Homedepot Edco ds-18 User manual

Page 1

Tool Rental Center

MANUAL

EDCO

DS-18

37100-HD-11.17 REVISED STARTING SERIAL # 171010026

18” DOWNCUT - CONCRETE AND ASPHALT

WALK BEHIND SAWS

SKU # MODEL # POWER OPTION

37100-HD DS18-13H HONDA GASOLINE ENGINE MODEL GX390U1-QXC9

Page 2

READ AND UNDERSTAND THE OPERATORS INSTRUCTION MANUAL THOROUGHLY

BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT.

Death or serious injury could occur if this machine is used improperly.

Extreme care must be taken when operating electric

models with water present: Ensure power cord is prop-

erly grounded, is attached to a Ground-Fault-Interrupter

(GFI) outlet, and is undamaged.

•Check all electrical cables - be sure connections are tight and

cable is continuous and in good condition. Be sure cable is

correctly rated for both the operating current and voltage of

this equipment.

•Improper connection of the equipment-grounding conductor can

result in a risk of electric shock. Check with qualied electri-

cian or service person if there is any doubt as to whether the

outlet is properly grounded. Adhere to all local codes and

ordinances.

•NOTE: In the event of a malfunction or breakdown, grounding

provides a path of least resistance for the electric current to

dissipate. The motor is equipped with a grounded plug and

must be connected to an outlet that is properly installed and

properly grounded. DO NOT modify the plug provided on the

motor. If the plug does not t the outlet have a qualied electri-

cian install the proper receptacle.

•Switch motor OFF before disconnecting power.

•Engine exhaust from this product contains

chemicals known to the State of California to

cause cancer, birth defects or other reproduc-

tive harm.

• Gasoline is extremely ammable and poisonous.

It should only be dispensed in well ventilated areas,

and with a cool engine.

•Small gasoline engines produce high concentra-

tions of carbon monoxide (CO) example: a 5 HP 4 cycle

engine operation in an enclosed 100,000 cu. ft. area with

only one change of air per hour is capable of providing

deadly concentrations of CO in less than fteen minutes.

Five changes of air in the same area will produce noxious

fumes in less than 30 minutes. Gasoline or propane pow-

ered equipment should not be used in enclosed or partially

enclosed areas. Symptoms of CO poisoning include, head-

ache, nausea, weakness, dizziness, visual problems and

loss of consciousness. If symptoms occur - get into fresh

air and seek medical attention immediately.

SAFETY

MESSAGES

SAFETY MESSAGES

Indicates an imminent hazard which, if not

avoided, will result in death or serious injury.

Indicates an imminent hazard which, if not

avoided, can result in death or serious injury.

Indicates hazards which, if not avoided, could

result in serious injury and or damage to the

equipment.

•Safety Instructions are proceeded by a graphic alert symbol

of DANGER, WARNING, or CAUTION.

ELECTRICAL POWERED EQUIPMENT

GASOLINE/PROPANE POWERED EQUIPMENT

•Equipment should only be operated by trained personnel in

good physical condition and mental health (not fatigued). The

operator and maintenance personnel must be physically able

to handle the bulk weight and power of this equipment.

•This is a one person tool. Maintain a safe operating distance

to other personnel. It is the operators’ responsibility to keep

other people (workers, pedestrians, bystanders, etc.) away

during operation. Block off the work area in all directions with

roping, safety netting, etc. for a safe distance. Failure to do so

may result in others being injured by ying debris or exposing

them to harmful dust and noise.

•This equipment is intended for commercial use only.

•For the operator’s safety and the safety of others, always keep

all guards in place during operation.

•Never let equipment run unattended.

•Personal Protection Equipment and proper safety attire must

be worn when operating this machinery. The operator must

wear approved safety equipment appropriate for the job such

as hard hat and safety shoes when conditions require. Hear-

ing protection MUST be used (operational noise levels of this

equipment may exceed 85db). Eye protection MUST be worn

at all times.

Keep body parts and loose clothing away from moving

parts. Failure to do so could result in dismemberment

or death.

•Do not modify the machine.

•Stop motor/engine when adjusting or servicing this equipment.

Maintain a safe operating distance from ammable

materials. Sparks from the cutting-action of this machine

can ignite ammable materials or vapors.

GENERAL INSTRUCTIONS

DUST WARNING

Some dust created by power sanding, sawing,

grinding, drilling, and other construction activi-

ties contains chemicals known to cause cancer,

birth defects, or other reproductive harm. Some

examples of these chemicals are:

•Lead from lead-based paints, and

•Crystalline silica from bricks and concrete and other

masonry products.

Your risk of exposure to these chemicals varies depending

on how often you do this type of work. To reduce your risk:

work in a well ventilated area, use a dust control system, such

as an industrial-style vacuum, and wear approved personal

safety equipment, such as a dust/particle respirator designed

to lter out microscopic particles.

•Do not disconnect power by pulling cord. To disconnect, grasp

the plug, not the cord.

•Unplug power cord at the machine when not in use and before

servicing.

Page 3

TOOL RENTAL CENTER MANUAL

DS-18

Section Page Number

Safety Messages and General Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

How To Order Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety Decal Reference Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4,5

Operating Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Changing The Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Dust and Crystalline Silica Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . 9

Lubrication Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Possible Blade Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Illustration 1: Main Grouping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12,13

Illustration 2: Arbor and Blade Guard Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14,15

Illustration 3: Engine Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16,17

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Maintenance Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

TABLE OF CONTENTS

HOW TO ORDER REPLACEMENT PARTS

 To insure product safety and reliability, always use

genuine EDCO replacement parts when making

repairs to the equipment.

 When calling for parts, specify the MODEL and

SERIAL number of the machine, which can be found

on the NAME PLATE. Keep that information in the

space provided. In addition to this information, give

part number, description, and quantity as listed on

the parts list to your parts representative.

 Please note: Due to improvements and changes

in the equipment, the illustrations shown may be

di󰀨erent than the actual machine.

FILL IN INFORMATION BELOW

Date of Purchase ______________________________

Model # _____________________________________

Serial # ______________________________________

SKU # ______________________________________

Page 4

This symbol means that the Operator’s, owners, instruction and/or manufacturer(s) manuals must be

read and understood before operating or attempting to operate this electrical, gasoline, diesel or

propane powered equipment, failure to do so can result in personal injury and possible death.

(Blue background with white pictogram.)

This symbol means that proper eye protection must be worn/used during the operation of this equipment. There is

a potential risk of operator eye damage, injury or loss of sight. This also applies to any personnel standing

nearby observing the operation of this equipment.

(Blue background with white pictogram.)

This symbol means that proper ear protection should be worn/used during the operation of this equipment.

There is a potential risk of operator hearing damage, injury or loss of hearing which will increase based on the

length of exposure. This also applies to any personnel standing nearby observing the operation of this equipment.

(Blue background with white pictogram.)

This symbol means that proper head protection should be worn/used during the operation of this equipment there

is a potential risk of operator head injury from foreign or loose objects the equipment might come in

contact with during operation. This also applies to any personnel standing nearby or observing the

operation of this equipment.

(Blue background with white pictogram.)

This symbol means that proper breathing protection or engineering controls must be worn/used during the

operation of this equipment there is a potential risk of operator lung damage. Repeated and/or substantial

inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis. In

addition, to California and some other authorities have listed respirable crystalline silica as a substance known

to cause cancer. When grinding/cutting/drilling such materials, always follow local respiratory precautions.

This also applies to any personnel standing nearby or observing the operation of this equipment.

(Blue background with white pictogram.)

This symbol means do not insert ngers/digits under any edge of the belt cover while the engine/

motor on the machine is running because personal injury and loss of ngers/digits may result.

(Black pictogram with red “No” symbol outline)

This symbol denotes the lifting point and means that if lifting of this equipment is necessary use a lifting

device that is designed to accomodate or exceed the weight of this machine. Check the Operator’s

manual for specications. Using a device that is not designed to accomodate or exceed the weight of this

machine could result in damage to the machine and personal injury. Do not lift equipment over people

because death or serious injury could result.

(Blue background with white pictogram.)

This GHS pictogram identies that the chemicals contained present serious health hazards.

(Black pictogram with red diamond symbol outline)

Safety Symbols

Page 5

This symbol means that the machine is heavy if the machine needs to be lifted onto or o󰀨 of a truck,

loading dock etc. that proper technique or heavy duty lifting device should be used, personal injury could result.