Honeywell DPS 8 User guide

- Dfl©m<eyw®flfl
DPS 8
SYSTEM
INSTALLATION
MANUAL
WCPU66LB
WMMU66LB
WIOUlOOA
WIOUlOOB
W10U66LA
58010048
GHALRIWARE l
58010048“500
REV
B
JUNE
1986
DIST. NCO,XAN

This
manual
has
been
prepared
to
serve
as
a
guide
for
Honeywell
personnel
to
install,
verify,
and
deinstail
a
DPS
8
System.
Each
Preinstallation
and
installation
Task
is
numerically
and
chronologically
listed
on
the
System
Checkpff
list,
providing
the
installer
with
a
synopticai
View
of
each
task
to
be
performed.
This
listing
is
printed
on
heavy
paper
and
is
found
immediately
after
the
Table
of
Contents.
After
the
Preinstallation
and
Installation
Tasks
have
been
identified,
classified,
and
listed,
they
are
defined
in
the
appropriate
section
of
the
System Installation manual.
Other features include instructions for unpackaging, unpacking,
inspection, cable routing, and connections. Power system checkout
procedures to help assure correct equipment operation and performance and
deinstallation
procedures
required
for
safe
disconnection
and
return
of
equipment are also included in this manual.
NOTICE
1F
REV B
The following notice is provided in accordance with the United States Federal
Communications Commission's (FCC) regulations:
Warning: This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instruction manual,
may cause interference to radio communications. The equipment manufactured after
October 1,1983 has been tested and found to comply with the limits for a Class A
computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed
to provide reasonable protection against such interference when operated in a
commercial environment. Operation of this equipment in a residential area is
likely to cause interference, in which case the user at his own expense will be
required to take whatever measures may be required to correct the interference.
This document and the information contained herein are confidential to and the
property of Honeywell Information Systems, Inc. and are made available only to
Honeywell employees for the sole purpose of maintaining Honeywell’s products.
This document, any cooy thereof and the information contained herein shall be
maintained in strictest confidence; shall not be copied in whole or in part
except as authorized by the employee’s manager; and shall not be disclosed or
distributed (a) to persons who are not Honeywell employees, or (b) to Honeywell
employees for whom such information is not necessary in connection with their
assigned responsibilities. Upon request, or when the employee in possession of
this document no longer has need for the document for the authorized Honeywell
purpose, this document and any copies thereof shall be returned to the employee's
manager. There shall be no exceptions to the terms and conditions set forth
herein except as authorized in writing by the responsible Honeywell Vice President.
58010048-011

RECORD OF REVISION
REV
DATE
AUTHORIZATIOfl
PAGES AFFECTED
12/85
6/86
PHAFPW988
PHAFPWSO?
RECORD OF REVISION
58010048-031.
58010048-012,
58010048-500
58010048-011,
58010048-041,
58010048-014,
58010048-035,
58010048-530,
58010048-010.
58010048-015,
58010048-051,
58010048, 3-1
58010048, 4-1
58010048, A-1
58010048-500
58010048-011.
58010048-014,
58010048-034,
58010048-035.
58010048-530,
58010048-010.
58010048-015.
58010048-051,
58010048, 3-1
58010048, 4-1
58010048. A-l
1F
1F
1F
1F
1F
1F
1, 2F
1F
1-1 THRU 1-3F
2-1F
THRU 3-16F
THRU 4-89?
58010048, 5-1F
THRU A-11F
1F
1F
1F
1F
1!
1?
1-1 THRU 1-3F
2-1, 262, 2-3F
THRU 3-16F
THRU 4-113F
2, BF
58010048, 5-1F
THRU A-15F
IF
I than-1mg
RECORD OF REVISION
REV B
REV
DATE
AUTHORIZATION
PAGES AFFECTED
58010048-014

REV 8
Revised
entire
manual
to
reflect
the
shielded
cable
versions
and
their
options.
SUMMARY
OF
CHANGES
1F
58010048-034

REV’ B
Honeywell Large Syatema Hardware @Uh?itat§aa;
P. G. Box 8000, MS cap
Phoenix, Arizona snoéemanon
i
-
“”"“
’”'W
'
geflgufia
e
{53010048
]
5
a
BPS
8
l
*fifiVISEOM
B
TITLEISYSTEM
INSTALLAIIQN
MAHUAL
;
‘
i
i
J
[
VDATED
[JUNE
1986
]
ERRORS IN PUBLICATION
SUGGESTIONS FOR IMPROVEMENT TO PUBLICATION
Your
comments
wlll
be
investigated
by
appropriate
technical
personnel
and
action
will
be
token
as
required.
Receipt
of
all
forms
will
be
acknowledced;
however,
if
you
requlre
a
detailed
reply,
check
here.
[::]
FROM:
NAME
DATE
TITLE
ADDRESS
PHONE #
USER
REMARKS
1F
58010048*035

HHHHHHHHH
GNOUIbUNO-‘O
O
BINDER.
SPINE (1-INCH)
SEPARATOR TABS ...................................... 58010048-012
TITLE PAGE
NOTICE
RECORD
OF
REVISION
.................................
58010048-014
SUMMARYOF CHANGES .................................. 58010048-034
USER REMARKS
TABLE
OF
CONTENTS
..................................
58010048-530
CHECKOFF LIST
GENERAL
PHYSICAL OUTLINE (TAB)
PREINSTALLATION
INSTALLATION
DEINSTALLATION
APPENDIX A
SECTION
B-SIZE. 4-RING, l-INCH (RED)
ooooooooooooooooooooooooooooooooooooooooooooo
O O O C O O IOC O . O O ‘8 Q .. 1" E f. - O i Q G l‘ 0 k‘ 0 v C 1 D - k‘ I 5555555
TABLE OF CONTENTS
58009984-00?
58010048-031
ooooooooooooooo
OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO
agazacfiam§.g
58010043-911
.......................................
58010048-035
58010048-010
58010048-015
58010048-051
58010048
58010048
58010048
58010048
OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO
OOOOOOOOOOOOOOOOOOOOOOOOOOOOO
00000000000000000000000000000
(TAB)
(TAB)
(TAB)
(TAB)
ooooooooooooooooooooooooooooo
ooooooooooooooooooooooooooooo
ooooooooooooooooooooooooooooo
OOOOOOOOOOOOOOOOOOOOOOOOOOOOO
DESCRIPTION .
GENERAL
.......................................................
INTRODUCTION
..................................................
PURPOSE
.......................................................
TOOLS
REQUIRED
................................................
TEST
EQUIPMENT
REQUIRED
.......................................
TEST
MEDIA
REQUIRED
...........................................
REFERENCE
DOCUMENTATION
.......................................
DOCUMENTATION
TREE
............................................
FEEDBACK
......................................................
PHYSICAL
OUTLINE
..............................................
PREINSTALLATION
TASKS
.........................................
TASK
TASK
TASK
TASK
TASK
TASK
TASK
TASK
1
2
3
4A
4B
5
6
7
TURN
T0
PREINSTALLATION
CHECKOFF
LIST
...............
SITE
INSPECTION
.....................................
RECEIVE
EQUIPMENT
...................................
UNPACKAGING
A
NONCRATED
PACK
.......................
UNPACKAGING
A
CRATED
PACK
...........................
UNPACKING
...........................................
INSPECT
EQUIPMENT
...................................
POSITION
CABINETS
.....................
v
..............
TABLE
OF
CONTENTS
2-1
3-1
3-3
3-5
3-7
3-9
3-10
3-11
3-13
3-15
REV B
SECTION
DESCRIPTION
PAGE
4.0
INSTALLATION..................................................
4-1
4.1
SCOPE.
........................................................
4-1
5.2
ELECTROSTATIC
DISCHARGE
.......................................
4—1
4.3
SYSTEfi
GROUND
.................................................
4-2
4.4
JOIN
CABINETS
.................................................
4-3
4.5
CABLE/HARNESS
ROUTING
OVERVIEW
FOR
DUAL
SYSTEM
................
4-4
4.6
CABLEIHARNESS
ROUTING
OVERVIEW
FOR
TANDEM
SYSTEM
..............
4—5
4.7
INSTALLATION
TASKS
............................................
4-6
TASK
1
TURN
TO
INSTALLATION CHECKOFF
LIST
..................
4-8
TASK
2
INSTALL
MMU
CABINET
.................................
4-10
TASK
3
INSTALL
CPU
CABINET
.................................
4-14
TASK
4A
INSTALL
IMU
CABINET
.................................
4-18
TASK
4B
INSTALL
IOM
CABINET............................
.....
4-22
TASK
5
INSTALL
DPU
CABINET
.................................
4-26
TASK
6
INSTALL
SYSTEM
CONSOLE
..............................
4-28
TASK
7
INSTALL
PORT
CABLES
AND
HARNESSES
..................
4-30
TASK
8
INSTALL
CABLES
FROM
IOM/IMU
TO
PCM
CONTROLLERS
.....
4-46
TASK
9
INSTALL
IIO
CABLES
..................................
4-56
TASK
10
INSTALL
AC
POWER
CABLES
.............................
4-96
TASK
11
ACTIVATE
AND
CHECK
POWER
SYSTEM
.....................
4-98
TASK
12
INSTALL
LOWER
TRIM
STRIPS
...........................
4-106
TASK
13
CONFIGURE
CENTRAL
SYSTEM
............................
4-108
TASK
14
TEST
TAC
REMOTE
CONNECTIONS
.........................
4-110
TASK
15
FUNCTIONAL
VERIFICATION
TESTS
.......................
4-112
5.0
DEINSTALLATION
................................................
5-1
APPENDIX
A
-
IMU
CONFIGURATOR
........................................
A-l
58010048-530

~ru-usau-u~au-q~au<ruvb\»NIo-u
I
q
I
#-
4h9h{Obi-55:375.:«b:tP-I-IDLPD-
«It
{#75
957%
3‘
"Citah-bub
whack
hl-b
-&
ab ‘-
35
#7
DI
&
'75
It
JD
«5
b
b
b
b
N
70-0
FIGURE
IIIIIII
I
AHHOGN0U=5UN‘HH‘HH-HHHH
I
Q
I
hLH
SuTurro
N
I
ah
.7-15
.7-1Q
.7— I7
.7 1Q
.7-17
~77§Q
7-177
.7 77
.7— 23
.7« 74
-3 35
.7-7O
.Zégl
7-73
.7- -29
.7 3O
.7-31
.7-72
.7- 37
-7-21
LIST OF ILLUSTRATIONS
TITLE PACE
OPS
a
DOCUMENTATION
TREE
....................................
1-3
PHYSICAL
OUTLINE
............................................
2-1
ELECTROSTATIC
DISCHARGE
WRIST
STRAP
APPLICATION
.............
4-1
TOP
VIEW
OF
SYSTEM
CROUNO
AREA
IN
MMU
CABINET
...............
4-2
JOINING
CABINETS
TOGETHER
...................................
4-3
OUAL
SYSTEM
CABLE/HARNESS
ROUTING
..........................
4-4
TANOEM
SYSTEM
CABLE/HARNESS
ROUTING
........................
4-5
POSITION MMU CABINET ........................................ 4-11
MMU
CABINET
-
CIRCUIT
BOARO
LOCATION
........................
4-12
MMU
CABINET
-
PONER
PANELS
..................................
4-13
POSITION CPU CABINET ........................................ 4-15
CPU
CAOINET
-
CIRCUIT
OOARO
LOCATION
........................
4-16
CPU
CABINET
-
PONER
PANELS
..................................
4—17
POSITION IMU CABINET ........................................ 4-19
IMU CAQINET - CIRCUIT ROARO LOCATION ........................ 4-20
IMu
CABINET
-
POWER
PANELS
..................................
4-21
POSITION
IOM
CABINET
........................................
4-23
IOM
CABINET
-
CIRCUIT
BOARO
LOCATION
........................
4-24
IoM
CABINET
-
PONER
PANELS
..................................
4-25
POSITION OPU CABINET ........................................ 4-27
POSITION
SYSTEM
CONSOLE
.....................................
4-29
INSTALL CACHE CABLE ......................................... 4—31
INSTALL ACTIVE PORT CABLE ................................... 4-32
INSTALL WIPGQQLH OOS O PORT CABLE ........................... 4-33
INSTALL WIPOQQLH Bus I 9987 CAOLE ........................... 4-34
INSTALL NIPOOOLJ OOS O PORT CABLE ........................... 4-35
INSTALL
ACTIVE
PORI
CABLE
...................................
4-36
IN$TALL
IOM
PORT
CARLE........................
..........
....
4-37
TYPICAL MULTIOROP CABLE ROUTINE ............................. 4-33
INSTALL
NIPOO4LN
Bus
O
SNIELOEO
PORT
CABLE
..................
A-Az
INSTALL NIPOOILI OUS O SNIELOEO PORT CABLE .................. 4-44
INSTALL CABLES PROM IOM/IMU TO PCM CONTROLLERS .............. 4-47
PSIA 2- -TOIP CABLINC ......................................... 4-57
PSIA A-IRIP CAOLINC ......................................... 4-59
NEN OIRECT INTERFACE CHANNEL CABLINS ........................ 4-50
OISK OAU DEVICE ADAPTER CABLINC................. ............ 4-O2
OISK OAU OEVICE ADAPTER CABLINC ............................. 4-54
OISK OAU OEVICE INTERFACE CABLINC ........................... 4-66
OEVICE AOAPTER INTERFACE CABLINC ............................ 4-68
PERIPHERAL DEVICE SERIAL INTERFACE CAOLINO .................. 4-69
HIGH SPEED NCHOOIIO PSIA CABLING ............................ 4-70
TABLE OF CONTENTS
I##b&&&w§h&&b&h«bbhfiw&&h
FIGURE
.7*35
.7’36
.7‘37
.7“38
.7“39
.7-40
.7-41
.7-42
.7“43
.7-44
.7-45
.7-46
.7‘47
.7-48
.7-49
.7-50
.7-51
.7-52
.7~53
.7~54
REA! B
LIST OF ILLUSTRATIONS
TITLE PAGE
STANDARD SPEED PSIA CABLING ................................. 4-72
DIRECT CHANNEL CABLING ...................................... 4-73
HIGH SPEED WCHOO4ID PSIA CABLING ............................ 4-75
EURCB BOARD OPTIONS ......................................... 4-77
UR PERIPHERAL DEVICE SERIAL INTERFACE SHIELDED CABLING ...... 4-81
UR DAI SHIELDED CABLING.' .................................... 4*82
PSIA 2-TRIP SHIELDED CABLING ................................ 4-83
PSIA 4-TRIP SHIELDED CABLING ................................ 4-85
NEW DIRECT INTERFACE CHANNEL SHIELDED CABLING ............... 4-86
DISK DAU SHIELDED CABLING ................................... 4-88
DISK DAU DEVICE INTERFACE SHIELDED CABLING .................. 4-90
ADDITION DATA CHANNEL SHIELDED CABLING ...................... 4*92
IMU BULKHEAD CONNECTIONS .................................... 4-94
AC POWER ENTRY .............................................. 4-97
CONSOLE - EMERGENCY OFF SWITCH .............................. ‘-100
MMU CABINET - POWER PANELS .................................. 4-101
CPU CABINET - POWER PANELS .................................. 4-102
IMU - POWER PANELS .......................................... 4-103
IOM CABINET - POWER PANELS .................................. 4-104
INSTALL LOWER TRIM STRIPS ................................... 4-107
58010048-530

TABLE
>I>é-blsh.h¢-h
A2.
A2.
A3.
A3.
A4.
A4.
A5.
A5.
A5.
A5.
A5.
A5.
A5.
A5.
A5.
A5.
A5.
-\l\JV~J\JO‘Ul
DC)!
II
I
llmhuNHHI—I
NH
LIST OF TABLES
TITLE
DUAL SYSTEM - CABLEiHARNESS ROUTING .........................
TANDEM SYSTEM - CABLE/HARNESS ROUTING .......................
INTERCABINET UNSHIELDED CABLING .............................
TYPICAL PLUG COMPATIBLE MANUFACTURER (PCM) CABLE ROUTING....
UNSHIELDED I/O CABLING ......................................
SHIELDED IIO CABLING ........................................
CONFIGURATION CHART .........................................
CHANNEL BOARD SLOT REQUIREMENTS .............................
IMU CARD CAGES O (CHANNEL ADAPTERS/IPCS)
AND 1 (IPU CENTRAL) .........................................
IMU CARD CAGES 2 (CHANNEL ADAPTERS/IPCS)
AND 3 (IPU CENTRAL) .........................................
VALID SETS OF LC NUMBERS ....................................
BACKGROUND CONFIGURATION LIMITS .............................
TAPE AND DISK DATA BUFFERING ................................
DISK AND TAPE LOADING COMBINATIONS. DPS 8 52/70 SYSTEMS .....
'PRIORITY SEQUENCE AND LOAD FACTORS ..........................
SAMPLE CONFIGURATION, DPS 8 52/70 SYSTEM ....................
BOARD CAPACITY OF ONE 19*CARD CAGE
USING THE 2-BOARD TTL PSIA-Z ................................
BOARD CAPACITY OF ONE 19-CARD CAGE
USING THE l-BOARD CMOS PSIA~2 ...............................
TYPICAL POWER CONSUMPTION BY OPTION .........................
POWER NEEDED BY STANDARD IMU CENTRAL ........................
POWER NEEDED BY STANDARD DAU ................................
CONNECTABILITY MATRIX, NO DAUS, TTL PSIA-Z,
TWO 19-CARD CAGES (TOTAL CAPACITY) ..........................
CONNECTABILITY MATRIX, NO DAUS, CMOS PSIA-Z,
TWO 19-CARD CAGES (TOTAL CAPACITY) ..........................
CONNECTABILITY MATRIX, ONE DAU, TTL PSIA-Z.
TWO 19-CARD CAGES (TOTAL CAPACITY) ..........................
CONNECTABILITY MATRIX, ONE DAU. CMOS PSIA-Z.
TWO 19-CARD CAGES (TOTAL CAPACITY) ..........................
CONNECTABILITY MATRIX, TWO DAUS, TTL PSIA-Z.
TWO 19-CARD CAGES (TOTAL CAPACITY) ..........................
CONNECTABILITY MATRIX, TWO DAUs, CMOS PSIA-Z,
TWO 19-CARD CAGES (TOTAL CAPACITY) ..........................
TABLE OF CONTENTS
PAGE
4-4
4-5
$~45
4—54
A-vq
4-95
4-109
A—1
A-z
A—2
A-4
A~5
A-7
A—a
A-IO
A-lO
A—11
A-11
A-12
A-12
A-12
A—13
A-13
A-14
A-14
A-ls
A-15
3F
REV B
58010048*SBO

CHECKOFF
LISTS
PREINSTALLATION
CHECKOFF
LIST
TASK
NO.
4A.
4B.
CHECKOFF LIST
TASK
PERFORMED
TASK
TITLE
BY
TURN
TO
PREINSTALLATION
CHECKOFF
LIST
SITE INSPECTION
RECEIVE
EQUIPMENT
UNPACKAGING
A
NONCRATED
PACK
UNPACKAGING
A
CRATED
PACK
UNPACKAGING
INSPECT
EQUIPMENT
POSITION CABINETS
TASK
CHECKED
BY
1F
TASK
NO.
4A.
4B.
10.
11.
12.
13.
14.
15.
INSTALLATION
CHECKOFF
LIST
TASK TITLE
TURN TO INSTALLATION
CHECKOFF LIST
INSTALL MMU CABINET
INSTALL CPU CABINET
INSTALL IMU CABINET
INSTALL IOM CABINET
INSTALL DPU CABINET
INSTALL SYSTEM CONSOLE
INSTALL PORT
CABLES AND HARNESSES
INSTALL
CABLES
FROM
IOM/IMU
TO
PCM
CONTROLLERS
INSTALL IIO, PORT, AND
SYSTEM CONSOLE CABLES
INSTALL AC POWER CABLES
ACTIVATE
&
CHECK
POWER
SYSTEM
INSTALL LOWER TRIM STRIPS
CONFIGURE
CENTRAL
SYSTEM
TEST TAC REMOTE CONNECTIONS
FUNCTIONAL VERIFICATION
TASK
PERFORMED
BY
TASK
CHECKED
BY
REV B
58010048—010

1.0 GENERAL
This
manual
has
been
prepared
to
serve
as
a
guide
for
the
Customer
Services
Engineer
(CSE)
to
insteii
or
deiusteil
the
DPS
a
system.
The
CSE
should
be
familiar
with
each
section
of
this
manual
and
the
Options
Installation
Manual
prior
to
installation.
Refer
to
the
System
Options
Manual,
58010049,
for
options
installation
instructions.
This
manual
does
not
include
installation
or
deinstallation
instructions
for
peripheral
devices,
peripheral
device
controllers,
or
auxiliary
processors
such
as
those
performing
front-end
processing
functions.
1.1 INTRODUCTION
This
manual
is
divided
into
the
following
sections:
SECTION 1 GENERAL
This
‘section
contains
an
introduction
to
the
manual,
including
an
overview
of
the
DPS
8
field
documentation
structure.
SECTION
2
PHYSICAL
OUTLINE
This
section
contains
an
illustration
of
the
three-cabinet
system.
SECTION
3
PREINSTALLATION
This
section
includes
procedural
steps
or
TASKS
for
receiving,
handling,
unpackaging,
unpacking,
inspection,
and
placement
of
cabinets.
SECTION 4 INSTALLATION
This
section
provides
procedural
steps
or
TASKS
to
install
the
equipment.
SECTION 5 DEINSTALLATION
This
section
includes
deinstallation,
handling,
and
shipping
procedures.
GENERAL
RE\/ 8
1.2 PURPOSE
in addition to the CSE, this manual will 'also be useful to Customer
Services
Training
for
classroom
studies
and
for
field
study
reference,
Training will usually be supported with additional instruction material;
however;
the
student
should
use
this
document
as
primary
reference.
This
manual can also be used for remote field support and should be included in
the
Technical
Assistance
Center
(TAC)
library.
1.3 TOOLS REQUIRED
standard tool kit 71001001-001 is
For a listing of DPS 8 system tools,
The Customer Services Department
required to install this system.
refer to System Tools List, 58059036.
1.4 TEST EQUIPMENT REQUIRED
Standard test equipment.
1.5 TEST MEDIA REQUIRED
o Off—Line T and D System Tape (Pas 2/Monitor)
0 System Acceptance Test Tape (IMCV)
0 Integrated Firmware and Diagnostic Tape
0 NFT Diskettes
58010048-015