HomeSeer WFTT07-2 User manual

Page 1
HomeSeer WFTT07-2 Quick-Start Guide
Congratulations on your purchase! Your Tabletop Touchscreen is
ready to allow you to control your home! Please take a few minutes
to read through this guide to familiarize yourself with the steps
required to set up the Wi-Fi and HSTouch.
STEP #1 –WFTT07-2 Initial Set-up
Once you’ve unpacked your Control Pad 2 you should follow these
steps to getting started!
HomeSeer WFTT07-2 Hardware Installation
a) Unpack the WFTT07-2, AC power supply, and rubber feet.
b) Insert the USB cable into the AC adapter. Plug the AC
adapter into the wall and then into the back of the WFTT07-2.
(Do not use the mini-USB cable for power)
c) Turn on the product by holding down the power button for 3
seconds, and then the screen will show the starting logo.
Power on, Power off, Reset, and Hibernate
a) Power On: Turn on the device by holding down the power button for 3 seconds when the WFTT07-2 is off.
b) Power Off: Holding the power button for seconds and click ok to power off when prompted on the screen.
c) Restart: Hold the power button for 8 seconds to force the WFTT07-2 to turn off when the system has halted.
d) Sleep: Press the power button once to shut off the screen. (HSTouch and WiFi will stay connected)
Settings
Enter into the apps by clicking the upper right corner function button at the interface, and click ‘Settings’ to enter the
settings list interface, as the following. To control the volume, there are on screen buttons on the bottom action bar to
increase and decrease the volume.
a) Wi-Fi: turn on or turn off the wireless network connections, set and manage the wireless network access point.
b) Data usage: show the data message when using a 3G communication card.
c) More: include airplane mode, Ethernet, VPN, portable hotspot and mobile networks.
d) Sound: set the volumes, silent mode, default notification, touch sounds, and screen lock sound.
e) Display: set the brightness, wallpaper, auto-rotate screen, sleep, font size, accelerometer coordinate system,
screen adaption, and smart backlight.
f) Storage: query the total space, usage space and available space of system disk, and internal storage.
g) Battery: show the battery message and status.
h) Apps: query the downloaded apps, on SD card apps, running apps, and all apps.
i) Accounts & Sync: users can add an email account and manage accounts synced to the WFTT07-2.
j) Location Services: Google’s location service, location, and Google Search.
k) Security: set the screen lock, owner info, encrypt tablet, unknown sources, and others.
l) Language & Input: set the system default language, input methods, text-to-speech output and pointer speed.
m) Backup & Reset: backup or reset the WFTT07-2 data back to factory default.
n) Date & Time: automatic time zone or set by yourself, use 24-hour format and select data format.
o) Accessibility: set the system text size, auto-rotate screen, touch & hold delay, and install web scripts.
p) Developer Options: set USB debug, pointer location, show touches, and others.
q) About Tablet: information of system updates, status, version, and legal.

Page 2
STEP #2 –Wi-Fi Setup
In order to control your home, you will need to put your WFTT07-2 onto your WiFi network. Follow the instructions below
to connect this to your network.
a) Enter into the settings and
turn on the Wi-Fi.
b) Once the Wi-Fi list is
populated, select your Wi-Fi
network to connect to.
c) Enter the password when
prompted to.
d) Once the network says
‘Connected’, go to your app
drawer and open up
‘Browser’ to make sure you
are connected to the internet.
e) Once connected you can
proceed to setting up the
HSTouch Server & Client.
STEP #3 –HSTouch Server Setup
After you have successfully connected to your Wi-Fi network, you will need to make sure HSTouch Server is properly set
up before connecting the client to your HomeSeer system. This guide will assume that you have gone through the
necessary steps to set up HomeSeer. Follow the instructions below to set up HSTouch Server.
a) Go to the Plug-in’s menu within your HomeSeer Web Control and click on Manage.
b) If HSTouch Server is not installed follow these steps, otherwise skip to step f
c) Click on Additional Interfaces to expand the plug-in updater.
d) Scroll down to User Interfaces and expand that. Check the box next to HomeSeer HSTouch Sever.
e) Scroll back up and click on Download and Install.
f) Now that HSTouch Sever is installed we will need to enable it. Underneath the Enable column click on the red
toggle. It should become green with a check mark in it.
g) HSTouch Server is now enabled. You can now go into your WFTT07-2 to configure HSTouch.

Page 3
STEP #4 –HSTouch Client Setup
Here you will configure your settings and connect to your HomeSeer system to allow for control from your device. Follow
the instructions below to set up the HSTouch Client. To configure these settings on iOS, go to the Settings app and
scroll down to HSTouch and proceed with step b.
a) HSTouch will prompt you to select a
server or settings. Click settings. (The first
launch will require an initial setup.) A
menu on the bottom right will pop up.
Click Settings again. (This menu can also
be used to switch between servers, go to
settings, or exit the app.)
b) Within the settings you are given multiple
options. Servers 1-4 allow you to
configure each server for different
locations.
c) Select the server you would like to have
as your Home setup.
d) Configure a Label for that HomeSeer
system. Click Address to enter the IP
Address or Domain of the HomeSeer
System.
e) Now that you have set up the connection
address, go ahead and enter in your
Username and Password for that server.
There is no need to change the port.
f) You can follow steps c-e for the remaining
3 connections.
g) If you go back to the main settings
screen, there are other options for setting
up HSTouch.
h) Connection Mode allows you to choose a
default connection for each time you start
HSTouch. (HSTouch will no longer prompt
to choose a connection at the beginning.)
i) Dim Systembar allows for the bottom
systembar to be dimmed. Font Scaling
allows for changing the scaling factor.
j) Auto Size allows for auto-sizing of the
project being used for your device. Client
Name will allow you to change the name
of your device’s HSTouch Client. (For use
with HSTouch Designer). Zipcode is used
for weather.
k) Pressing the HomeSeer icon at the bottom brings up Voice Control.
l) Now that your Client has been set up, go back to the Main Screen and go to the settings menu on the bottom
right. Click Exit. Now go to your app drawer and click HSTouch. This will allow for any changes to take place.
m) You are now ready to control your home via your device!

Page 4
Setting Up MyHS
The next step involves going into the HSTouch application and entering in your Account Username and Account
Password.
a) Open up the HSTouch application. It will give you the same prompt as earlier to Log In to MyHS.
b) The email you used to register is your Username and the password you used will be used as the Password.
c) Click Ok and HSTouch will now connect.
d) HSTouch will now always connect through MyHS when launching. This will work from any location and any
network.
STEP #5 –Updating the HSTouch Client
HomeSeer will frequently put out updates to the HSTouch application. There are two methods available for updating the
app. Follow the instructions below to update your HSTouch app.
Method 1
a) Once connected to your system. Select the menu button on the bottom
right.
b) An option will show that says “Update #.#.# Available”. Click to update.
(Your menu will display ‘No Update Available if you are on the newest
version and no updates are available)
c) You will be prompted to click Install. Once finished you can click Done or
Open.
Method 2
a) The APK for the HSTouch Android app will be posted to the HomeSeer Message Board (board.homeseer.com).
You can go to the website via the WFTT07-2 and download the APK directly to the device. (typically this is a
BETA verison)
b) You can also download the APK to an SD card on a separate computer and then insert the SD card into the top
right side of the WFTT07-2.
c) Go to file manager and click on the SD card tab at the top. Select the HSTouch APK and begin the installation
procedure. Select update when prompted.

Page 5
Troubleshooting Your HomeTroller Zee
Symptom
Cause
Solution
Unit Won’t Power On
Ac Adapter Unplugged
Plug-In Adapter
AC Adapter Bad
Contact HomeSeer
Power Cable Bad
Unit Powers On But Won’t Boot
Software Failure
Contact HomeSeer
Hardware Failure
Contact HomeSeer
Wi-Fi Wont Connect
Invalid Username & Password
Double Check Wi-Fi Username &
Password.
Unable to Connect
Reset your router
HSTouch Won’t Connect
Wrong Address
Double check the IP. Use
find.homeseer.com to check the IP
Invalid Username & Password
Double check the Username &
Password for your HS system.
Factory Reset
Settings -> Backup & Reset -> Factory Data Reset -> Reset Tablet
HomeSeer Technologies
10 Commerce Park North, Unit #10
Bedford, NH 03110
www.homeseer.com
603-471-2816