homechoice Buhle Transformer Bed User manual

Buhle Transformer Bed
assembly instruction
Shop online – go to
homechoice.co.za
Please follow these guidelines for safe assembly:
Please make sure that you have all the parts and hardware items listed before you start
assembling your product. If you nd that something is missing, please do not assemble.
Contact our Customer Service on 0861 466 324.
HomeChoice will not be held liable for damages caused by improper assembly.

Assembly and conguration Instructions
Step 1 Step 2 Complete
Congratulations!
You have just successfully
transformed your cot into a bed.
Remove the ladder rail and
push in the hole caps. Keep the
rail and bolts safe in the event
you need to transform into a cot
again.
While someone holds the top
ladder rail, using the Allen key
(hex key), remove the 4 bolts
that hold the ladder.
Your Buhle Transformer Bed will allow you to change the conguration to suit your needs, giving you
many years of use from your furniture.
Below are the 3 dierent congurations:
Cot Bed Bench/Couch
Transforming the cot into a bed
Part Pieces
14 sets of connecting screws 8 pieces
Parts List

If you nd that something is missing, please contact our Customer Service on 0861 466 324.
NOTE: Furniture is heavy, and trying to do this alone and not following these precautions will place you in danger of injuring yourself.
To avoid possible injury, at least 2 people must perform any conguration changes, and the bedding and mattress must be removed.
Step 1 Step 2 Step 3
Using 2 people, lift the top
frame o the base and put it
down on the oor.
Hint: Pull up straight to avoid
sticking.
Using the Allen key (hex key),
remove the 4 bolts that hold the
2 support rails, one on each side.
Lower the 2 support rails down
about 15cm to the lower place
setting.
Step 4 Step 5 Complete
Congratulations!
You have just successfully
transformed your bed into a
couch/bench.
Again using 2 people, lift the top
frame o the oor and replace
carefully over the base.
Remember to keep it level to
avoid sticking.
Using the Allen key (hex key)
again, replace the 4 bolts that
hold the 2 support rails, now at
the higher setting.
Drill on lower
mark
This is the easiest transformation, but to avoid potentially damaging the bed, it will still require two
people – one to hold the rails while the other unscrews the bolts. You can perform these steps in
reverse in order to transform the couch back into a bed.
Transforming the bed into a couch

Care and maintenance of furniture:
IMPORTANT:
Congratultaions on your little one! As a cot or bed, this product is suitable for use for
children weighing up to 50kg or less than 1.3 metres tall. Carefully read through this manual
and follow each step to ensure a safe experience for your child. Please keep this instruction
manual handy for future reference.
• Warning: Do not use if any part is broken, torn or missing, and use only spare parts
approved by the manufacturer.
• Warning: Do not leave anything in the cot or place the cot close to another product
which could provide a foothold or present a danger of suocation or strangulation, e.g.
strings, blind/curtain cords, etc.
• Warning: Do not use more than one mattress in the cot.
• Warning: Be aware of the risk of open res and other sources of strong heat, such as
electric bar res, gas res and electrical plugs near wooden furniture.
• This product is suitable for a mattress of 1400mm in length and 700mm in width.
• The length and width of the mattress shall be no less to ensure the gap between the
mattress and the sides and ends does not exceed 30mm.
• Children are likely to play, bounce, jump and climb in the cot, Therefore, the cot should
not be placed too close to other furniture or windows, blind cords, curtain pulls or other
strings. It should be placed either tight to any wall or have a gap of 300mm between
the wall and the side of the cot/bed.
• To prevent injury from falls, the cot should no longer be used in the cot conguration
once he/she is able to climb out of the cot.
• All assembly ttings should be tightened properly and should be checked regularly and
re-tightened as necessary.
• Your furniture can be cleaned by wiping with a damp cloth and drying with a soft, clean
cloth.
• Do not use abrasives, bleach, alcohol or ammonia-based household polishes.
Installation tools required:
• Flat screwdriver
• Allen key (supplied)
Please recycle the packaging to protect the environment