manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Honeywell
  6. •
  7. Microcontroller
  8. •
  9. Honeywell GENT VIG-MCC-24 Instruction manual

Honeywell GENT VIG-MCC-24 Instruction manual

Popular Microcontroller manuals by other brands

Microsemi IGLOO nano Starter Kit user guide

Microsemi

Microsemi IGLOO nano Starter Kit user guide

GOWIN DK START GW1NSR-LV4CQN48PC7I6 V 1.1 user guide

GOWIN

GOWIN DK START GW1NSR-LV4CQN48PC7I6 V 1.1 user guide

HETRONIC ERGO-S Service manual

HETRONIC

HETRONIC ERGO-S Service manual

Laird BL654PA user guide

Laird

Laird BL654PA user guide

Novatek NT6861 manual

Novatek

Novatek NT6861 manual

Lantronix Intrinsyc Open-Q 865XR SOM user guide

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM user guide

Nuvoton ISD61S00 ChipCorder Design guide

Nuvoton

Nuvoton ISD61S00 ChipCorder Design guide

STMicrolectronics ST7 Assembler Linker user manual

STMicrolectronics

STMicrolectronics ST7 Assembler Linker user manual

Texas Instruments Chipcon CC2420DK user manual

Texas Instruments

Texas Instruments Chipcon CC2420DK user manual

NEC 78GK0S/K 1+ Series Application note

NEC

NEC 78GK0S/K 1+ Series Application note

Mikroe SEMITECH N-PLC Click Application note

Mikroe

Mikroe SEMITECH N-PLC Click Application note

Intel Agilex user guide

Intel

Intel Agilex user guide

DIGITAL-LOGIC MICROSPACE manual

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE manual

Texas Instruments TMS320F2837 D Series Workshop Guide and Lab Manual

Texas Instruments

Texas Instruments TMS320F2837 D Series Workshop Guide and Lab Manual

CYPRES CY14NVSRAMKIT-001 user guide

CYPRES

CYPRES CY14NVSRAMKIT-001 user guide

Espressif Systems ESP8266EX Programming guide

Espressif Systems

Espressif Systems ESP8266EX Programming guide

Abov AC33M8128L user manual

Abov

Abov AC33M8128L user manual

Silicon Laboratories C8051F800 user guide

Silicon Laboratories

Silicon Laboratories C8051F800 user guide

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.

This leaflet covers the Main Control(ler) Card
(VIG-MCC-24) which is designed for installation in
VIG1-24 and VIG1-72 Vigilon panels.
Technical data
Overall size 157mm height x 100mm width
Weight 96g (approximate)
Lithium Battery CR2032 3V cell.
Replace the battery only with
the same or equivalent type.
Dispose of all used batteries
according to the
manufacturer’s instructions.
Operating
temperature
0°Cto45°C
Storage
temperature
-10°Cto55°C
Relative humidity
(non condensing)
up to 90%
Battery connection
The MCC has a battery insulation sleeve or disk
that must be removed before the card is fitted in the
backplane.
&Once the battery insulation sleeve or
disk is removed from the MCC, the card MUST
NOT be placed on a metal surface as this may
result in damage to the components on the card.
Backplane
The MCC card must be installed in the correct
location in the backplane.
"An IO Card is not required for the connection
of DKC and Commissioning tool. The DKC ribbon
cables now connects to P2 and P4 on the MCC and the
Commissioning tool connect to the USB port on MCC.
&When handling the card always use
anti-static work procedures.
&Always ensure the panel is completely
powered down before removal or fitting of cards
into the backplane. Power down the battery supply
before the mains supply. The power up should be
done in a reverse order.
4188-906_issue 2_02/09_new MCC 1
Data and Installation
Main Control Card
(VIG-MCC-24)
by Honeywell
BATT1
Lithium battery + side up
Remove insulation sleeve or
disk before installing the card
SW1
USB port
to accept
commissioning
tool connectio
n
P2 socket to accept a
20-way ribbon
cable from the DKC
P4 socket to accept a
40-way ribbon
cable from the DKC
MCC card fits into the Backplane
slot marked P1 (MCC/LCC)
Reset
Switch
Chip
2211-143
V4.xx
Minimum
should be
V4.37
Master Controller Card (MCC)
to be fitted to socket
P1 CARD 0 on backplane
Secure the two ribbon
cables (at the fold) under the clamp
located on the backplane
40 way ribbon
20 way ribbon
Card guides
B
ac
k
p
l
ane
Main Controller Card or
Local Controller Card (SUPPLIED)
Network or IO Card (Optional)
Loop Processor Card (SUPPLIED)
or RS232
Loop Processor Card or RS232
(Option)
Loop Processor Card or RS232
(Option)
Loop Processor Card or RS232
(Option)
Network or RS232 or
Loop Card#
Network or RS232 or
Loop Card#
#for VIG1-72 only
P1 CARD 0
P2 CARD15
P3 CARD 1
P4 CARD 2
P5 CARD 3
P6 CARD 4
P7 CARD 5
P8 CARD 6
Backplane
Use the USB port on
the MCC to connect to
the Commissioning tool.
This page has been intentionally left blank.
Installation MCC
Gent by Honeywell reserves the right to revise this publication from time to time and make changes to the content hereof without
obligation to notify any person of such revisions of changes.
Hamilton Industrial Park, Waterside Road, Leicester LE5 1TN, UK Website: www.gent.co.uk
Telephone: +44 (0) 116 246 2000 Fax (UK): +44 (0)116 246 2300
2 4188-906_issue 2_02/09_new MCC
by Honeywell
At the end of their useful life, the packaging,
product and batteries should be disposed of
via a suitable recycling centre and in
accordance with national or local legislation.
Do not dispose of with your normal household waste.
Do not burn.
WEEE Directive:
At the end of their useful life, the packaging,
product and batteries should be
disposed of via a suitable recycling centre.