Honeywell Esser 8010 User manual

798955.GB0
09.2007
G 200090
G 205064 Technical changes reserved!
GB
Operation and Installation Instruction
Extinguishing Control Computer 8010 – 19-Inch Design
(Series 2 and Series 3)

Extinguishing Control Computer 8010 – 19-Inch
2 FB 798955.GB0 / 09.07
Intended purpose
This software must only be used for the applications outlined in the catalogue and the technical description
and in combination with external components and systems which have been approved and /or
recommended.
Warning
In order to ensure correct and safe operation of the product, all guidelines concerning its transport, storage,
installation, and mounting must be observed. This includes the necessary care in operating the product.
Safety-relevant user information
This manual includes all information required for the proper use of the products described.
The term 'qualified personnel' in the context of the safety information included in this manual or on the
product itself designates:
•project engineers who are familiar with the safety guidelines concerning fire alarm and extinguishing
systems.
•trained service engineers who are familiar with the components of fire alarm and extinguishing systems
and the information on their operation as included in this manual.
•trained installation or service personnel with the necessary qualification for carrying out repairs on fire
alarm and extinguishing systems or who are authorised to operate, ground and label electrical circuits
and/or safety equipment/systems.
Safety warnings
The following information is given in the interest of your personal safety and to prevent damage to the
product described in this manual and all equipment connected to it.
Safety information and warnings for the prevention of dangers putting at risk the life and health of user and
maintenance personnel as well as causing damage to the equipment itself are marked by the following
pictograms. Within the context of this manual, these pictograms have the following meanings:
Warning sign
Designates risks for man and/or machine. Non-compliance will create risks to man and/or
machine. The level of risk is indicated by the word of warning.
Important information on a topic or a procedure and other important information!
This is an important guideline issued by VdS Schadenverhütung GmbH, Cologne.
If the hazard alarm system is programmed in compliance with VdS, this section must be read very
carefully and all instructions must be adhered to.
Dismantling
In accordance with Directive 2002/96/EG (WEEE), after being dismantled, electrical and
electronic equipment is taken back by the manufacturer for proper disposal.

Extinguishing Control Computer 8010 – 19-Inch
FB 798955.GB0 / 09.07 3
Table of contents
1General.......................................................................................................................................................................4
1.1 Accessories / Options..........................................................................................................................................4
2Display and control panel..........................................................................................................................................5
2.1 LED indicator for zones and outputs..................................................................................................................6
2.1.1 Status display of the zones............................................................................................................ 6
2.1.2 Status display of the outputs.......................................................................................................... 7
2.2 Operating displays...............................................................................................................................................8
2.3 Trouble displays.................................................................................................................................................10
2.3 Keypad functions...............................................................................................................................................12
2.4 Connect / disconnect zones..............................................................................................................................13
2.5 Connect / disconnect relay outputs..................................................................................................................14
2.6 Test mode ..........................................................................................................................................................15
2.7 Revision mode...................................................................................................................................................16
2.8 Resetting the panel............................................................................................................................................17
2.9 Lamp test............................................................................................................................................................17
3Control indicator and Alarm counter.......................................................................................................................18
4 Installation Instruction...............................................................................................................................................19
0786
Novar GmbH, Dieselstrasse 2, D-41469 Neuss
06
0786 - CPD - 20223
Designs
Series 2 (Part No. 788010 / 788011)
Series 3 (Part No. 788012 / 788013)
19 inch Series 2 (Part No. 788024 / 788025)
19 inch Series 3 (Part No. 788014 / 788015)
Environmental conditions category: A
Response time for activation status: maximum 3 seconds
Response time for activation of outputs: maximum 1 second
The facility can be equipped in various configuration levels (in terms of number, system type and extinguishing
range options).
Number of extinguishing ranges: 1
System type for the extinguishing range: High or low gas pressure, for use with the following extinguishing gases:
argon, CO2, FM200 (HCF-227EA), Inergen, Novec KD 1230, nitrogen, Trigon
Available options with requirements:
– Activation signal delay (Sect. 4.17); range 0 s to 60 s
– Signal that represents the flow of the extinguishing agent (Sect.. 4.18)
– Monitoring of the status / position of components (Sect. 4.19)
– Stop button (Sect. 4.20)
– Control of flooding times (Sect. 4.21); range 4 s to 600s
– Initiation of subsequent flooding (Sect. 4.22)
– Activation signals to devices within the fire extinguishing system (Sect. 4.24)
– Trigger signal to spare bottles (Sect. 4.25)
– Activation signals to devices outside the fire extinguishing system (Sect. 4.26)

Extinguishing Control Computer 8010 – 19-Inch
4 FB 798955.GB0 / 09.07
1 General
The Extinguishing Control Computer 8010 – 19-inch a fire alarm control panel with an integrated controller for
use in extinguishing systems and provides the connection of automatic fire detectors and Manual call points.
With a total of eight automatic detector zones and 30 connectable automatic fire detectors for each zone, it is
possible to monitor a single extinguishing area as defined by the VdS Guideline 2496.
In addition, five permanently assigned inputs are available for connecting technical zones of units, for example
the manual detector zone or the Emergency Stop zone. The required control functions can be realized with the
total of 13 programmable relay outputs.
A maximum of 100 additional outputs could be realised by using the optional esserbus®transponders.
The Extinguishing Control Computer 8010 can be directly connected to the analog loop of the fire alarm system
8000 / IQ8Control via the esserbus®communication transponder (Part No 808615). Up to eight Extinguishing
Control Computers can be operated on one loop with other loop devices, e.g. fire detectors or esserbus®
transponders. This enables up to eight individual extinguishing areas to be monitored via one analog loop.
The Extinguishing Control Computer 8010 - 19-Inch is programmed with the programming software LKDE from
version V02.00 or higher.
Any operation on the installed fire alarm system must only be carried out by authorised personal in
accordance with relevant safety procedures and in coordination with the emergency services.
VdS compliant fire alarm systems must be designed in accordance with VdS guidelines.
Additional and updated Informations
The described features, specifications and product related informations in this manual correspond to
the date of issue (refer to date on the front page) and may differ due to modifications and/or
amended Standards and Regulations of the System design, Installation and Commissioning.
Updated documentations and informations are available for comparison on the
www.esser-systems.de homepage.
esserbus®and essernet®are registered trademarks in Germany.
LED Indicator description
LED lights up
continuously LED flashes LED flashes yellow / red
1.1 Accessories / Options
Part. No. Type
788014.GB Extinguishing Control Computer 8010 series 3 – 19-inch design with operating panel (3HE)
788015 Extinguishing Control Computer 8010 series 3 – 19-inch design without operating panel (3HE)
788024.GB Extinguishing Control Computer 8010 series 2 – 19-inch design with operating panel (3HE)
788025 Extinguishing Control Computer 8010 series 2 – 19-inch design without operating panel (3HE)
788653 Terminal card for C-mounting rail incl. 50-pole D-SUB cable, length 1m
788654 Terminal card for C-mounting rail incl. 50-pole D-SUB cable, length 2m
808615 esserbus®communication transponder

Extinguishing Control Computer 8010 – 19-Inch
FB 798955.GB0 / 09.07 5
2 Display and control panel
All operations of the Extinguishing Control Computer can be carried out with the clearly arranged function keys.
The keys can be locked with the built-in key switch.
12345678
910111213
1
4
7
0
8
5
23
6
9
0 0 0 5
Relay (AE) 1
2
3
4
5
6
7
8
9
10
11
12
13
1 2 3 4 5 6 7
891011
Unlocked
Disconnection
Switchover Buzzer off
Lamp test
Zone
Output
Panel reset
On
Off
Test operation
Fan trouble
Common trouble
Emergency
operation
Power trouble
Battery trouble
Ground fault
Trouble 1
Blocking
Detector zone
Fire/Switch off/Trouble
In operation
Switching off
Test operation
Extra releasing 1
Outputs
Alarm
Emergency release
Extinguishing system
activated
Extinguishing system
enabled
Fig. 1: General view of the Display and control panel
1LED status indicators
2LED indicator ÎDetector zone display No.1 to No.8 and
Technical zones No. 9 to No. 13
or
Relay outputs No. 1 to No. 13
3Button to switch between LED indicators dfor zones/relays
Button >Buzzer off< to acknowledge the internal Buzzer
4Function keys
5Fault indicators
6Control indicator
7Key-switch to lock/unlock the operating keys
8Opening for Programming via Service PC
Connector must be sealed with dummy plug for ESD protection
9Alarm counter
10 Ten-button keypad
11 Arrow keys to scroll display information

Extinguishing Control Computer 8010 – 19-Inch
6 FB 798955.GB0 / 09.07
2.1 LED indicator for zones and outputs
The status of the corresponding zone or of the output is shown with the 13 LED. The status of the 13 zones is
shown in normal operation.
Switchover
With the key >Switchover<, it is possible to switch between indicating the zones or outputs
(Toggle operation).
12345678
9 10111213
Detector zone
Fire/Switch off/Trouble
Fig. 2: Zone displays
2.1.1 Status display of the zones
Detector zone no. 1 to no. 9 (yellow/red LED)
Off Normal operation,
Detector zone ready to signal
Lights up red Fire alarm of the detector zone no. 1 to 9
Flashes red First alarm indicator, the first alarm was triggered by this zone
Flashes yellow/red Test mode
Flashes yellow Trouble,
only restricted alarm readiness of the detector zone
On - yellow Switch-off,
the detector zone is switched off via the control panel
Twinkle yellow Input monitor,
the zone number was entered via the control panel keypad
Technical zone no.10 to no.13 (yellow LED)
Off Normal operation, technical zone is alarm-ready
Lights up yellow 1) Triggers the technical zone 10 to 13
2)
Switch-off. The technical zone was switched off. The yellow LED >Switch off< also
lights up.
Flashes yellow Trouble
Twinkle yellow Input check- the zone number was entered via the control panel keypad.

Extinguishing Control Computer 8010 – 19-Inch
FB 798955.GB0 / 09.07 7
2.1.2 Status display of the outputs
The status of the corresponding zone or of the output is alternatively indicated with the 13 LED. The status of
the 13 zones is shown in normal operation. The output indication is activated by pressing the >Switchover< key.
The green LED >Output< of the status display lits to confirm the activated output indication.
Switchover
With the key >Switchover<, it is possible to switch between indicating the zones or outputs
(Toggle operation).
Status display of the outputs is
switched on
123456 8
9 10111213
7
Detector zone
Fire/Switch off/Trouble
In operation
Switching off
Test operation
Extra releasing 1
Outputs
Alarm
Emergency release
Extinguishing system
activated
Extinguishing system
enabled
Fig. 3: Status display of the outputs (Example with Output No. 7)
Outputs no.1 to no.13 (yellow LED)
Off Normal operation, the output is in the resting state
Flashes Output failure
On Output deactivated
Twinkle Input check -the output number was entered via the control panel keypad
Disconnected or zones in trouble will not signal an alarm in case of an event!

Extinguishing Control Computer 8010 – 19-Inch
8 FB 798955.GB0 / 09.07
2.2 Operating displays
The coloured LED-indicators give a quick overview of the current state of the Extinguishing Control Computer
8010.
In operation
Switching off
Test operation
Extra releasing 1
Outputs
Alarm
Emergency release
Extinguishing system
activated
Extinguishing system
enabled
Fig. 4: Operating display
Operation (green LED)
On System ready for operation, keypad locked.
Flashes System ready for operation, keypad enabled for operation with the key switch.
Off Failure of the mains and emergency power supply.
Extinguishing system enabled (red LED)
On The connected extinguishing system has been enabled.
An evacuation time is started. After the evacuation time expires, release is initiated unless it is
stopped or prevented manually. The evacuation time is programmable between 1 to 255 seconds.
Extinguishing system activated (red LED)
On The enabled extinguishing system has been activated.
The flooding function is carried out and the extinguishing agent is released. Disconnection of the
activated extinguishing system is not possible.
Depending on the system configuration a new flooding may be carried out by pressing the extra
release button.

Extinguishing Control Computer 8010 – 19-Inch
FB 798955.GB0 / 09.07 9
Emergency Stop (yellow LED)
On An already triggered extinguishing procedure is stopped during the evacuation time by the
Emergency Stop zone 10.
An emergency stop button of this technical zone has been pressed.
Switch-off (yellow LED)
On Common disablement, at least one disablement was recognized.
Test operation (yellow LED)
On The test operation of an detector zone was activated.
The Test Mode function can only be activated one automatic detector zone no.1-8 at the same
time.
Flashes The revision mode for outputs has been activated. The function >Revision mode< is activated for
all outputs which have been programmed with the revision function.
Revision mode always has priority over the test mode in the display!
Extra releasing (green LED)
On The LED indicates that the post-flooding has been triggered by the manual detector zone
(if configured as a common detector zone) or the extra released zone no. 11 has been activated
after the flooding time.
Outputs (green LED)
On Indicates that an output has been triggered.
Additional information is given by the yellow LED in the status display of the outputs.
Alarm (red LED)
On Common fire Îat least one fire message was detected.

Extinguishing Control Computer 8010 – 19-Inch
10 FB 798955.GB0 / 09.07
2.3 Trouble displays
A precise determination of the failure is possible with the yellow LED of the trouble display. The LED >Trouble<
has the function of a common trouble display. This LED is always activated when at least one failure has been
identified in the system.
Fan trouble
Common trouble
Emergency
operation
Power trouble
Battery trouble
Ground fault
Trouble 1
Blocking
Fig. 5: Trouble displays
Trouble (yellow LED)
On Common trouble,
at least one failure in the panel has been identified.
Emergency Operation (yellow LED)
On When the system is in emergency operation e.g. due to a CPU-failure.
The Extinguishing Control Computer is functional only to a limited extent. Correct functioning is
no longer guaranteed due to the system fault.
Call maintenance-service immediately!
Mains trouble (yellow LED)
On When a mains voltage failure has been identified.
The LED is activated directly even if a mains failure message is programmed with a 15 minute
delay. The LED turns off automatically as soon as the battery fault is not present anymore.
Battery trouble (yellow LED)
On When a battery voltage failure has been identified.
The LED is activated directly even if a battery failure message is programmed with a 5 minute
delay. The LED turns off automatically as soon as the battery fault is not present anymore.