HOMEDEPOT ACNS18V User manual

ITEM # ACNS18V
18 GAUGE BRAD NAILER/STAPLER
INSTRUCTION MANUAL
READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS
PRODUCT.
This manual provides important information on proper operation & maintenance.
Every effort has been made to ensure the accuracy of this manual. These
instructions are not meant to cover every possible condition and situation that
may occur. We reserve the right to change this product at any time without
prior notice.
IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE
OR UNSAFE, DO NOT OPERATE THIS PRODUCT!
HAVE QUESTIONS? CALL US FIRST FOR ASSISTANCE.
If you experience a problem, have questions or need parts for this product, call
Customer Service at 636-532-9888, Monday-Friday, 8 AM - 4 PM Central
Time. A copy of the
is required.
FOR CONSUMER USE ONLY –
NOT FOR PROFESSIONAL USE.
KEEP THIS MANUAL, SALES RECEIPT & APPLICABLE
WARRANTY FOR FUTURE REFERENCE.

ITEM # ACNS18V BRAD NAILER/STAPLER
1
SPECIFICATIONS
Model
ACNS18V
Battery Charge
100-240V, 50/60Hz
Input Voltage
20V DC, 2000mAh
Firing Speed
Average 60 nails/min ; Max 100 nails/ min
Magazine Capacity
Holds up to 100 maximum nails/staples
Length of Brad Nails
Use only 3/4” – 2” 18 Gauge Brad Nails
Length of Staples
Use only 3/4” – 1-1/2” 18 Gauge Light Duty Staples
Overall Dimensions:
10.75” W x 10” H x 3.5” D
PACKAGE CONTENTS
1 - Brad Nailer/Stapler
1 - Pack (18 Ga Staples / 1-1/2” 200 Pieces) (18 Ga Brad Nails / x 2” 200 Pieces)
1 - Battery
1 - Charger
FEATURE DIAGRAM

ITEM # ACNS18V BRAD NAILER/STAPLER
2
READ THESE IMPORTANT SAFETY RULES
a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.
b) Avoid dangerous environments. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may
ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause
you to lose control.
d) Keep the tool pointed away from yourself and others and body parts
safety equipment. Always wear eye protection and ear protection. Safety equipment such as
dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions.
e) Never modify the plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric
shock.
f) Do not keep the trigger or safety depressed during loading fasteners or the unintentional
firing of a fastener would cause personal injury.
g) Disconnect the tool from the power source before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
h) Do not fire if the nails/staples are jammed. This will cause damage to the driver blade and
could invite accidents.
i) DO NOT use on hard surface such as rock, concrete, masonry, bricks or steel. Person injury
or damage to the power tool could result.
j) Do not drive fasteners close to the edge of the work piece.
k) Do not drive fasteners on top of nailed fastener.
l) Only use parts and accessories recommended by manufacturer.

ITEM # ACNS18V BRAD NAILER/STAPLER
3
BATTERY TOOL USE, CHARGING AND CARE
a) Recharge only with the charger and the battery packs included with this product.
b) Ensure the switch is in the off position before inserting battery pack.
c) Do not open the battery. Danger of short-circuiting.
d) Protect the battery against heat, e.g., also against continuous sun irradiation and fire.
There is danger of explosion.
e) Do not short-circuit the battery. There is danger of explosion.
f) Battery leakage (liquid ejection). Under abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, flush
them with clean water for at least 10 minutes, then seek immediate medical attention. Liquid
ejected from the battery may cause irritation or burns.
g) Care when charging. Make sure cord for the charger is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage or stress. Do not operate charging system
with damaged cord or plug.
h) Battery recycling and disposing. All batteries must be recycled or disposed of properly (see
section on Environment).
INTENDED USE
The tool is intended for tacking of cardboard, insulating material, fabric, foils, leather and similar
materials on surfaces of wood or materials similar to wood. The machine is not suitable for the
attachment of wall.
LED FUNCTION INDICATOR:

ITEM # ACNS18V BRAD NAILER/STAPLER
4
LED Red on=Low battery
LED Red flashing=The nails/staples are jammed.
LED Green on=No nails, power tool in dry fire protection
LED Green flashing=Overheat / power tool in overheat protection mode
（The tool cannot fire in this situation, wait until it has cooled down）
Charger:
Red LED on=Battery charging.
Green LED on=Battery fully charged.
OPERATING INSTRUCTION
Battery Charging: Battery packs for this tool are shipped in a low charge condition to
prevent possible problems.
a) Insert the power outlet into the port on battery pack. Plug the charger power supply into a
power outlet. The indicator light on the charger will be red (battery is charging).
b) When batteries become fully charged (about 1~1.5 hours), the indicator on the charger will
turn green. Unplug the charger from power supply and remove the battery pack.
NOTE: A battery that is new or has not been used for a longer period does not develop its full
capacity until after approx. 5 charge/discharge cycles.
Do not recharge the batteries after use if they are not to be used for an extended period of time.
Recharge the batteries as and when they are required.
Do not recharge the recharge-required batteries after use if they are not cool down. Otherwise it
will be not charged fully.
Inserting and Removing the Battery Pack
a) Insert the battery pack into the grip until it clicks in place.
b) To remove the battery pack, with pressing the lock buttons simultaneously to pull the pack out of
the machine.