+1 800 323 4576 (North America only)
Document 800-25042 – Rev A – 05/2019
© 2019 Honeywell International Inc. All rights reserved. No part of this publication may be
reproduced by any means without written permission from Honeywell. The information in this
publication is believed to be accurate in all respects. However, Honeywell cannot assume
responsibility for any consequences resulting from the use thereof. The information contained
herein is subject to change without notice. Revisions or new editions to this publication may be
issued to incorporate such changes. For patent information, see www.honeywell.com/patent.
www.honeywell.com/security
WARNING
Cautions and Warnings
To ensure compliance with electrical safety standards,
CSA Certified/UL Listed LPS or Class 2 power adapters are required. Power
over Ethernet (PoE) shall be provided by listed Information
Technology Equipment meeting the IEEE 802.3af PoE standard. The
PoE is not intended to be connected to exposed (outside plant)
networks.
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
Honeywell
Manufacturer's Declaration of Conformance
Waste Electrical and Electronic Equipment (WEEE)
The manufacturer declares that the equipment supplied with this guide is compliant
with the European Parliament and Council Directive on the Restrictions of the use of
certain hazardous substances in electrical and electronic equipment (2011/65/EU),
General Product Safety Directive (2001/95/EC), and the essential requirements of the
EMC Directive (2014/30/EU), conforming to the requirements of standards EN 55032 for
emissions, EN 50130-4 for immunity, and EN 62368-1 for electrical equipment safety.
Correct Disposal of this Product (applicable in the European Union and other
European countries with separate collection systems).
This product should be disposed of, at the end of its useful life, as per applicable
local laws, regulations, and procedures.
Important Safeguards
Read and keep these instructions.
Please ensure that your installation area can safely support the weight of the camera.
Do not aim the camera toward a bright light source for extended periods to prevent
damage to the imager. Avoid operating the unit under or close to unstable light sources
(may cause flickering), or close to fluorescent lamps or objects reflecting light.
Do not touch the camera lens.
Do not drop the camera or subject it to physical shock.
Do not use a strong or abrasive detergent when cleaning the camera.
Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments,
where the operating temperature is outside the recommended range of -22°F to 140°F
(-30°C to 60°C).
Avoid operating the unit close to sources of powerful electromagnetic radiation, such as
radio or TV transmitters.
If powered by a power adapter, the adapter should be properly grounded.
Consult Honeywell for the recommended adapter or check it in Honeywell DOC.
Regulatory Statements
FCC Statement of Compliance
Information to the User: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Note Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Logging On to the Camera
If logging on the camera remotely from a PC, install the Honeywell Config Tool
from the software and documentation CD, find the camera on the network, and
then open the web browser with the Honeywell Config Tool. The default user
name is admin (case-sensitive) and the default password is 1234.
Note Internet Explorer 11 (or later) with ActiveX plug-in is supported.
Chrome 71 (or later) is supported for H.264 video. Chrome is not supported for
H.265 video.
IP address of the device is assigned automatically by DHCP server. If the DHCP
server is not available, the device will acquire 192.168.1.108 as the default IP
address.
Adjusting the Zoom and Focus Settings
After you have logged on to the camera, go to Camera Setup →Properties → Focus
to fine-tune the camera’s zoom and focus settings.
HC30WB5R2
Support Brackets
HBS2-BB Junction Box
Pole MountHQA-PM2 with HBS2-BB
