 1490

3
Please check you have all the ttings listed below
Feet x 4
A
Screw x 37
E
8/30mm Wooden dowel x 24
B
Small locking nut x 16
H
6/30mm Wooden dowel x 32
C
Key x1
I
Drawer base support x 8
Q
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
9mm Screw x 32
F
13mm Screw x 1
Nail x 50
D
20mm Screw x 32
K
Underlay x 2
R
O
Runner left B x 8
M
P
Runner right B x 8
N
Y
Runner left A x 8
L
Large locking nut x 21
G
Plastic dowel x 32
J
50mm Screw x 2
R
Runner right A x 8
S
35mm Screw x 24
Components - Fittings
Tools required
Ruler - Use this ruler to help correctly identify the screws
100 20 30 40 50 60 70 80 90 100
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Hammer
Spirit level
Ruler/tape
measure
L
12mm Screw x 16
Z4

Attaching runners
a: Position runners T
15mm in from front edge
of the left side panel 1.
Slide top of the runners
back.
Fix through holes shown
using screws C.
Assembly Instructions
F
Step 1
Attaching runners
a: Position left runners
A Land right runners A
Ron to the drilled holes
of the left and right side
panels 1and 2and
the left side of vertical
partition wall 5.
Fix through holes shown
using screws Fand Z4.
4
b: Turn over the vertical
partition wall 5and
attach runners A Las
shown using screws F
and Z4.
c: Attaching feet
Position plastic feet A
to the left and right side
panels 1, 2from
below and x them using
the hammer.
L
b: Right side 5
c:
R
L
1
2
A
a:
F
F
R
5
Left side
F
R
Z4
R
Z4
L
Z4

Attaching runners
a: Position runners T
15mm in from front edge
of the left side panel 1.
Slide top of the runners
back.
Fix through holes shown
using screws C.
Assembly Instructions
E
1
2
E
Step 3
Attaching the bottom
panel and vertical
partition wall
Insert wooden dowels B
into the bottom panel 4
and partition wall 5and
place on left and right
side panels 1, 2.
Align correctly and insert
large locking nuts Gand
turn them clockwise to
lock.
Place partition wall 5
onto the bottom panel
4. Fix through the
bottom panel 4using
screws Q, thighten
using key I. Align
correctly and insert large
locking nuts G.
G
I
Q
B
11 mm
5
Preparation for the
attaching of top panel
and bottom panel
Insert screws Einto the
drilled holes of the left
and right side panels 1
and 2, top panel 3.
Insert wooden dowels B
into the bottom panel 4
as shown on the picture.
Step 2
E3
4
B
1
5
2
4
B
B
G
Q
G
B

Attaching runners
a: Position runners T
15mm in from front edge
of the left side panel 1.
Slide top of the runners
back.
Fix through holes shown
using screws C.
Assembly Instructions
Frame assembly
Insert screws Ein to the
frames 7, 8, 9.
Insert wooden dowels B
as shown, align correctly
and insert large locking
nuts Gin to the frame
9, place the frames 7
, 8and turn locking nuts
clockwise to lock.
Step 5
6
7
9
8
E
E
7
8
E
Step 4
9
E
E
G
B
G
B
11 mm
G
B
G
B

Attaching runners
a: Position runners T
15mm in from front edge
of the left side panel 1.
Slide top of the runners
back.
Fix through holes shown
using screws C.
Assembly Instructions
Step 6
Step 7
Step 8
Attaching top panel
Insert wooden dowels
Binto the top edges as
shown, align correctly
and insert large locking
nuts Ginto left and right
side panels 1and 2
and vertical partition wall
5, place the top panel
3and turn locking nuts
clockwise to lock.
Attaching back panels
With help, carefully lay
chest down.
Position back panel 6
in position on the back
of chest. Position nails
D5 mm in from side
edge of the back panel
6with distance 100 mm
between each other. Fix
them using the hammer.
2
D
5 mm
100 mm
1
G
3
B
G
Note: You must
ensure the chest
is square before
attaching the back
panels.
B
11 mm
11 mm
5
B
9
8
7
5
2
1
G
B
G
4
6
Attaching the frame
Insert wooden dowels
Binto the edge of
the left and right side
panels 1, 2.
Align correctly and
insert large locking
nuts Ginto left and
right side panels 1,
2and bottom panel
4, place the frame
and turn locking nuts
clockwise to lock.
B
B
7

Attaching runners
a: Position runners T
15mm in from front edge
of the left side panel 1.
Slide top of the runners
back.
Fix through holes shown
using screws C.
Assembly Instructions
Step 9
Drawer assembly
a: Insert screws Einto
large or small drawer
front 10 , 19 .
b: Insert wooden dowels
Bin to large or small
drawer front 10 , 19
and place left and right
drawer sides 11 , 12 .
c: Slide large or small
drawer base 14 , 20 into
the grooves.
d: Place large or small
drawer back 13 , 18
onto sides.
e: Align correctly and
insert small locking nuts H
into left and right drawer
sides 11 , 12 and turn
them clockwise to lock.
f: Insert plastic dowels J
into left and right drawer
sides 11 , 12 and large
or small drawer back 13 ,
18 and x it together using
the hammer.
g: Position left and right
runners B M, Non
to left and right drawer
sides 11 , 12 , x using
screws K.
10
14
13
K
M
N
K
J
J
H
8
a: b:
c: d:
e: f:
g:
E
12 12
12
12
11 11
11
11
13
13
K
K
19
18
20
18
18
11
12
B
19
10
continued on next page
Repeat assembly for
the remaining drawers.

Attaching runners
a: Position runners T
15mm in from front edge
of the left side panel 1.
Slide top of the runners
back.
Fix through holes shown
using screws C.
Assembly Instructions
P
S
15
15
S S
h: i:
P
h: Large drawers only:
Position 2 drawer base
supports Ponto the
underside of the large
drawers as shown. Fix
using supplied screw.
i: All drawers: Attach
handles 15 to drawer
fronts using screws S.
Fixing to wall
It is recomended that the
chest is xed to a wall.
Poke wall strap X
through the hole in the
back panel and x it to
top panel underneath
using screw Yand
underlay O.
Mark xing hole onto
wall. Drill a hole and
insert a suitable wall
plug. Fix wall strap X
using a suitable screw.
With help, move chest
into position.
Step 10
Warning:
The chest
is heavy.
Lift with care.
Warning:
Before drilling,
check wall for
hidden pipes and
cables.
X
X
X
O
Y
Note: Wall xings are not
supplied with this unit.
The correct type of xing must
be used for your wall, seek
professional advice if in doubt.
Step 9 - continued
9

Attaching runners
a: Position runners T
15mm in from front edge
of the left side panel 1.
Slide top of the runners
back.
Fix through holes shown
using screws C.
Assembly Instructions
Step 11
10
Inserting drawers
Insert the drawers
moving up and down as
shown and ensure that
wheels t onto left and
right runners L, R.
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 160 1490
Home Retail Group Plc, 489 - 499 Avebury boulevard, Milton Keynes, MK9 2NW
R
L