Honeywell HD4VC4HR User manual

User Guide
Vandal Fixed
Dome Camera
Document 900.0556 – 01/06 – Rev 1.02
NTSC / PAL
ItalianoDeutsch PortuguêsNederland EnglishEspañol Français
HD4VC4HR HD4VC4HRX

Rev 1.02 ii Document 900.0556
01/06
Revisions
Issue Date Revisions
1.00 06/05 New document, based on 900.0382.
1.01 08/05 Added WEEE Directive on page iii.
1.02 01/06 Corrected figure 5, Gimbal Adjustment to add setscrew
locations and explain how to adjust Horizontal and Pan rotation.

Rev 1.02 iii Document 900.0556
01/06
Warnings
Installation and servicing should be performed only by qualified and experienced
personnel to conform to all local codes and to maintain your warranty.
WARNING! The use of CSA Certified/UL Listed Class 2 power adapters is
required to ensure compliance with electrical safety standards.
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product
(applicable in the European Union and other European countries with separate collection
systems). This product should be disposed of, at the end of its useful life, as per applicable
local laws, regulations, and procedures.
Explanation of Graphical Symbols
This symbol indicates the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
This symbol indicates the presence of important operating and mainten-
ance (servicing) instruction in the literature accompanying the product.
that important operating
electric shock is present
ctions accompany
This symbol indicates
and maintenance
instru
this unit.
This symbol indicates
that dangerous voltage
constituting a risk of
within this unit.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
English

Rev 1.02 iv Document 900.0556
01/06
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the
limits for a Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Caution Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe A est conforme à norme NMB-003 du Canada.
Manufacturer’s Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant with
the essential protection requirements of the EMC directive 89/336/EEC and the Low
Voltage Directive LVD 73/23 EEC, conforming to the requirements of standards EN 55022
for emissions.

Rev 1.02 Document 900.0556
01/06
English
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Unpack Everything . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Mounting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Connecting Cables Through the Housing Base . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connecting Cables Through the Side Conduit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Electrical Box Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connecting the Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Adjusting the Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Adjusting the Lens Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Dip Switch Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Adjustment Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing the Enclosure Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Solving Common Technical Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Warranty and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Cable Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
HD4VC4HR Mounting Template. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Rev 1.02 1 Document 900.0556
01/06
English
Introduction
The unobtrusive, low-profile design of the HD4VC4HR CCTV Camera is ideal for indoor
and outdoor installations in commercial and residential venues.
Before You Begin
Please read this guide carefully before
you install the HD4VC4HR CCTV
Camera.
Keep this guide for future reference.

Rev 1.02 2 Document 900.0556
01/06
Unpack Everything
Check that the items received match those listed on the order form and packing slip. The
HD4VC4HR packing box should include, in addition to this User Guide:
• One fully-assembled HD4VC4HR camera, including factory-installed pigtail power and
video connections
• One HD4VC4HR hardware kit
• One bag containing mounting screws
• One Product warranty
If any parts are missing or damaged, contact the dealer you purchased the camera from or
call Honeywell Customer Service (see Warranty and Service).
Equipment Required
You will require the following tools to complete the installation:
• Phillips screwdriver
• Tools supplied in the hardware kit (three Allen keys: one for the security screw on the lid,
one for the conduit plug locking screw, one for the lens locking screw)
•Side-cutters

Rev 1.02 3 Document 900.0556
01/06
English
Installation
The HD4VC4HR is weather-sealed for indoor or outdoor locations. The HD4VC4HR is a
fully-integrated enclosure with camera and lens. The wiring can be completely concealed
to reduce the risk of tampering.
Figure 1 Installation Components
Mounting the Camera
The HD4VC4HR Camera is designed to be surface mounted on a wall or ceiling. Before
you mount the camera, use the mounting template provided on page 17 to mark and pre-
drill the holes.
HD4VC4HRdome
enclosure

Rev 1.02 4 Document 900.0556
01/06
Connecting Cables Through the Housing Base
For installations requiring pulling cables through the grommet located in the bottom of the
base:
1. Use a sharp knife to cut an opening in the base gasket (see the figure below). Be
careful. The opening should only be big enough to feed the cable assembly through.
2. Pull the cabling through the opening.
3. Apply appropriate sealant around the opening to prevent moisture from entering the
housing.
Connecting Cables Through the Side Conduit
1. Peel back the bottom flat gasket below the side conduit just enough to expose the security
screw.
2. Use the Allen key supplied to loosen and remove the security screw.
3. Use a flat screwdriver to unscrew the conduit plug.
4. Pull the cabling through the hole.
5. Apply appropriate sealant around the opening to prevent moisture from entering the
housing.
Base gasket opening


Rev 1.02 5 Document 900.0556
01/06
English
Electrical Box Installations
Figure 2 illustrates how to mount the HD4VC4HR directly to a 4S electrical box or directly
to wall or ceiling. For 4S electrical box installations, the optional adapter plate can be used
to cover ceiling or wall imperfections around the electrical box opening.
Figure 2 4S Electrical Box Installation
Note Honeywell recommends that you orient the conduit plug facing downwards
(wall mount installations) to prevent moisture from entering the housing.
Electrical box
(not supplied)
Adapter plate
(use is optional)
HD4VC4HR base
Secure the optional
adapter plate to the
4S electrical box
using appropriate
screws (not supplied)
Secure the HD4VC4HR base
with screws appropriate to
your installation (supplied)
For surface mount
installations (without an
electrical box), use
#6-1 7/16 inch slotted Type
A screws (x4) supplied
Ceiling/wall

Rev 1.02 6 Document 900.0556
01/06
Figure 3 illustrates how to mount the HD4VC4HR directly to a double gang or single gang
electrical box.
Figure 3 Double Gang/Single Gang Electrical Box Installation (Single Gang
Shown)
Electrical box
(not supplied)
HD4VC4HR base
Ceiling/wall
Secure the HD4VC4HR base
with screws appropriate to
your installation (not
supplied)
For surface mount
installations (without an
electrical box), use
#6-1 7/16 inch slotted Type
A screws (x4) supplied

Rev 1.02 7 Document 900.0556
01/06
English
Connecting the Wiring
Follow Figure 4 for the wiring connection.
Figure 4 Wiring Connection
Adjusting the Camera
To adjust the HD4VC4HR Camera:
1. Apply 12 VDC or 24 VAC to the camera and monitor the video signal.
2. Loosen the screws that lock the gimbal assembly in place (see Figure 5).
3. Adjust the camera carrier to the desired view.
4. Tighten the screws to lock the gimbal assembly in place.
Note Orient the camera as shown in Figure 5 to maintain the correct picture
orientation.
+_
Red Black
Power
Video: female BNC
Note For secure installations, surface
mounted cables should be
protected by plastic or metal
cable covers.

Rev 1.02 8 Document 900.0556
01/06
Figure 5 Gimbal Adjustment
Adjusting the Lens Focus
Lenses are pre-focused at the factory but may require a final adjustment after installation in
the unlikely event the optical effect of the dome causes a slight defocusing of the lens.
TECH TIP! To check the focus, hold the dome over the lens while making any
adjustments.
To adjust the camera direction, view angle and focus, connect the service monitor cable
(supplied) to the video monitor output.
Locking
screw
Set focus
Set focal length
Locking screw. Loosen to
adjust Horizontal (B).
Top view Angle view
Dip switches Legend:
A = Tilt rotation
B = Horizontal rotation
C = Pan rotation
B
C
A
Setscrews (x2). Loosen to
adjust Pan (C). Other setscrew
located on opposite side.

Rev 1.02 9 Document 900.0556
01/06
English
Dip Switch Functions
Figure 6 Dip Switch Settings
Adjustment Method
The table below describes the dip switches. The default settings are indicated in bold.
Switch no. Function Off On
1BLCOff On
2AE/MEAEME
3ATW/AWBAWBATW
4AGCOffOn
BLC AE/ME ATW/AWB AGC MAX
Video
monitor
output Upper locking
screw to set
focus
Lower locking
screw to set
focal length
Line lock: Push
to vary vertical
phase (24 VAC
operation only)
Auto Iris level
adjustment
Varifocal Auto Iris
connector
1 2 3 4
Factory (default) settings
= ON (up)
= OFF (down)
Top of
camera

Rev 1.02 10 Document 900.0556
01/06
Installing the Enclosure Cover
To install the enclosure cover, use the Allen key (supplied) to secure the HD4VC4HR dome
enclosure to the base with four #8-32 security screws.
Figure 7 Enclosure Cover Installation
Routine Maintenance
Use regular liquid cleaners to remove dirt and grime from the HD4VC4HR dome.
Caution Do not use harsh or abrasive cleaners which can scratch the
polycarbonate dome and reduce visibility for the camera.
If the camera view is obstructed by scratches, remove the front plate and rotate to find an
unscratched part of the dome.
HD4VC4HRdome
enclosure
#8-32 security
screws (x4)

Rev 1.02 11 Document 900.0556
01/06
English
Solving Common Technical Issues
Call Honeywell Technical Support for additional assistance (see Warranty and Service).
No Video ❐Check that the power supply voltage is within the operating
specifications for your camera model. See Specifications for
details.
❐Check the video signal connections are correct.
❐Check for a loose connection.
Fuzzy
Video
❐Check the video ground connections.
❐Check for ground loops.

Rev 1.02 12 Document 900.0556
01/06
Warranty and Service
Subject to the terms and conditions listed on the Product warranty, during the warranty
period Honeywell will repair or replace, at its sole option, free of charge, any defective
products returned prepaid.
In the event you have a problem with any Honeywell product, please call Customer Service
at 1.800.796.CCTV for assistance or to request a Return Merchandise Authorization
(RMA) number.
Be sure to have the model number, serial number, and the nature of the problem available
for the technical service representative.
Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped
to Honeywell without a clearly identified Return Merchandise Authorization (RMA)
number may be refused.

Rev 1.02 13 Document 900.0556
01/06
English
Specifications
Video Signal Specifications
Pickup device: 1/3 in. CCD High Resolution color image sensor
Synchronization system: Internal Sync, Line Lock External (24 VAC only)
Vertical phase adjustment: Adjustable ± 360° - top of board control
Horizontal resolution: More than 530 TV lines
Lens type: 3.3 - 12 mm @ F1.5
Minimum illumination
response:
0.8 Lux @ F1.5
Signal to noise ratio: Better than 50 dB (AGC Off)
Gain control: Automatic, selectable - top of board control
Lens iris control: DC Auto Iris type - top of board control
White balance: Selectable: ATW/AWB - top of board control
Backlight compensation: Selectable On/Off - top of board control
Video output: 1 V p-p composite
Video output impedance: 75 Ω
Format Specifications NTSC PAL
Color video signal format: Standard Standard
Effective picture elements: 768 (H) x 494 (V) 752 (H) x 582 (V)
Scanning system (2:1
interlace):
525 lines, 60 fields/sec. 625 lines, 50 fields/sec.
Electronic shutter: 1/60 - 1/100,000 second 1/50 - 1/100,000 second

Rev 1.02 14 Document 900.0556
01/06
General Specifications
Construction: Die cast (housing) Polycarbonate (dome)
Finish: Gray/off white powder coating
Dimensions: 5.5 in. (D) x 3.6 in. (H)
140.2 mm (D) x 91.5 mm (H)
Weight: 2.5 lb. (1.1 kg) max
Power supply auto
switching:
12 VDC @ 4 watts max.
24 VAC, 60 Hz @ 4 watts max. (UL/NTSC version)
24 VAC, 50 Hz @ 4 watts max. (CE/PAL version)
Storage temperature:
Operating temperature:
-49°F to +167°F (-45°C to +75°C)
-13°F to +131°F (-25°C to +55°C)
Relative operating humidity: 0% to 95% RH non-condensing