home8alarm WGO2001 User manual

1
Garage Door Control Button
WGO2001
User Manual
home8alarm.com
1-844-800-6482 | [e-mail]

Garage Door Control Button User Manual
V1.0 2017
1
Table of Contents
Chapter 1. Introduction.................................................................................3
1.1 System Requirement ...............................................................................................3
Chapter 2. Hardware Overview.....................................................................4
Chapter 3. Garage Door Control Button Setup ...........................................5
3.1 Powering up the sensor...........................................................................................5
3.1.1 Press and hold down the button.................................................................................................. 5
3.1.2 While holding down the button, attach the power cable.............................................................. 6
3.1.3 Continue holding down the button for 5 seconds until blinking (orange-red) starts .................... 6
3.2 Adding the Sensor to an OPU/Shuttle......................................................................7
3.2.1 Tap the menu icon to show the sidebar menu...................................................................... 7
3.2.2 Tap “Device Management”. If you have more than one security shuttle, you may need to swipe
left more than once to find the OPU/Shuttle to which you would like to add the sensor............................. 7
3.2.3 Tap on the ‘+’ next to Sensor List. Tap on ‘Sensor’ at the bottom of the page. ........................... 8
3.2.4 Follow the on-screen instructions and press “Next”. Scan the QR-code located on the bottom of
the sensor and the “device adding” process will begin. .............................................................................. 8
3.2.5 When the activation is completed, the sensor will be added to the device management page. In
the illustration below, the name of the Security Shuttle is “Location10” and the name of the sensor is
“Garage Door Opener E34D…”................................................................................................................... 9
3.3 Adding the Sensor to a Virtual OPU/Shuttle...........................................................10
3.3.1 Tap the menu icon to show the sidebar menu....................................................................10
3.3.2 Tap “Device Management”. If you have more than one security shuttle, you may need to swipe
left more than once to find the “New OPU/Shuttle” page.......................................................................... 10
3.3.3 Select “Wi-Fi Sensor” and press “Next”......................................................................................11
3.3.4 Follow the on-screen instructions and press “Next”. ..................................................................11
3.3.5 Scan the QR-code located on the bottom of the sensor and the “device adding” process will
begin. Enter the password for your Wi-Fi Network and press “Next”........................................................12
3.3.6 When the activation is completed, the sensor will be added to the device management page. In
the illustration below, the name of the Security Shuttle is “Location10” and the name of the sensor is
“Garage Door Opener E34D…”.................................................................................................................12
Chapter 4. Garage Door Control Button Settings.....................................13
4.1 Display Name.........................................................................................................14

Garage Door Control Button User Manual
V1.0 2017
2
Chapter 5. Starting to Use the Garage Door Control Button....................15
5.1 Once the device is successfully added, choose one of the following 3 installation
methods (please review all methods thoroughly before choosing which might be best for
your scenario):.................................................................................................................15
5.1.1 Installation –Method 1 –Replace Existing Opener ..................................................................15
5.1.2 Installation –Method 2 –Connect To Existing Opener ............................................................. 17
5.1.3 Installation –Method 3 –Directly Connect To the Garage Door Motor.....................................19
5.2 Operating –You can control your garage door remotely via the APP or by simply
pressing the Garage Door Control Button........................................................................21
5.2.1 Local control by pressing button –Press button to open/close your garage door. LED indicator
will turn red and trigger an action.............................................................................................................. 21
5.2.2 Remote control via the APP –There are 2 methods in opening the garage door (Note: Every
action will have a 15-second cool-down period before the next action can be processed. It is represented
by a grey control button)............................................................................................................................ 22
Chapter 6. Notifications..............................................................................24
Chapter 7. Other Information......................................................................26
7.1 LED Indicator.........................................................................................................26
7.1.1 Green –Power on......................................................................................................................26
7.1.2 Blinking Green –WiFi disconnect..............................................................................................26
7.1.3 Red –Open/Close action is in progress....................................................................................26
7.2 Reset .....................................................................................................................26
7.2.1 A hard reset will restore your device to factory default settings. ............................................... 26
7.2.2 Press and hold down the reset button on the back of device with a pin for approximately 5-8
seconds. 26
7.2.3 The LED indicator will blink red and green then orange to blinking green................................26
Appendix –Glossary of Terms...................................................................27

Garage Door Control Button User Manual
V1.0 2017
3
Chapter 1. Introduction
The Garage Door Control Button allows you to remotely open and close your garage door. The owner and
authorized users will be sent push notifications when the device is in operation. Working in conjunction with
a Home8 camera, you can view the garage door opening and closing in live streaming video via the Home8
app.
Key features and specifications of the sensor.
Wi-Fi and Security: IEEE 802.11b with WAP/WPA2 PSK
Use the Home8 mobile app to open and close your garage door remotely while streaming live video
Sends a push notification to owner and all authorized users when it’s in operation for added security
Keeps a time-stamped log of when it’s in use
Max. switching current: 2A
Max. switching capacity: 62.5VA/ 60W
15-second cooldown period for every action
1.1 System Requirement
This section explains the system requirement when using the camera.
Network
When camera is
connected to Security
Shuttle*
Router with
- 10/100Mbps RJ45 LAN port
- DHCP service
When camera is
connected directly to
Wi-Fi Router
Wi-Fi Router supports
- IEEE 802.11n, 802.11g, 802.11b
- WEP/WPA2-PSK Wireless Security
Mobile Device
An Apple iPhone, iPad, or Android mobile device with:
- iOS (version 8.1 above)
- Android (version 4.1 above)
* See Appendix –Glossary of Terms.

Garage Door Control Button User Manual
V1.0 2017
4
Chapter 2. Hardware Overview
This section provides an overview of the Garage Door Control Button and its accessories.
LED status
light
Operation
button
Reset to factory
setting button

Garage Door Control Button User Manual
V1.0 2017
5
Chapter 3. Garage Door Control Button Setup
3.1 Powering up the sensor
3.1.1 Press and hold down the button

Garage Door Control Button User Manual
V1.0 2017
6
3.1.2 While holding down the button, attach the power cable
3.1.3 Continue holding down the button for 5 seconds until blinking (orange-red)
starts

Garage Door Control Button User Manual
V1.0 2017
7
3.2 Adding the Sensor to an OPU/Shuttle
Before you begin using the sensor, it will need to be added to a system first.
3.2.1 Tap the menu icon to show the sidebar menu.
3.2.2 Tap “Device Management”. If you have more than one security shuttle, you
may need to swipe left more than once to find the OPU/Shuttle to which you
would like to add the sensor.

Garage Door Control Button User Manual
V1.0 2017
8
3.2.3 Tap on the ‘+’ next to Sensor List. Tap on ‘Sensor’at the bottom of the page.
3.2.4 Follow the on-screen instructions and press “Next”. Scan the QR-code located
on the bottom of the sensor and the “device adding”process will begin.

Garage Door Control Button User Manual
V1.0 2017
9
3.2.5 When the activation is completed, the sensor will be added to the device
management page. In the illustration below, the name of the Security Shuttle
is “Location10” and the name of the sensor is “Garage Door Opener E34D…”.

Garage Door Control Button User Manual
V1.0 2017
10
3.3 Adding the Sensor to a Virtual OPU/Shuttle
Before you begin using the sensor, it will need to be added to a system first.
3.3.1 Tap the menu icon to show the sidebar menu.
3.3.2 Tap “Device Management”. If you have more than one security shuttle, you
may need to swipe left more than once to find the “New OPU/Shuttle” page.

Garage Door Control Button User Manual
V1.0 2017
11
3.3.3 Select “Wi-Fi Sensor” and press “Next”.
3.3.4 Follow the on-screen instructions and press “Next”.

Garage Door Control Button User Manual
V1.0 2017
12
3.3.5 Scan the QR-code located on the bottom of the sensor and the “device
adding”process will begin. Enter the password for your Wi-Fi Network and
press “Next”.
3.3.6 When the activation is completed, the sensor will be added to the device
management page. In the illustration below, the name of the Security Shuttle
is “Location10” and the name of the sensor is “Garage Door Opener E34D…”.

Garage Door Control Button User Manual
V1.0 2017
13
Chapter 4. Garage Door Control Button Settings
For relevant sensor setting adjustments, follow the steps shown below.
1. Tap the menu icon to show the sidebar menu.
2. Tap “Device Management”; then tap “Garage Door Opener XXXXXxxxx” under “Sensor List” to reach the
“Edit Sensor” page.
The following illustration shows the sensor setting that can be adjusted.
Display Name

Garage Door Control Button User Manual
V1.0 2017
14
4.1 Display Name
This option allows you to change the display name.
To do so, tap “Display Name”; then, change the name
according to your preference. When finished, tap the
check icon located on the upper-right corner.
Note: The maximum length of the display name is 40
characters.
.

Garage Door Control Button User Manual
V1.0 2017
15
Chapter 5. Starting to Use the Garage Door Control Button
At this stage, your sensor is now ready for use.
5.1 Once the device is successfully added, choose one of the following
3 installation methods (please review all methods thoroughly
before choosing which might be best for your scenario):
5.1.1 Installation –Method 1 –Replace Existing Opener
5.1.1.1 Unscrew opener from the wall
5.1.1.2 Access the back of the opener
5.1.1.3 Unscrew wires from the opener (Note: The 2 wires will not cause a harmful electrical shock)

Garage Door Control Button User Manual
V1.0 2017
16
5.1.1.4 The remaining wires will go into the Garage Door Control Button
5.1.1.5 Insert wires into the Garage Door Control Button (one per hole, either hole choice is fine)
5.1.1.6 Attach the power adapter
5.1.1.7 Mount the Garage Door Control Button via Double-sided tape or screws

Garage Door Control Button User Manual
V1.0 2017
17
5.1.2 Installation –Method 2 –Connect To Existing Opener
5.1.2.1 Unscrew opener from the wall
5.1.2.2 Access the back of the opener
5.1.2.3 Loosen the screws (Note: The 2 wires will not cause a harmful electrical shock)
5.1.2.4 Attach a U-fork wire to the top screw

Garage Door Control Button User Manual
V1.0 2017
18
5.1.2.5 Attach a U-fork wire to the other screw
5.1.2.6 Tighten the screws
5.1.2.7 Remount the existing opener
5.1.2.8 Insert wires into the Garage Door Control Button (one per hole, either hole choice is fine)

Garage Door Control Button User Manual
V1.0 2017
19
5.1.2.9 Attach the power adapter
5.1.2.10 Mount the Garage Door Control Button via Double-sided tape or screws
5.1.3 Installation –Method 3 –Directly Connect To the Garage Door Motor
5.1.3.1 Access the wire panel of the motor unit
5.1.3.2 Loosen the garage door opener wire screws (Note: The 2 wires will not cause a harmful electrical shock)