Honeywell HCCM674M User manual

User Guide
HCCM674M
High Resolution Day/Night
Miniature Box Camera
Document 800-11199 – Rev E – 09/2012

2www.honeywellvideo.com
WARNING To prevent the risk of fire or
electric shock hazard, do not expose this
camera to rain or moisture.
Information to the User: This equipment has been
tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protec-
tion against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interfer-
ence, in which case the user will be required to correct
the interference at his own expense.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This Class A digital apparatus complies with Canadian
ICES-003. Cet appareil numérique de la Classe A est
conforme à la norme NMB-003 du Canada.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DO NOT OPEN
RISK OF ELECTRIC SHOCK

800-11199 - E - 09/2012 3
Safety Instructions 1
Read Instructions
Read all of the safety and operating instructions before
using the product and retain them for future reference.
Cleaning
Turn off the power and clean with a dry, soft cloth.
Do not use liquid cleaners or aerosol cleaners.
Attachments
Do not use attachments not recommended by the
manufacturer as doing so may result in fire, electric
shock, or serious injury.
Water and Moisture
Do not use this product near water or moisture.
Mounting
Follow the manufacturer’s instructions when mounting
the product. Use only mounting accessories
recommended by the manufacturer.
Power Sources
This product should be operated only from the type of
power source indicated on the marking label. If you are
not sure of the type of power supplied to your facility,
consult your equipment dealer or local power
company.
Ventilation
Do not block any ventilation openings. Install in accor-
dance with the manufacturer’s instructions to ensure
reliable operation of the product and to protect it from
overheating.
Servicing
Do not attempt to service this product yourself. Refer all
servicing to qualified service personnel.

4www.honeywellvideo.com
Precautions 1
Operating
Before using the camera, make sure the power supply
and video output are properly connected. When
operating the camera, if any abnormal condition or
malfunction is observed, stop using the camera
immediately and call your equipment dealer.
Handling
Do not disassemble the camera. Never touch the
internal parts of the camera.
Do not drop the camera or subject it to shocks and
vibrations.
When attaching or removing the lens, take care that no
moisture or dust enters the camera body.
Avoid viewing bright objects (such as light fixtures) for
extended periods, or bright vertical and horizontal lines
may appear on the screen.
Installation and storage
Do not point the camera at the sun as this could
damage the camera whether it is operating or not.
Do not install the camera where the temperature could
exceed the allowable range. Make sure the ambient
temperature is less than 104°F (40°C) in installations
intended for long term continuous operation.
Avoid installing or storing the camera in locations where
the camera may be exposed to:
• water/rain
• humidity
•dust
•radiation
• mechanical vibrations
• strong magnetic fields and electrical signals
Daily check
To maintain proper operation for surveillance use,
check the camera output every day for a clear and
focused picture.

800-11199 - E - 09/2012 5
Contents 1
Safety Instructions . . . . . . . . . . . . . . 3
Precautions . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . 6
Camera Parts Explained . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . 10
Lens Installation. . . . . . . . . . . . . . . 10
Mounting a Lens . . . . . . . . . . . . . . 10
Back-focus Adjustment . . . . . . . . . . . 11
Suitable Lenses . . . . . . . . . . . . . . . 12
Camera Installation . . . . . . . . . . . . . 13
Connections . . . . . . . . . . . . . . . . 14
Menu System . . . . . . . . . . . . . . . . . 15
Menu Description . . . . . . . . . . . . . . . 16
Setup Menu . . . . . . . . . . . . . . . . . 17
Lens . . . . . . . . . . . . . . . . . . . . . 17
Shutter/AGC . . . . . . . . . . . . . . . . 18
White Balance. . . . . . . . . . . . . . . . 19
Backlight . . . . . . . . . . . . . . . . . . 20
Picture Adjust . . . . . . . . . . . . . . . . 21
ATR . . . . . . . . . . . . . . . . . . . . . 21
Motion Detection . . . . . . . . . . . . . . 22
Privacy . . . . . . . . . . . . . . . . . . . 23
Day/Night . . . . . . . . . . . . . . . . . . 24
Noise Reduction . . . . . . . . . . . . . . 26
Camera ID. . . . . . . . . . . . . . . . . . 26
Sync . . . . . . . . . . . . . . . . . . . . . 27
Language . . . . . . . . . . . . . . . . . . 28
Camera Reset . . . . . . . . . . . . . . . . 28
Save All . . . . . . . . . . . . . . . . . . . 28
Specifications . . . . . . . . . . . . . . . . 29

6www.honeywellvideo.com
Features 1
High sensitivity 1/3″CCD with on-chip micro lenses
and low-noise digital signal processing circuit provides
sensitivity down to 0.1 lux at F1.2, 50 IRE.
High-quality image Horizontal resolution of 650 TVL.
Digital signal processing with optimization of control
program and image correction algorithm.
BLC/HLC When strong light enters the scene back-
ground (such as from a spotlight or window), backlight
compensation automatically adjusts the video level to
preserve visibility. Highlight compensation masks
bright spots in a scene.
White balance Seven user-selectable white balance
control modes for varying conditions.
Iris function Drive output for video iris and DC iris
lens. Built-in electronic shutter allows eight shutter
speeds up to 1/100,000 s. CCD iris function automati-
cally sets picture brightness by changing the shutter
speed of the camera according to the incident light
when using a manual iris lens.
Other functions
• Camera ID of up to 24 characters
•Noisereduction
•4motiondetectionzones
• 4 privacy zones
• Picture adjustment for mirror, brightness, contrast,
sharpness, hue, and gain
• 24 V AC or 12 V DC power source
• C or CS mount lenses

800-11199 - E - 09/2012 7
Camera Parts Explained 1
Honeywell HCCM674M
Lens mount
Use when installing the lens. C-mount lens
uses a C-mount adapter. CS-mount lens
does not need a C-mount adapter.
Back-focus screw
Use to adjust the back-focus. See page 11.
Lens mount cap
Use to cap the lens mount
when the lens is not attached.
C-mount adapter
Use to install a C-mount lens.
Remove to install a CS-mount lens.
Turn counterclockwise to remove.
See page 10.
1/4-20 UNC Mounting Hole
Use to install the camera to a
tripod.
1/4-20 UNC Mounting Hole
Use to install the camera to a
tripod.

8www.honeywellvideo.com
12VDC/24VAC
CLASS2
GND
~~
VIDEO
LENS
LL INT
SET
INT/LL switch
INT: Internal sync mode
LL: Line lock sync mode
Setup buttons
Set up and adjust the camera using the
on-screen menu. See page 16.
Lens connector
Use to connect the lens cable when
using an auto-iris lens.
Video output connector
Connector a BNC connector that
outputs a composite video signal.
Power indicator
Lights up when the camera is
powered.
Alarm output connector
Factory use only.
Power input terminal
Connect to a 24 V AC or 12 V DC power source.
Do not connect the power source until all other
connections have been completed.

800-11199 - E - 09/2012 9
Lens Connector
When using an auto-iris lens, install the accessory lens
plug onto the lens cable as shown below.
Video Type Lens
1. Set the lens type to VIDEO.
2. Connect the lens cable of a video type lens. If the
plug on the cable is of a different type, replace it
with the supplied 4-pin iris plug.
DC Type Lens
1. Set the lens type to DC.
2. Connect the lens cable of a DC (galvanometric)
type lens. If the plug on the cable is of a different
type, replace it with the supplied 4-pin iris plug.
3. After installing the connector plug, connect it to
the lens connector on the rear panel of the
camera.
1
2 4
3
Pin Assignment Pin Signal
1 +12 V DC (50 mA max)
2 NC (not connected)
3 Video (0.7 Vp-p, high
impedance, no sync)
4GND
+12V
NC GND
Video input
13
42
Pin Signal
1Dampingcoil(–)
2Dampingcoil(+)
3Drivecoil(+)
4Drivecoil(–)
13
42
1
2 4
3
Damping coil (–) Drive coil (+)
Damping coil (+) Drive coil (–)
Pin Assignment

10 www.honeywellvideo.com
Installation 1
Lens Installation Mounting a Lens
1. Remove the lens mount cap from the camera.
2. Attach or remove the C-mount adapter,
depending on the lens to be used.
If necessary, use long-nosed pliers to remove the
C-mount adapter. Insert the tips of the pliers into
the holes with no threads, then turn until the
adapter comes loose.
You can also use a screwdriver by inserting M3
screws into the holes so that the screwdriver has
something to grip.
Store the C-mount adapter for future use.
3. Attach and secure the lens to the lens mount.